NTB18-062b

Classification:
Reference:
EC18-028b
Date:
NTB18-062b
October 24, 2019
2018 ARMADA AND TITAN;
MIL ON WITH DTC P0138 AND/OR P0158
This bulletin has been amended. See AMENDMENT HISTORY on the last page.
Please discard previous versions of this bulletin.
APPLIED VEHICLES:
APPLIED ENGINE:
2018 Armada (Y62)
2018 Titan (A61)
2018 Titan XD (A61)
VK56VD (gasoline V8)
IF YOU CONFIRM
The MIL is ON with one or both of the following DTCs:

P0138 (Heated oxygen sensor heater 2 [bank 1] circuit high voltage)

P0158 (Heated oxygen sensor heater 2 [bank 2] circuit high voltage)
And
There are no drivability issues.
ACTION
1.
Refer to step 6 in the SERVICE PROCEDURE to confirm this bulletin applies to the
vehicle you are working on.
2.
If this bulletin applies, reprogram the ECM.
IMPORTANT: The purpose of ACTION (above) is to give you a quick idea of the work you
will be performing. You MUST closely follow the entire SERVICE PROCEDURE as it
contains information that is essential to successfully completing this repair.
Nissan Bulletins are intended for use by qualified technicians, not 'do-it-yourselfers'. Qualified technicians are
properly trained individuals who have the equipment, tools, safety instruction, and know-how to do a job
properly and safely. NOTE: If you believe that a described condition may apply to a particular vehicle, DO
NOT assume that it does. See your Nissan dealer to determine if this applies to your vehicle.
1/10
SERVICE PROCEDURE
ECM REPROGRAMMING
IMPORTANT: Before starting, make sure:

ASIST on the CONSULT PC has been synchronized (updated) to the current date.

All CONSULT-III plus (C-III plus) software updates (if any) have been installed.

The CONSULT PC is connected to the Internet (Wi-Fi or cable).
NOTE:

Most instructions for reprogramming with C-III plus are displayed on the CONSULT
PC screen.

If you are not familiar with the reprogramming procedure, click here. This will link
you to the "CONSULT- III plus (C-III plus) ECM Reprogramming" general procedure.

Take the vehicle for a 10 minute drive in order to meet the following Idle Air Volume
Learn (IAVL) conditions:
 Engine coolant temperature: 70 - 100°C
(158 - 212°F)
 Battery voltage: More than 12.9V (At idle)
 Transmission: Warmed up

After reprogramming is complete, you will be
required to perform Throttle Valve Closed
Position, Idle Air Volume Learn, Accelerator
Closed Position, and DTC erase.
Figure A
CAUTION:

Connect a battery maintainer or smart charger set to reflash mode or a similar
setting. If the vehicle battery voltage drops below 12.0V or above 15.5V during
reprogramming, the ECM may be damaged.

Be sure to turn OFF all vehicle electrical loads.
If a vehicle electrical load remains ON, the ECM may be damaged.

Be sure to connect the AC Adapter.
If the CONSULT PC battery voltage drops during reprogramming, the process
will be interrupted and the ECM may be damaged.

Turn OFF all external Bluetooth® devices (e.g., cell phones, printers, etc.)
within range of the CONSULT PC and the plus VI. If Bluetooth® signal waves
are within range of the CONSULT PC and plus VI during reprogramming,
reprogramming may be interrupted and the ECM may be damaged.
2/10
NTB18-062b
1. Connect the CONSULT PC to the vehicle to begin the reprogramming procedure.
2. Start C-III plus.
3. Wait for the plus VI to be recognized / connected.

The serial number will display when the plus VI is recognized / connected.
4. Select Re/programming, Configuration.
Step 3: plus
VI is
recognized
Step
4
Figure 1
5. Follow the on-screen instructions and navigate the C-III plus to the screen shown in
Figure 2 on the next page.
3/10
NTB18-062b
6. When the screen in Figure 2 displays, confirm this bulletin applies as follows.
A. Find the ECM Part Number and write it on the repair order.
NOTE: This is the current ECM Part Number (P/N).
6A: Current ECM P/N
Figure 2
B. Compare the P/N you wrote down to the numbers in the CURRENT ECM PART
NUMBER column in Table A below.

If there is a match, this bulletin applies. Continue with the reprogramming
procedure.

If there is not a match, reprogramming does not apply. Refer to ASIST for
further diagnosis.
Table A
MODEL
CURRENT ECM PART NUMBER: 23710-
2018 Armada
6GY2A, 6GY2B, 6GY3A, 6GY3B
6GY4A, 6GY4B, 6GY5A, 6GY5B
2018 Titan and
Titan XD
9FT1B, 9FT1C, 9FT2B,
9FT4B, 9FT4C, 9FT5B,
EZ54A, EZ54B,
EZ56A, EZ56B,
4/10
9FT2C,
9FT6B,
EZ55A,
EZ57A,
9FT3B, 9FT3C
9FT7B, 9FT8B
EZ55B
EZ57B
NTB18-062b
7. Follow the on-screen instructions to navigate C-III plus and reprogram the ECM.
NOTE:
 In some cases, more than one new P/N for reprogramming is available.
 In this case, the screen in Figure 3 displays.
 Select and use the reprogramming option that does not have the message
“Caution! Use ONLY with NTBXX-XXX”.
 If you get this screen and it is blank (no reprogramming listed), it means there is no
reprogramming available for this vehicle. Close C-III plus and refer back to ASIST for
further diagnosis.
Figure 3

Before reprogramming will start, you will be required to enter your User Name and
Password.
 The CONSULT PC must be connected to the Internet (Wi-Fi or cable).
 If you do not know your Username and Password, contact your service
manager.
Figure 4
5/10
NTB18-062b
8. When the screen in Figure 5 displays, reprogramming is complete.
NOTE: If the screen in Figure 5 does not display (reprogramming does not complete),
refer to the information on page 7.
9. Disconnect the battery maintainer/smart charger from the vehicle.
10. Select Next.
Step
10
Figure 5
NOTE:

In the next steps, starting on page 8, you will perform Throttle Valve Closed Position,
Idle Air Volume Learn, Accelerator Closed Position, and DTC erase.

These operations are required before C-III plus will provide the final reprogramming
confirmation report.
6/10
NTB18-062b
ECM Recovery
Do not disconnect plus VI or shut down Consult III plus if reprogramming does not
complete.
If reprogramming does not complete and the “!?” icon displays as shown in
Figure 6:

Check battery voltage
(12.0 - 15.5 V).

Ignition is ON, engine OFF.

External Bluetooth® devices
are OFF.

All electrical loads are OFF.

Select retry and follow the
on screen instructions.

“Retry” may not go through on
first attempt and can be
selected more than once.
Figure 6
If reprogramming does not complete and the “X” icon displays as shown in
Figure 7:

Check battery voltage
(12.0 - 15.5 V).

CONSULT A/C adapter is
plugged in.

Ignition is ON, engine OFF.

Transmission is in Park.

All C-III plus / VI cables are
securely connected.

All C-III plus updates are
installed.

Select Home, and restart
the reprogram procedure
from the beginning.
Figure 7
7/10
NTB18-062b
11. Follow the on-screen instructions to perform the following:

Throttle Valve Closed Position.

Idle Air Volume Learn (IAVL).
NOTE:
 Listed below are common conditions required for IAVL to complete.
 If IAVL does not complete within a few minutes, a condition may be out of
range.
 Refer to the appropriate ESM for specific conditions required for the
vehicle you are working on.
o Engine coolant temperature: 70 - 100°C (158 - 212°F)
o Battery voltage: More than 12.9V (At idle)
o Selector lever: P or N
o Electric load switch: OFF (Air conditioner, headlamp, rear window defogger)
o Steering wheel: Neutral (Straight-ahead position)
o Vehicle speed: Stopped
o Transmission: Warmed up

Accelerator Pedal Close Position Learning

Erase DTCs
Continue to the next page.
8/10
NTB18-062b
12. When the entire reprogramming process is complete, the screen in Figure 8 will display.
13. Verify the before and after part numbers are different.
14. Print a copy of this screen (Figure 8) and attach it to the repair order for warranty
documentation.
15. Select Confirm.
Step
13
Step
14
Step
15
Figure 8
16. Close C-III plus.
17. Turn the ignition OFF.
18. Disconnect the plus VI from the vehicle.
CLAIMS INFORMATION
Submit a Primary Part (PP) type line claim using the following claims coding:
DESCRIPTION
PFP
OP CODE SYM
DIA
FRT
Reprogram Engine Control Module
(1)
DE97AA
HD
32
(2) (3)
(1)
(2)
(3)
Refer to the electronic parts catalog (FAST or equivalent) and use the ECM assembly
part number (23703-*****) as the Primary Failed Part (PFP).
Reference the current Nissan Warranty Flat Rate Manual and use the indicated FRT.
FRT allows adequate time to access DTC codes and reprogram ECM. No other
diagnostic procedures subsequently required. Do NOT claim any Diagnostic Op
Codes with this claim.
9/10
NTB18-062b
AMENDMENT HISTORY
PUBLISHED DATE
REFERENCE
DESCRIPTION
September 11, 2018
NTB18-062
Original bulletin published
October 19, 2018
NTB18-062a
Table A revised
October 24, 2019
NTB18-062b
APPLIED VEHICLES section and Table A
revised
10/10
NTB18-062b