JTB00677NAS2

Service Bulletin Details

Public Details for: JTB00677NAS2

An oil leak from underneath the vehicle may be evident. Upon further inspection, the leak may be found to be from the transmission.

- 2019 - 2018 - 2017 - 2016 -

Models from 2019

Models from 2018

Models from 2017

Models from 2016

10/11/2019
https://www.odyssey.jlrint.com/odyssey/WorkflowHtmlComposition.do?wid=1570194977613
JTB00677NAS2
TECHNICAL BULLETIN
11 OCT 2019
© Jaguar Land Rover North America, LLC
NOTE: The information in Technical Bulletins is intended for use by trained, professional
Technicians with the knowledge, tools, and equipment required to do the job properly and
safely. It informs these Technicians of conditions that may occur on some vehicles, or
provides information that could assist in proper vehicle service. The procedures should not
be performed by 'do-it-yourselfers'. If you are not a Retailer, do not assume that a condition
described affects your vehicle. Contact an authorized Jaguar service facility to determine
whether this bulletin applies to a speciﬁc vehicle.
INFORMATION
This reissue replaces all previous versions. Please destroy all previous versions.
This bulletin supersedes TSB JTB00677NAS1/2019 dated 04 MAR 2019, which should either
be destroyed or clearly marked to show it is no longer valid (e.g. with a line across the page).
Only refer to the electronic version of this Technical Bulletin in TOPIx.
Changes are highlighted in blue
SECTION:
307-01A
SUBJECT/CONCERN:
Oil Leak From Transmission
AFFECTED VEHICLE RANGE:
MODEL:
MODEL
YEAR:
VIN:
ASSEMBLY
PLANT:
https://www.odyssey.jlrint.com/odyssey/WorkflowHtmlComposition.do?wid=1570194977613
APPLICABILITY:
1/8
10/11/2019
https://www.odyssey.jlrint.com/odyssey/WorkflowHtmlComposition.do?wid=1570194977613
MODEL:
MODEL
YEAR:
F-PACE
(X761)
20172019
045122329092
Solihull
INGENIUM I4 2.0L Petrol/GTDi 2.0L Petrol/INGENIUM I4
2.0L Diesel, Vehicles With: 8HP45 8-Speed Automatic
Transmission RWD
F-TYPE
(X152)
20182019
K48252K58803
Castle
Bromwich
INGENIUM I4 2.0L Petrol, Vehicles With: 8HP45 8-Speed
Automatic Transmission RWD
XE
(X760)
2017
917833979442
Solihull
GTDi 2.0L Petrol/INGENIUM I4 2.0L Diesel, Vehicles
With: 8HP45 8-Speed Automatic Transmission RWD
XE
(X760)
20172019
P00002P42562
Castle
Bromwich
INGENIUM I4 2.0L Petrol/INGENIUM I4 2.0L Diesel,
Vehicles With: 8HP45 8-Speed Automatic Transmission
RWD
XF
(X260)
20162018
Y11895Y73262
Castle
Bromwich
INGENIUM I4 2.0L Petrol/GTDi 2.0L Petrol/INGENIUM I4
2.0L Diesel, Vehicles With: 8HP45 8-Speed Automatic
Transmission RWD
VIN:
ASSEMBLY
PLANT:
APPLICABILITY:
MARKETS:
NORTH AMERICA
CONDITION SUMMARY:
SITUATION:
An oil leak from underneath the vehicle may be evident. Upon further inspection, the leak
may be found to be from the transmission.
CAUSE:
Manufacturing concern.
ACTION:
Follow the instructions below.
PARTS:
https://www.odyssey.jlrint.com/odyssey/WorkflowHtmlComposition.do?wid=1570194977613
2/8
10/11/2019
https://www.odyssey.jlrint.com/odyssey/WorkflowHtmlComposition.do?wid=1570194977613
NOTES:
An allowance of $18.20 USD or local equivalent has been provided to cover the
cost of the Loctite 542, 1 pack of 10 M10 grub screws, and 1 liter of transmission oil.
Claim using Sundry Code ‘ZZZ001’.
The allowance for M10 grub screws may only be claimed 1 time per 10 vehicles.
PART NUMBER
DESCRIPTION
QUANTITY
ZZZ001*
Loctite 542 or equivalent
$2.60
T2H30418
M8 Grub screw
1
ZZZ001
M10 x 16 mm - Pitch 1.5 mm - Steel - Hex socket Grub screw
$2.60
ZZZ001
1 liter Transmission oil
$13.00
WARRANTY:
NOTES:
Repair procedures are under constant review, and therefore times are subject to
change; those quoted here must be taken as guidance only. Use TOPIx to obtain
the latest repair time.
The JLR claims submission system requires the use of causal part numbers. Labor
only claims must show the causal part number with a quantity of zero.
SRO
TIME
(HOURS)
CONDITION
CODE
CAUSAL
PART
Grub screw - Install - Single/pair - FPACE
44.91.47
0.4
42
C2D19741
Transmission oil - Check and top up - FPACE
44.24.06
1.0
42
C2D19741
Grub screw - Install - Single/pair - FTYPE
44.91.47
0.2
42
C2D19741
Transmission oil - Check and top up - FTYPE
44.24.06
0.5
42
C2D19741
Grub screw - Install - Single/pair - XE, XF
44.91.47
0.3
42
C2D19741
DESCRIPTION
https://www.odyssey.jlrint.com/odyssey/WorkflowHtmlComposition.do?wid=1570194977613
3/8
10/11/2019
https://www.odyssey.jlrint.com/odyssey/WorkflowHtmlComposition.do?wid=1570194977613
SRO
TIME
(HOURS)
CONDITION
CODE
CAUSAL
PART
44.24.06
0.7
42
C2D19741
DESCRIPTION
Transmission oil - Check and top up XE, XF
NOTE:
Normal Warranty procedures apply.
SERVICE INSTRUCTION:
NOTE:
Some steps in this service instruction may not be applicable to certain vehicle
variants due to transmissions mountings being installed in the areas shown.
1.
Remove the engine undershield (see TOPIx Workshop Manual section 501-02: Front
End Body Panels - Removal and Installation - Engine Undershield).
2.
Conﬁrm the source of the transmission oil leak (see TOPIx Workshop Manual section
307-01A: Automatic Transmission/Transaxle-RWD - Diagnosis and Testing).
https://www.odyssey.jlrint.com/odyssey/WorkflowHtmlComposition.do?wid=1570194977613
4/8
10/11/2019
https://www.odyssey.jlrint.com/odyssey/WorkflowHtmlComposition.do?wid=1570194977613
3.

Identify the root cause of the transmission oil leak.
If the transmission oil leak is from the area shown, continue to step
4.
If the transmission oil leak is not from the area shown, continue to
step 5.
https://www.odyssey.jlrint.com/odyssey/WorkflowHtmlComposition.do?wid=1570194977613
5/8
10/11/2019
https://www.odyssey.jlrint.com/odyssey/WorkflowHtmlComposition.do?wid=1570194977613
4.
NOTE:
Make sure the area is clean and free from foreign material.

Apply Loctite 542 or equivalent to the new grub screw and install the new grub
screw.
The grub screw must be installed ﬂush with the surface of the
transmission casing.
https://www.odyssey.jlrint.com/odyssey/WorkflowHtmlComposition.do?wid=1570194977613
6/8
10/11/2019
https://www.odyssey.jlrint.com/odyssey/WorkflowHtmlComposition.do?wid=1570194977613
5.

Identify the root cause of the transmission oil leak.
If the transmission oil leak is from the area shown, continue to step
6.
If the transmission oil leak is not from the area shown, continue to
step 7.
If the transmission oil leak is not from the area shown and there was
no transmission oil leak found in step 3, submit a Technical
Assistance (TA) request with all supporting evidence attached.
https://www.odyssey.jlrint.com/odyssey/WorkflowHtmlComposition.do?wid=1570194977613
7/8
10/11/2019
https://www.odyssey.jlrint.com/odyssey/WorkflowHtmlComposition.do?wid=1570194977613
6.
NOTE:
Make sure the area is clean and free from foreign material.

Apply Loctite 542 or equivalent to the new grub screw and install the new grub
screw.
The grub screw must be installed ﬂush with the surface of the
transmission casing.
7.
NOTE:
The Loctitie should be allowed to cure for 4 hours before the oil level check
procedure is completed.
Check the transmission oil level and ﬁll as required (see TOPIx Workshop Manual
section 307-01: General Procedures - Transmission Fluid Level Check).
8.
Install the engine undershield (see TOPIx Workshop Manual section 501-02: Front
End Body Panels - Removal and Installation - Engine Undershield).
https://www.odyssey.jlrint.com/odyssey/WorkflowHtmlComposition.do?wid=1570194977613
8/8