20TechRefREV124
Service Bulletin Details
Public Details for: 20TechRefREV124
Added a8 e & q5 e to titles & index
- 2020 -
Models from 2020
2020 Pre-Delivery Inspection Technician Reference Document Effective 1-24-2020-US Version 1.5 Table of Contents Technician Reference Document Technician Reference Document Overview The Pre-Delivery Inspection Technician Reference Document is designed to be a resource used in hand with the Pre-Delivery Inspection Checklist (PDI). The PDI Checklist has been simplified to make the process more efficient, and in doing so, this document has been created to be used as a reference for checklist items that may have additional information. On the PDI Checklist, you find that certain items have been notated with an asterisk symbol (*), this lets you know that additional information can be found in this Technician Reference Document. Below you will find a list of each model, with the page numbers to their left. After navigating to the desired page, you will notice each model page is formatted similarly to the PDI Checklists. After each section title is the original checklist item, followed by any additional information specific to that model. Table of Contents 3-4 A3/S3/RS 3 5-6 A4/S4/A4 allroad 7-8 A5/S5 9-11 A6/S6/A6 allroad 12-14 A7/S7 15-16 A8 L/A8 e/S8 17-18 e-tron 19-20 Q3 21-23 Q5/Q5 e/SQ5 24-25 Q7/SQ7 26-27 Q8/SQ8/RS Q8 28-29 R8 30-31 TT/TTS/TTRS Effective 1-24-2020-US Version 1.5 Model Year 2020 | Audi Pre-Delivery Reference Document | 2 A3/S3/RS 3 Technician Reference Document Vehicle Preparation Lighting and Windshield • Set adaption channel to enable CD Ripping using Guided Functions (if equipped with NAV) • Test front washers (and headlight washers on S3 and RS 3). Correct aim if necessary Set adaptation channel (via Special functions > Service work > 5F-Activating/deactivating storage of music). Also referred to as CD Ripping. Perform 3 button reset of the MMI to complete the activation. Refer to the owner’s manual for model-specific button sequence • Perform any open campaigns Follow instructions listed in campaign documentation • Perform diagnostic work Connect vehicle diagnostic tester • Select “Diagnosis” mode and start diagnosis • Perform vehicle identification • Untick “Working with Guided Fault Finding” • Switch to “Special functions” tab and select following program: Delivery Inspection total • Start program by selecting “Carry out check” • Continue to follow instructions on screen and complete the process • Switch to the “Control units” tab, press the “Guided Fault Finding” button and launch Guided Fault Finding as far as the test plan Headlights must be on to test functionality of the headlight washers Trunk Inspection • Install wheel bolt cover removal tool from PDI kit into trunk tool kit Install wheel bolt cover removal tool from PDI kit and wheel lock key (if applicable) into trunk tool kit • Verify temporary inflatable spare tire is present (A3 Sedan and S3 FWD only) See separate “Audi Normal Load Condition Tire Pressure Table” posted on ServiceNet • Check battery clamps for proper torque Refer to Elsa Pro for specification Interior • Check operation of window, lock, and seat controls Check operation of all switches: Locks, windows, seat adjustment, heated seats (if equipped) and child safety features • Inspect mirrors for proper operation Inspect folding, adjustments, right side tilt in reverse, heating (if equipped) • The static event memory entries must be evaluated and, if necessary, processed using Guided Fault Finding • Check rear view mirror operation • Exit diagnosis; diagnostic log for delivery inspection is sent automatically • Verify proper operation of climate control • Install front license plate carrier (if necessary) • Retain any removed trim required for carrier installation and give to the customer. If no front license plate carrier is necessary ensure the carrier remains in the trunk for the customer Exterior • Check all key buttons and features Check functionality of all keys. Verify vehicle starts and runs with all keys and the start/stop button. Verify all doors and trunk remotely lock/unlock with all keys, including all door handle sensors with Advanced Key (if equipped) Check self-dimming function/lighting Ensure proper heating and A/C cooling and open all panel vents for all zones • Inspect operation of all power outlets Inspect operation of front outlet, aux. outlet under armrest, and rear outlets • Check panoramic sunroof and sunshade operation (Sedan only) Verify open/close/vent/deflector at edge and sunshade operation Settings • Set time source setting to “GPS” (if equipped) and set auto daylight savings time to “on”* Change time zone appropriate to dealer location • Verify and set language and measurement units This can be changed in the Settings menu by going to Menu > Vehicle > Vehicle settings Effective 1-24-2020-US Version 1.5 Model Year 2020 | Audi Pre-Delivery Reference Document | 3 A3/S3/RS 3 Technician Reference Document Settings (continued) Driving Performance • Verify Speech Dialog System is operating (if equipped) • Verify engine Start-Stop System functionality Press the “Talk” button and verify several commands • Set “Entertain. Fad.” in Parking aid to an audible level (if equipped) Via “Menu > Vehicle > Left Option > Driver Assistance > Parking Aid” • Set dealership location in navigation (if equipped) Set dealership location for following back to dealership during road test • Turn off Manual Speed Warning This can be changed in the Driver Assistance Settings by going to Menu > Vehicle > Driver Assistance > Speed Warning > Manual > Select OffMedia / Radio / SAT Verify the velum sticker is on the start/stop button. Remove the start/stop information card from the car kit and place it in the glove box with the owner’s manuals. Additional supply can be ordered via the Brand Store on AccessAudi • Verify engine performance and acceleration Listen for abnormal noise/vibrations • Test drive vehicle applying brakes several times Apply brakes at least 4 times at 20 mph (35 km/h) to clean brake rotors. Check for abnormal noise/vibration/pulsation • Calibrate rear view mirror Calibrate rear view mirror compass to proper zone and check self-dimming function/lighting (if equipped) Media / Radio / SAT Driver Assistance • Verify HD Radio is turned “off” • Verify operation of Audi parking system (if equipped) This can be found in the Radio/Settings Menu Verify operation of Audi parking system sensors with rear view camera (if equipped) Audi connect® (USA ONLY) (if equipped) • Turn on the Wi-Fi® hotspot (if equipped) Ensure the wireless network is turned on (Telephone > Right Option > Wi-Fi® options > Wi-Fi® “On”) • Check Wi-Fi® hotspot visibility. No data available at PDI (if equipped) Post-Road Test Inspection • Check engine oil level Fill oil to the max level when the vehicle is at operating temperature Check Wi-Fi® hotspot functionality is enabled and verify the SSID is set to “AUDIXXXXX”, where XXXXX = the last five digits of VIN that are automatically preset in the system • Enable satellite map view for navigation (if equipped) Enable satellite map view in the Navigation > Map Settings and verify the satellite imagery appears in the navigation map screen On-Hoist Inspection • Inspect wheel bolts for proper torque Use torque wrench to verify • Install wheel bolt covers and center caps as supplied Wheel bolt covers and center caps can be found in the PDI kit • Set and store tire pressures for either sold vehicle OR stock inventory vehicle If a known “sold” unit, set to appropriate Normal Load Condition. See separate “Audi Normal Load Condition Tire Pressure Table” posted on ServiceNet. If going to stock, set to maximum recommended tire pressures listed on the B-pillar door jamb, and store tire pressure values in Car/System menu Effective 1-24-2020-US Version 1.5 Model Year 2020 | Audi Pre-Delivery Reference Document | 4 A4/S4/A4 allroad Technician Reference Document Vehicle Preparation Trunk Inspection (continued) • Perform any open campaigns • Set spare tire pressure Follow instructions listed in campaign documentation • Perform diagnostic work Connect vehicle diagnostic tester • Select “Diagnosis” mode and start diagnosis • Perform vehicle identification • Untick “Working with Guided Fault Finding” • Switch to “Special functions” tab and select following program: Delivery Inspection total • Start program by selecting “Carry out check” • Continue to follow instructions on screen and complete the process • Switch to the “Control units” tab, press the “Guided Fault Finding” button and launch Guided Fault Finding as far as the test plan • The static event memory entries must be evaluated and, if necessary, processed using Guided Fault Finding • Exit diagnosis; diagnostic log for delivery inspection is sent automatically • Install front license plate carrier (if necessary) • Retain any removed trim required for carrier installation and give to the customer. If no front license plate carrier is necessary ensure the carrier remains in the trunk for the customer Exterior • Check all key buttons and features Check functionality of all keys. Verify vehicle starts and runs with all keys and the start/stop button. Verify all doors and trunk remotely lock/unlock with all keys, including all door handle sensors with Advanced Key (if equipped) Lighting and Windshield • Test front washers (and headlight washers if equipped). Correct aim if necessary Headlights must be on to test functionality of the headlight washers See separate “Audi Normal Load Condition Tire Pressure Table” posted on ServiceNet • Check battery clamps for proper torque Refer to Elsa Pro for specification Interior • Check operation of window, lock, and seat controls Check operation of all switches: Locks, windows, seat adjustment, heated seats (if equipped) and child safety features • Inspect mirrors for proper operation Inspect folding, adjustments, right side tilt in reverse, heating • Check rear view mirror operation Check self-dimming function/lighting • Verify proper operation of climate control Ensure proper heating and A/C cooling and open all panel vents for all zones • Inspect operation of all power outlets Inspect operation of front outlet, aux. outlet under armrest, and rear outlets • Check panoramic sunroof and sunshade operation Verify open/close/vent/deflector at edge and sunshade operation Settings • Set Time source setting to “GPS” and set Auto daylight savings time to “on.” Change time zone appropriate to the dealer location • Verify and set language and measurement units This can be changed in the Settings menu by going to Menu > Vehicle > Vehicle settings • Verify Speech Dialog System is operating Press the “Talk” button and verify several commands • Set “Entertain. Fad.” in Parking aid to an audible level Via “Menu > Vehicle > Left Option > Driver Assistance > Parking Aid” • Set “Music volume while parking” to medium Trunk Inspection • Install wheel bolt cover removal tool from PDI kit into trunk tool kit Install wheel bolt cover removal tool from PDI kit and wheel lock key (if applicable) into trunk tool kit Effective 1-24-2020-US Version 1.5 Accessed via MMI rear view camera display, Settings > Music volume while parking (applies to vehicles with park assist or rear view camera) • Model Year 2020 | Audi Pre-Delivery Reference Document | 5 A4/S4/A4 allroad Technician Reference Document Settings (continued) Driving Performance (continued) • Set dealership location in navigation (if equipped) • Verify engine performance and acceleration Set dealership location for following back to dealership during road test • Turn off Manual Speed Warning (if equipped) This can be changed in the Driver Assistance settings by going to Menu > Vehicle > Driver Assistance > Speed Warning > Manual > Select Off Media / Radio / SAT • Verify HD Radio is turned “off” This can be found in the Radio/Settings Menu Audi connect® (USA ONLY) (if equipped) • Turn on the Wi-Fi® hotspot (if equipped) Ensure the wireless network is turned on (Telephone > Right Option > Wi-Fi® options > Wi-Fi® “On”) • Check Wi-Fi® hotspot visibility. No data available at PDI (if equipped) Check Wi-Fi® hotspot functionality is enabled and verify the SSID is set to “AUDIXXXXX”, where XXXXX = the last five digits of VIN that are automatically preset in the system • Enable Google Earth view for navigation (if equipped) Enable Google Earth view in the Navigation > Map Settings and verify the white Google logo appears in the bottom righthand corner of the MMI screen next to the LTE symbol. Listen for abnormal noise/vibrations • Test drive vehicle applying brakes several times Apply brakes at least 4 times at 20 mph (35 km/h) to clean brake rotors. Check for abnormal noise/vibration/pulsation • Calibrate rear view mirror Calibrate rear view mirror compass to proper zone and check self-dimming function/lighting (if equipped) Driver Assistance • Verify operation of parking system (if equipped) Verify operation of Audi parking system sensors with rear view camera (if equipped) • Verify all vehicle Head-up display functionality (if equipped) Verify the image can be adjusted properly in the viewing area of the windshield. Verify NAV directions, speed, cruise control, and lane assist are all visible in Head-up display (as equipped) Post-Road Test Inspection • Check engine oil level Fill oil to the max level when the vehicle is at operating temperature On-Hoist Inspection • Inspect wheel bolts for proper torque Use torque wrench to verify • Install wheel bolt covers and center caps as supplied Wheel bolt covers and center caps can be found in the PDI kit • Set and store tire pressures for either sold vehicle OR stock inventory vehicle If a known “sold” unit, set to appropriate Normal Load Condition. See separate “Audi Normal Load Condition Tire Pressure Table” posted on ServiceNet. If going to stock, set to maximum recommended tire pressures listed on the B-pillar door jamb, and store tire pressure values in Car/System menu Driving Performance • Verify engine Start-Stop System functionality Verify the velum sticker is on the start/stop button. Remove the start/stop information card from the car kit and place it in the glove box with the owner’s manuals. Additional supply can be ordered via the Brand Store on AccessAudi Effective 1-24-2020-US Version 1.5 Model Year 2020 | Audi Pre-Delivery Reference Document | 6 A5/S5 Technician Reference Document Vehicle Preparation Trunk Inspection (continued) • Perform any open campaigns • Set spare tire pressure Follow instructions listed in campaign documentation • Perform diagnostic work Connect vehicle diagnostic tester • Select “Diagnosis” mode and start diagnosis • Perform vehicle identification • Untick “Working with Guided Fault Finding” • Switch to “Special functions” tab and select following program: Delivery Inspection total • Start program by selecting “Carry out check” • Continue to follow instructions on screen and complete the process • Switch to the “Control units” tab, press the “Guided Fault Finding” button and launch Guided Fault Finding as far as the test plan • The static event memory entries must be evaluated and, if necessary, processed using Guided Fault Finding • Exit diagnosis; diagnostic log for delivery inspection is sent automatically • Install front license plate carrier (if necessary) • Retain any removed trim required for carrier installation and give to the customer. If no front license plate carrier is necessary ensure the carrier remains in the trunk for the customer Exterior • Check all key buttons and features Check functionality of all keys. Verify vehicle starts and runs with all keys and the start/stop button. Verify all doors and trunk remotely lock/unlock with all keys, including all door handle sensors with Advanced Key (if equipped) See separate “Audi Normal Load Condition Tire Pressure Table” posted on ServiceNet • Check battery clamps for proper torque Refer to Elsa Pro for specification Interior • Check operation of window, lock, and seat controls Check operation of all switches: Locks, windows, seat adjustment, heated seats (if equipped) and child safety features • Inspect mirrors for proper operation Inspect folding, adjustments, right side tilt in reverse, heating (if equipped) • Check rear view mirror operation Check self-dimming function/lighting (if equipped) • Verify proper operation of climate control Ensure proper heating and A/C cooling and open all panel vents • Inspect operation of all power outlets Inspect operation of front outlet, aux. outlet under armrest, and rear outlets • Check panoramic sunroof and sunshade operation Verify open/close/vent/deflector at edge and sunshade operation Settings • Set Time source setting to “GPS” and set Auto daylight savings time to “on.” Change time zone appropriate to the dealer location • Verify and set language and measurement units This can be changed in the Setup/Settings menu • Verify Speech Dialog System is operating Press the “Talk” button and verify several commands Lighting and Windshield • Test windshield washers. Correct aim if necessary Headlights must be on to test functionality of the headlight washers Trunk Inspection • Install wheel bolt cover removal tool from PDI kit into trunk tool kit Install wheel bolt cover removal tool from PDI kit and wheel lock key (if applicable) into trunk tool kit Effective 1-24-2020-US Version 1.5 • Set “Entertain. Fad.” in Parking aid to an audible level Via Menu > Vehicle > Driver Assistance > Parking Aid • Set “Music volume while parking” to medium Accessed via MMI rear view camera display, Settings > Music volume while parking (applies to vehicles with park assist or rear view camera) • Set dealership location in navigation (if equipped) Set dealership location for following back to dealership during road test Model Year 2020 | Audi Pre-Delivery Reference Document | 7 A5/S5 Technician Reference Document Settings (continued) Driving Performance (continued) • Turn off Manual Speed Warning (if equipped) • Test drive vehicle applying brakes several times This can be changed in the Driver Assistance settings by going to Menu > Vehicle > Driver Assistance > Speed Warning > Manual->Select Off Media / Radio / SAT • Verify HD Radio is turned “off” This can be found in the Radio/Settings Menu Audi connect® (USA ONLY) (if equipped) • Turn on the Wi-Fi® hotspot (if equipped) Ensure the wireless network is turned on (Telephone > Right Option > Wi-Fi® options > Wi-Fi® “On”) • Check Wi-Fi® hotspot visibility. No data available at PDI (if equipped) Check Wi-Fi® hotspot functionality is enabled and verify the SSID is set to “AUDIXXXXX”, where XXXXX = the last five digits of VIN that are automatically preset in the system • Enable Google Earth view for navigation (if equipped) Enable Google Earth view in the Navigation > Map Settings and verify the white Google logo appears in the bottom righthand corner of the MMI screen next to the LTE symbol. On-Hoist Inspection • Install wheel bolt covers and center caps as supplied Wheel bolt covers and center caps can be found in the PDI kit • Inspect wheel bolts for proper torque Apply brakes at least 4 times at 20 mph (35 km/h) to clean brake rotors. Check for abnormal noise/ vibration/pulsation • Calibrate rear view mirror Calibrate rear view mirror compass to proper zone and check self-dimming function/lighting (if equipped) Driver Assistance • Verify operation of parking system (if equipped) Verify operation of Audi parking system sensors with rear view camera (if equipped) • Verify all vehicle Head-up display functionality (if equipped) Verify the image can be adjusted properly in the viewing area of the windshield. Verify NAV directions, speed, cruise control, and lane assist are all visible in Head-Up Display (as equipped) Convertible Functionality (if equipped) • Test operation of power folding top Perform with engine running to conserve battery power Post-Road Test Inspection • Check engine oil level Fill oil to the max level when the vehicle is at operating temperature Use torque wrench to verify • Set and store tire pressures for either sold vehicle OR stock inventory vehicle If a known “sold” unit, set to appropriate Normal Load Condition. See separate “Audi Normal Load Condition Tire Pressure Table” posted on ServiceNet. If going to stock, set to maximum recommended tire pressures listed on the B-pillar door jamb, and store tire pressure values in Car/System menu Driving Performance • Verify engine Start-Stop System functionality Verify the velum sticker is on the start/stop button. Remove the start/stop information card from the car kit and place it in the glove box with the owner’s manuals. Additional supply can be ordered via the Brand Store on AccessAudi • Verify engine performance and acceleration Listen for abnormal noise/vibrations Effective 1-24-2020-US Version 1.5 Model Year 2020 | Audi Pre-Delivery Reference Document | 8 A6/S6/A6 allroad Technician Reference Document Vehicle Preparation Trunk Inspection • Perform any open campaigns • Install wheel bolt cover removal tool from PDI kit into trunk tool kit Follow instructions listed in campaign documentation • Perform diagnostic work Connect vehicle diagnostic tester • Select “Diagnosis” mode and start diagnosis • Perform vehicle identification • Untick “Working with Guided Fault Finding” • Switch to “Special functions” tab and select following program: Delivery Inspection total • Start program by selecting “Carry out check” • Continue to follow instructions on screen and complete the process • Switch to the “Control units” tab, press the “Guided Fault Finding” button and launch Guided Fault Finding as far as the test plan Install wheel bolt cover removal tool from PDI kit and wheel lock key (if applicable) into trunk tool kit • Set spare tire pressure See separate “Audi Normal Load Condition Tire Pressure Table” posted on ServiceNet • Check battery clamps for proper torque Refer to Elsa Pro for specification • Place one PR Number Label in the Warranty and Maintenance Book inside front cover and one on the Rear Panel Sill Frame under the luggage compartment floor, if not already there For vehicles produced prior to September 12, 2018 Labels are located in the trunk on top of spare tire Rear Panel Sill Frame location: Top Arrow • The static event memory entries must be evaluated and, if necessary, processed using Guided Fault Finding • Exit diagnosis; diagnostic log for delivery inspection is sent automatically • Install front license plate carrier (if necessary) • Retain any removed trim required for carrier installation and give to the customer. If no front license plate carrier is necessary ensure the carrier remains in the trunk for the customer Exterior • Check all key buttons and features Check functionality of all keys. Verify vehicle starts and runs with all keys and the start/stop button. Verify all doors and trunk remotely lock/unlock with all keys, including all door handle sensors with Advanced Key (if equipped) • Check all doors for proper power closing (if equipped) For vehicles equipped with the power door closing feature, check all doors for proper closing Lighting and Windshield • Test front washers (and headlight washers if equipped). Correct aim if necessary Headlights must be on to test functionality of the headlight washers Effective 1-24-2020-US Version 1.5 Model Year 2020 | Audi Pre-Delivery Reference Document | 9 A6/S6/A6 allroad Technician Reference Document Trunk Inspection (continued) Settings Warranty and Maintenance inside cover placement • Set Time source setting to “GPS” and set Auto daylight savings time to “on” Change time zone appropriate to the dealer location • Verify and set language and measurement units This can be changed in the Setup/Settings menu • Verify Speech Dialog System is operating Press the “Talk” button and verify several commands • Set “Music volume while parking” to medium Accessed via MMI rear view camera display, Settings > Music volume while parking (applies to vehicles with park assist or rear view camera) • Set dealership location in navigation Set dealership location for following back to dealership during road test • Turn off Manual Speed Warning (if equipped) Interior • Check operation of window, lock, and seat controls Check operation of all switches: Locks, windows, seat adjustment, heated seats and child safety features This can be changed in the Driver Assistance Settings by going to Menu > Vehicle > Driver Assistance > Speed Warning > Manual > Select Off Media / Radio / SAT • Verify HD Radio is turned “off” This can be found in the Radio/Settings Menu • Inspect mirrors for proper operation Inspect folding, adjustments, right side tilt in reverse, heating (if equipped) • Check rear view mirror operation Check self-dimming function/lighting (if equipped) • Verify operation of heated/ventilated and massaging seats (if equipped) Check both front and rear. Massaging feature is in the front seats only (if equipped) • Verify proper operation of climate control* Ensure proper heating and A/C cooling, open all panel vents for all zones • Inspect operation of all power outlets Inspect operation of front outlet, aux. outlet under armrest, and rear outlets • Check sunroof and sunshade operation Verify open/close/vent/deflector at edge and sunshade operation Audi connect® (USA ONLY) (if equipped) • Turn on the Wi-Fi® hotspot (if equipped) Ensure the wireless network is turned on (Telephone > Options > Wi-Fi® options > Wi-Fi® Mode “Hotspot” ) • Check Wi-Fi® hotspot visibility. No data available at PDI due to dealer demo mode (if equipped) Check Wi-Fi® hotspot functionality is enabled and verify the Access point (SSID) is set to “Audi_MMI_XXXX”, where XXXX is the last four digits of the VIN. Via Telephone > Options > Wi-Fi® options > Wi-Fi® Mode “Hotspot” > Hotspot settings > Access point (SSID) • Enable satellite map for navigation (if equipped) Enable satellite map in the Navigation > Gear icon > Map Settings and verify the white Google logo appears in the bottom right-hand corner of the Navigation map screen. On-Hoist Inspection • Install wheel bolt covers and center caps as supplied Wheel bolt covers can be found in the PDI kit • Inspect wheel bolts for proper torque Use torque wrench to verify Effective 1-24-2020-US Version 1.5 Model Year 2020 | Audi Pre-Delivery Reference Document | 10 A6/S6/A6 allroad Technician Reference Document On-Hoist Inspection (continued) • Set and store tire pressures for either sold vehicle OR stock inventory vehicle If a known “sold” unit, set to appropriate Normal Load Condition. See separate “Audi Normal Load Condition Tire Pressure Table” posted on ServiceNet. If going to stock, set to maximum recommended tire pressures listed on the B-pillar door jamb, and store tire pressure values in Car/System menu Driving Performance • Verify engine Start-Stop System functionality Verify the velum sticker is on the start/stop button. Remove the start/stop information card from the car kit and place it in the glove box with the owner’s manuals. Additional supply can be ordered via the Brand Store on AccessAudi • Verify engine performance and acceleration Listen for abnormal noise/vibrations • Test drive vehicle applying brakes several times Apply brakes at least 4 times at 20 mph (35 km/h) to clean brake rotors. Check for abnormal noise/ vibration/pulsation • Calibrate rear view mirror Calibrate rear view mirror compass to proper zone and check self-dimming function/lighting (if equipped) Driver Assistance • Verify operation of parking system Verify operation of Audi parking system sensors with rear view camera (if equipped) • Verify all vehicle Head-up Display functionality (if equipped) Verify the image can be adjusted properly in the viewing area of the windshield. Verify NAV directions, speed, cruise control, and lane assist are all visible in Head-Up Display (as equipped) Post-Road Test Inspection • Check engine oil level Fill oil to the max level when the vehicle is at operating temperature Effective 1-24-2020-US Version 1.5 Model Year 2020 | Audi Pre-Delivery Reference Document | 11 A7/S7 Technician Reference Document Vehicle Preparation Trunk Inspection • Perform any open campaigns • Install wheel bolt cover removal tool from PDI kit into trunk tool kit Follow instructions listed in campaign documentation • Perform diagnostic work Connect vehicle diagnostic tester • Select “Diagnosis” mode and start diagnosis • Perform vehicle identification • Untick “Working with Guided Fault Finding” • Switch to “Special functions” tab and select following program: Delivery Inspection total • Start program by selecting “Carry out check” • Continue to follow instructions on screen and complete the process • Switch to the “Control units” tab, press the “Guided Fault Finding” button and launch Guided Fault Finding as far as the test plan Install wheel bolt cover removal tool from PDI kit and wheel lock key (if applicable) into trunk tool kit • Set spare tire pressure See separate “Audi Normal Load Condition Tire Pressure Table” posted on ServiceNet • Check battery clamps for proper torque Refer to Elsa Pro for specification • Place one PR Number Label in the Warranty and Maintenance Book inside front cover and one on the Rear Panel Sill Frame under the luggage compartment floor, if not already there For vehicles produced prior to September 12, 2018 Labels are located in the trunk on top of spare tire Rear Panel Sill Frame location: Top Arrow • The static event memory entries must be evaluated and, if necessary, processed using Guided Fault Finding • Exit diagnosis; diagnostic log for delivery inspection is sent automatically • Install front license plate carrier (if necessary) • Retain any removed trim required for carrier installation and give to the customer. If no front license plate carrier is necessary ensure the carrier remains in the trunk for the customer Exterior • Check all key buttons and features Check functionality of all keys. Verify vehicle starts and runs with all keys and the start/stop button. Verify all doors and trunk remotely lock/unlock with all keys, including all door handle sensors with Advanced Key (if equipped) • Check all doors for proper power closing (if equipped) For vehicles equipped with the power door closing feature, check all doors for proper closing Lighting and Windshield • Test front washers (and headlight washers if equipped). Correct aim if necessary Headlights must be on to test functionality of the headlight washers Effective 1-24-2020-US Version 1.5 Model Year 2020 | Audi Pre-Delivery Reference Document | 12 A7/S7 Technician Reference Document Trunk Inspection (continued) Settings Warranty and Maintenance inside cover placement • Set Time source setting to “GPS” and set Auto daylight savings time to “on” Change time zone appropriate to the dealer location • Verify and set language and measurement units This can be changed in the Setup/Settings menu • Verify Speech Dialog System is operating Press the “Talk” button and verify several commands • Set “Music volume while parking” to medium Accessed via MMI rear view camera display, Settings > Music volume while parking (applies to vehicles with park assist or rear view camera) • Set dealership location in navigation Set dealership location for following back to dealership during road test • Turn off Manual Speed Warning (if equipped) Interior • Check operation of window, lock, and seat controls Check operation of all switches: Locks, windows, seat adjustment, heated seats and child safety features • Inspect mirrors for proper operation Inspect folding, adjustments, right side tilt in reverse, heating (if equipped) • Check rear view mirror operation Check self-dimming function/lighting (if equipped) • Verify operation of heated/ventilated and massaging seats (if equipped) Check both front and rear. Massaging feature is in the front seats only (if equipped) • Verify proper operation of climate control* Ensure proper heating and A/C cooling, open all panel vents for all zones • Inspect operation of all power outlets Inspect operation of front outlet, aux. outlet under armrest, and rear outlets • Check sunroof and sunshade operation Verify open/close/vent/deflector at edge and sunshade operation This can be changed in the Driver Assistance Settings by going to Menu > Vehicle > Driver Assistance > Speed Warning > Manual > Select Off Media / Radio / SAT • Verify HD Radio is turned “off” This can be found in the Radio/Settings Menu Audi connect® (USA ONLY) (if equipped) • Turn on the Wi-Fi® hotspot (if equipped) Ensure the wireless network is turned on (Telephone > Options > Wi-Fi® options > Wi-Fi® Mode “Hotspot” ) • Check Wi-Fi® hotspot visibility. No data available at PDI due to dealer demo mode (if equipped) Check Wi-Fi® hotspot functionality is enabled and verify the Access point (SSID) is set to “Audi_MMI_XXXX”, where XXXX is the last four digits of the VIN. Via Telephone > Options > Wi-Fi® options > Wi-Fi® Mode “Hotspot” > Hotspot settings > Access point (SSID) • Enable satellite map for navigation (if equipped) Enable satellite map in the Navigation > Gear icon > Map Settings and verify the white Google logo appears in the bottom right-hand corner of the Navigation map screen. On-Hoist Inspection • Install wheel bolt covers and center caps as supplied Wheel bolt covers can be found in the PDI kit • Inspect wheel bolts for proper torque Use torque wrench to verify Effective 1-24-2020-US Version 1.5 Model Year 2020 | Audi Pre-Delivery Reference Document | 13 A7/S7 Technician Reference Document On-Hoist Inspection (continued) • Set and store tire pressures for either sold vehicle OR stock inventory vehicle If a known “sold” unit, set to appropriate Normal Load Condition. See separate “Audi Normal Load Condition Tire Pressure Table” posted on ServiceNet. If going to stock, set to maximum recommended tire pressures listed on the B-pillar door jamb, and store tire pressure values in Car/System menu Driving Performance • Verify engine Start-Stop System functionality Verify the velum sticker is on the start/stop button. Remove the start/stop information card from the car kit and place it in the glove box with the owner’s manuals. Additional supply can be ordered via the Brand Store on AccessAudi • Verify engine performance and acceleration Listen for abnormal noise/vibrations • Test drive vehicle applying brakes several times Apply brakes at least 4 times at 20 mph (35 km/h) to clean brake rotors. Check for abnormal noise/ vibration/pulsation • Calibrate rear view mirror Calibrate rear view mirror compass to proper zone and check self-dimming function/lighting (if equipped) Driver Assistance • Verify operation of parking system Verify operation of Audi parking system sensors with rear view camera (if equipped) • Verify all vehicle Head-up display functionality (if equipped) Verify the image can be adjusted properly in the viewing area of the windshield. Verify NAV directions, speed, cruise control, and lane assist are all visible in Head-Up Display (as equipped) Post-Road Test Inspection • Check engine oil level Fill oil to the max level when the vehicle is at operating temperature Effective 1-24-2020-US Version 1.5 Model Year 2020 | Audi Pre-Delivery Reference Document | 14 A8 L/A8 e/S8 Technician Reference Document Vehicle Preparation Trunk Inspection • Perform any open campaigns • Install wheel bolt cover removal tool from PDI kit into trunk tool kit Follow instructions listed in campaign documentation • Perform diagnostic work Connect vehicle diagnostic tester • Select “Diagnosis” mode and start diagnosis • Perform vehicle identification • Untick “Working with Guided Fault Finding” • Switch to “Special functions” tab and select following program: Delivery Inspection total • Start program by selecting “Carry out check” • Continue to follow instructions on screen and complete the process Install wheel bolt cover removal tool from PDI kit and wheel lock key (if applicable) into trunk tool kit • Set spare tire pressure See separate “Audi Normal Load Condition Tire Pressure Table” posted on ServiceNet • Check battery clamps for proper torque Refer to Elsa Pro for specification Interior • Check operation of window, lock, and seat controls Check operation of all switches: Locks, windows, seat adjustment, heated seats and child safety features • Switch to the “Control units” tab, press the “Guided Fault Finding” button and launch Guided Fault Finding as far as the test plan • Inspect mirrors for proper operation • The static event memory entries must be evaluated and, if necessary, processed using Guided Fault Finding • Check rear view mirror operation • Exit diagnosis; diagnostic log for delivery inspection is sent automatically • Verify operation of heated/ventilated and massaging seats (if equipped) • Install front license plate carrier (if necessary) • Retain any removed trim required for carrier installation and give to the customer. If no front license plate carrier is necessary ensure the carrier remains in the trunk for the customer Exterior • Check all key buttons and features Check functionality of all keys. Verify vehicle starts and runs with all keys and the start/stop button. Verify all doors and trunk remotely lock/unlock with all keys, including all door handle sensors with Advanced Key (if equipped) • Check all doors for proper power closing For vehicles equipped with the power door closing feature, check all doors for proper closing Lighting and Windshield • Test front washers (and headlight washers if equipped). Correct aim if necessary Headlights must be on to test functionality of the headlight washers Effective 1-24-2020-US Version 1.5 Inspect folding, adjustments, right side tilt in reverse, heating (if equipped) Check self-dimming function/lighting (if equipped) Check both front and rear. Massaging feature is in the front seats only (if equipped) • Verify proper operation of climate control Ensure proper heating and A/C cooling, open all panel vents for all zones • Inspect operation of all power outlets Inspect operation of front outlet, aux. outlet under armrest, and rear outlets • Check panoramic sunroof and sunshade operation Verify open/close/vent/deflector at edge and sunshade operation Settings • Set Time source setting to “GPS” and set Auto daylight savings time to “on” Change time zone appropriate to the dealer location • Verify and set language and measurement units This can be changed in the Setup/Settings menu • Verify Speech Dialog System is operating Press the “Talk” button and verify several commands Model Year 2020 | Audi Pre-Delivery Reference Document | 15 A8 L/A8 e/S8 Technician Reference Document Settings (continued) Driving Performance • Set “Music volume while parking” to medium • Verify engine Start-Stop System functionality Accessed via MMI rear view camera display, Settings > Music volume while parking (applies to vehicles with park assist or rear view camera) • Set dealership location in navigation (if equipped) Set dealership location for following back to dealership during road test • Turn off Manual Speed Warning (if equipped) This can be changed in the Driver Assistance Settings by going to Menu > Vehicle > Driver Assistance > Speed Warning > Manual > Select Off Media / Radio / SAT • Verify HD Radio is turned “off” This can be found in the Radio/Settings Menu Audi connect® (USA ONLY) • Turn on the Wi-Fi® hotspot (if equipped) Ensure the wireless network is turned on (Telephone > Options > Wi-Fi® options > Wi-Fi® Mode “Hotspot” ) • Check Wi-Fi® hotspot visibility. No data available at PDI due to dealer demo mode (if equipped) Check Wi-Fi® hotspot functionality is enabled and verify the Access point (SSID) is set to “Audi_MMI_XXXX”, where XXXX is the last four digits of the VIN. Via Telephone > Options > Wi-Fi® options > Wi-Fi® Mode “Hotspot” > Hotspot settings > Access point (SSID) • Enable satellite map for navigation (if equipped) Enable satellite map in the Navigation > Gear icon > Map Settings and verify the white Google logo appears in the bottom right-hand corner of the Navigation map screen. Verify the velum sticker is on the start/stop button. Remove the start/stop information card from the car kit and place it in the glove box with the owner’s manuals. Additional supply can be ordered via the Brand Store on AccessAudi • Verify engine performance and acceleration Listen for abnormal noise/vibrations • Test drive vehicle applying brakes several times Apply brakes at least 4 times at 20 mph (35 km/h) to clean brake rotors. Check for abnormal noise/ vibration/pulsation • Calibrate rear view mirror Calibrate rear view mirror compass to proper zone and check self-dimming function/lighting (if equipped) Driver Assistance • Verify operation of parking system Verify operation of Audi parking system sensors with rear view camera (if equipped) • Verify all vehicle Head-up display functionality (if equipped) Verify the image can be adjusted properly in the viewing area of the windshield. Verify NAV directions, speed, cruise control, and lane assist are all visible in Head-Up Display (as equipped) Post-Road Test Inspection • Check engine oil level Fill oil to the max level when the vehicle is at operating temperature On-Hoist Inspection • Install wheel bolt covers and center caps as supplied Wheel bolt covers can be found in the PDI kit • Inspect wheel bolts for proper torque Use torque wrench to verify • Set and store tire pressures for either sold vehicle OR stock inventory vehicle If a known “sold” unit, set to appropriate Normal Load Condition. See separate “Audi Normal Load Condition Tire Pressure Table” posted on ServiceNet. If going to stock, set to maximum recommended tire pressures listed on the B-pillar door jamb, and store tire pressure values in Car/System menu Effective 1-24-2020-US Version 1.5 Model Year 2020 | Audi Pre-Delivery Reference Document | 16 e-tron Technician Reference Document Vehicle Preparation Trunk Inspection • Perform any open campaigns • Install wheel bolt cover removal tool from PDI kit into trunk tool kit Follow instructions listed in campaign documentation • Perform diagnostic work Connect vehicle diagnostic tester Install wheel bolt cover removal tool from PDI kit and wheel lock key (if applicable) into trunk tool kit • Select “Diagnosis” mode and start diagnosis Interior • Perform vehicle identification • Check operation of window, lock, and seat controls • Untick “Working with Guided Fault Finding” • Switch to “Special functions” tab and select following program: Delivery Inspection total • Start program by selecting “Carry out check” • Continue to follow instructions on screen and complete the process • Switch to the “Control units” tab, press the “Guided Fault Finding” button and launch Guided Fault Finding as far as the test plan • The static event memory entries must be evaluated and, if necessary, processed using Guided Fault Finding • Exit diagnosis; diagnostic log for delivery inspection is sent automatically • Install front license plate carrier (if necessary) • Retain any removed trim required for carrier installation and give to the customer. If no front license plate carrier is necessary ensure the carrier remains in the trunk for the customer Exterior • Check all key buttons and features Check functionality of all keys. Verify vehicle starts and runs with all keys and the start/stop button. Verify all doors and trunk remotely lock/unlock with all keys, including all door handle sensors with Advanced Key (if equipped) • Check all doors for proper power closing For vehicles equipped with the power door closing feature, check all doors for proper closing Lighting and Windshield • Test front washers (and headlight washers if equipped). Correct aim if necessary Headlights must be on to test functionality of the headlight washers Effective 1-24-2020-US Version 1.5 Check operation of all switches: Locks, windows, seat adjustment, heated seats and child safety features • Inspect mirrors for proper operation Inspect folding, adjustments, right side tilt in reverse, heating (if equipped) • Check rear view mirror operation Check self-dimming function/lighting (if equipped) • Verify operation of heated/ventilated and massaging seats (front/rear) (if equipped) Check both front and rear. Massaging feature is in the front seats only (if equipped) • Verify proper operation of climate control Ensure proper heating and A/C cooling, open all panel vents for all zones • Inspect operation of all power outlets Inspect operation of front outlet, aux. outlet under armrest, and rear outlets • Check panoramic sunroof and sunshade operation Verify open/close/vent/deflector at edge and sunshade operation Settings • Set Time source setting to “GPS” and set Auto daylight savings time to “on” Change time zone appropriate to the dealer location • Verify and set language and measurement units This can be changed in the Setup/Settings menu: Home > Settings > General > Measurement Units > Consumption (electric motor) to mi/kWh, and check to ensure all other units are set to US specs • Verify Speech Dialog System is operating Press the “Talk” button and verify several commands • Set “Music volume while parking” to medium Accessed via MMI rear view camera display, Settings > Music volume while parking (applies to vehicles with park assist or rear view camera) Model Year 2020 | Audi Pre-Delivery Reference Document | 17 e-tron Technician Reference Document Settings (continued) Driving Performance • Set dealership location in navigation (if equipped) • Verify electric motor performance and acceleration Set dealership location for following back to dealership during road test • Turn off Manual Speed Warning (if equipped) This can be changed in the Driver Assistance Settings by going to Menu > Vehicle > Driver Assistance > Speed Warning > Manual > Select Off • Disable climate control via door unlock Main screen => Vehicle => Climate control => select small temperature gauge symbol in upper right section => settings (“wheel” upper right) => unselect (disable) “Start A/C after unlocking”. Check and adjust, if needed. Button position “off”, in left position. Media / Radio / SAT • Verify HD Radio is turned “off” This can be found in the Radio/Settings Menu Audi connect® (USA ONLY) (if equipped) • Turn on the Wi-Fi® hotspot (if equipped) Listen for abnormal noise/vibrations • Test drive vehicle applying brakes several times Apply brakes at least 4 times at 20 mph (35 km/h) to clean brake rotors. Check for abnormal noise/ vibration/pulsation • Calibrate rear view mirror Calibrate rear view mirror compass to proper zone and check self-dimming function/lighting (if equipped) Driver Assistance • Verify operation of parking system Verify operation of Audi parking system sensors with rear view camera (if equipped) • Verify all vehicle Head-up display functionality (if equipped) Verify the image can be adjusted properly in the viewing area of the windshield. Verify NAV directions, speed, cruise control, and lane assist are all visible in Head-Up Display (as equipped) Ensure the wireless network is turned on (Telephone > Options > Wi-Fi® options > Wi-Fi® Mode “Hotspot” ) • Check Wi-Fi® hotspot visibility. No data available at PDI due to dealer demo mode Check Wi-Fi® hotspot functionality is enabled and verify the Access point (SSID) is set to “Audi_MMI_XXXX”, where XXXX is the last four digits of the VIN. Via Telephone > Options > Wi-Fi® options > Wi-Fi® Mode “Hotspot” > Hotspot settings > Access point (SSID) • Enable satellite map for navigation Enable satellite map in the Navigation > Gear icon > Map Settings and verify the white Google logo appears in the bottom right-hand corner of the Navigation map screen. On-Hoist Inspection • Inspect wheel bolts for proper torque Use torque wrench to verify • Install wheel bolt covers and center caps as supplied Wheel bolt covers can be found in the PDI kit • Set and store tire pressures for either sold vehicle OR stock inventory vehicle If a known “sold” unit, set to appropriate Normal Load Condition. See separate “Audi Normal Load Condition Tire Pressure Table” posted on ServiceNet. If going to stock, set to maximum recommended tire pressures listed on the B-pillar door jamb, and store tire pressure values in Car/System menu Effective 1-24-2020-US Version 1.5 Model Year 2020 | Audi Pre-Delivery Reference Document | 18 Q3 Technician Reference Document Vehicle Preparation Trunk Inspection • Perform any open campaigns • Verify power tailgate is operational and set default opening height Follow instructions listed in campaign documentation • Perform diagnostic work Connect vehicle diagnostic tester • Select “Diagnosis” mode and start diagnosis • Perform vehicle identification • Untick “Working with Guided Fault Finding” • Switch to “Special functions” tab and select following program: Delivery Inspection total • Start program by selecting “Carry out check” • Continue to follow instructions on screen and complete the process • Switch to the “Control units” tab, press the “Guided Fault Finding” button and launch Guided Fault Finding as far as the test plan • The static event memory entries must be evaluated and, if necessary, processed using Guided Fault Finding • Exit diagnosis; diagnostic log for delivery inspection is sent automatically • Install front license plate carrier (if necessary) • Retain any removed trim required for carrier installation and give to the customer. If no front license plate carrier is necessary ensure the carrier remains in the trunk for the customer Exterior • Check all key buttons and features Check functionality of all keys. Verify vehicle starts and runs with all keys and the start/stop button. Verify all doors and trunk manually and remotely lock/unlock with all keys, including all door handle sensors with Advanced Key (if equipped) Lighting and Windshield • Test front washers (and headlight washers if equipped). Correct aim if necessary Headlights must be on to test functionality of the headlight washers Adjust the trunk lid opening height to 77.7 inches (197 cm) from the ground to the close button in the rear lid. Press and hold the close button in the rear lid for at least four seconds to program the opening height • Install wheel bolt cover removal tool from PDI kit into trunk lid tool kit Install wheel bolt cover removal tool from PDI kit and wheel lock key (if applicable) into trunk tool kit to the right of the spare tire • Set spare tire pressure See separate “Audi Normal Load Condition Tire Pressure Table” posted on ServiceNet • Check battery clamps for proper torque Refer to Elsa Pro for specification Interior • Check operation of window, lock, and seat controls Check operation of all switches: Locks, windows, seat adjustment, heated seats (if equipped) and child safety features • Inspect mirrors for proper operation Inspect folding, adjustments, right side tilt in reverse, heating (if equipped) • Check rear view mirror operation Check self-dimming function/lighting (if equipped) • Verify proper operation of climate control Ensure proper heating and A/C cooling and open all panel vents • Inspect operation of all power outlets Inspect operation of front outlet, aux. outlet under armrest, and rear outlets • Check panoramic sunroof and sunshade operation Verify open/close/vent/deflector at edge and sunshade operation Settings • Set Time source setting to “GPS” and set Auto daylight savings time to “on.” (if equipped with navigation) Change time zone appropriate to the dealer location Effective 1-24-2020-US Version 1.5 Model Year 2020 | Audi Pre-Delivery Reference Document | 19 Q3 Technician Reference Document Settings (continued) Driving Performance • Set “Entertain. Fad.” in Parking aid to an audible level (if equipped) • Verify engine Start-Stop System functionality Via “ Menu > Vehicle > Left Option > Drive Assistance > Parking Aid” • Verify and set language and measurement units This can be changed in the Setup/Settings menu • Verify Speech Dialog System is operating Press the “Talk” button and verify several commands • Set dealership location in navigation (if equipped) Set dealership location for following back to dealership during road test Media / Radio / SAT • Verify HD Radio is turned “off” This can be found in the Radio/Settings Menu Audi connect® (USA ONLY) (if equipped) • Turn on the Wi-Fi® hotspot (if equipped) Ensure the wireless network is turned on (Telephone > Right Option > Wi-Fi® options > Wi-Fi® “On”) • Check Wi-Fi® hotspot visibility. No data available at PDI (if equipped) Check Wi-Fi® hotspot functionality is enabled and verify the SSID is set to “AUDIXXXXX”, where XXXXX = the last five digits of VIN that are automatically preset in the system Verify the velum sticker is on the start/stop button. Remove the start/stop information card from the car kit and place it in the glove box with the owner’s manuals. Additional supply can be ordered via the Brand Store on AccessAudi • Verify engine performance and acceleration Listen for abnormal noise/vibrations • Test drive vehicle applying brakes several times Apply brakes at least 4 times at 20 mph (35 km/h) to clean brake rotors. Check for abnormal noise/ vibration/pulsation • Calibrate rear view mirror Calibrate rear view mirror compass to proper zone and check self-dimming function/lighting (if equipped) Driver Assistance • Verify operation of parking system plus with rear cross traffic assist (if equipped) Verify operation of Audi parking system sensors with rear view camera Post-Road Test Inspection • Check engine oil level Fill oil to the max level when the vehicle is at operating temperature • Enable satellite map for navigation (if equipped) Enable Google Earth view in the Navigation > Map Settings and verify the white Google logo appears in the bottom right-hand corner of the MMI screen next to the LTE symbol. On-Hoist Inspection On-Hoist Inspection • Install wheel bolt covers and center caps as supplied Wheel bolt covers and center caps can be found in the PDI kit • Inspect wheel bolts for proper torque Use torque wrench to verify • Set and store tire pressures for either sold vehicle OR stock inventory vehicle. See separate “Audi Normal Load Condition Tire Pressure Table” posted on ServiceNet If a known “sold” unit, set to appropriate Normal Load Condition. See separate “Audi Normal Load Condition Tire Pressure Table” posted on ServiceNet. If going to stock, set to maximum recommended tire pressures listed on the B-pillar door jamb, and store tire pressure values in Car/System menu Effective 1-24-2020-US Version 1.5 Model Year 2020 | Audi Pre-Delivery Reference Document | 20 Q5/Q5 e/SQ5 Technician Reference Document Vehicle Preparation Exterior (continued) • Set adaption channel to enable CD Ripping using Guided Functions (if equipped with NAV) • Prepare the base bars for customer delivery (install bars only upon customer request) Set adaptation channel (via Special functions > Service work > 5F-Activating/deactivating storage of music). Also referred to as CD Ripping. Perform 3 button reset of the MMI to complete the activation. Refer to the owner’s manual for model-specific button sequence • Perform any open campaigns Follow instructions listed in campaign documentation • Perform diagnostic work Install the rubber strips to the top of the base carrier bars (do not install the carrier bars on the vehicle unless customer has requested). Repackage the bars into the box if they are not being installed on the vehicle. Retrieve the paper with the torque wrench key code from the base carrier bar box. Insert the paper with the key code into the owner’s literature wallet. Record torque wrench key code in the VDF to ensure it’s documented in the event the paper with the code is misplaced Connect vehicle diagnostic tester • Select “Diagnosis” mode and start diagnosis • Perform vehicle identification • Untick “Working with Guided Fault Finding” • Switch to “Special functions” tab and select following program: Delivery Inspection total • Start program by selecting “Carry out check” • Continue to follow instructions on screen and complete the process • Switch to the “Control units” tab, press the “Guided Fault Finding” button and launch Guided Fault Finding as far as the test plan • The static event memory entries must be evaluated and, if necessary, processed using Guided Fault Finding • Exit diagnosis; diagnostic log for delivery inspection is sent automatically • Install front license plate carrier (if necessary) • Retain any removed trim required for carrier installation and give to the customer. If no front license plate carrier is necessary ensure the carrier remains in the trunk for the customer Lighting and Windshield • Test front washers (and headlight washers if equipped). Correct aim if necessary Headlights must be on to test functionality of the headlight washers Trunk Inspection • Verify power tailgate is operational and set default opening height Adjust the trunk lid opening height to 77.7 inches (197 cm) from the ground to the close button in the rear lid. Press and hold the close button in the rear lid for at least four seconds to program the opening height • Install wheel bolt cover removal tool from PDI kit into trunk lid toolkit Install wheel bolt cover removal tool from PDI kit and wheel lock key (if applicable) into trunk tool kit to the right of the spare tire • Set spare tire pressure See separate “Audi Normal Load Condition Tire Pressure Table” posted on ServiceNet • Check battery clamps for proper torque Refer to Elsa Pro for specification Exterior Interior • Check all key buttons and features • Check operation of window, lock, and seat controls Check functionality of all keys. Verify vehicle starts and runs with all keys and the start/stop button. Verify all doors and trunk manually and remotely lock/unlock with all keys, including all door handle sensors with Advanced Key (if equipped) • Check all doors for proper power closing (if equipped) For vehicles equipped with the power door closing feature, check all doors for proper closing Effective 1-24-2020-US Version 1.5 Check operation of all switches: Locks, windows, seat adjustment, heated seats (if equipped) and child safety features • Inspect mirrors for proper operation Inspect folding, adjustments, right side tilt in reverse, heating (if equipped) • Check rear view mirror operation Check self-dimming function/lighting (if equipped) Model Year 2020 | Audi Pre-Delivery Reference Document | 21 Q5/Q5 e/SQ5 Technician Reference Document Interior (continued) Audi connect® (USA ONLY) (if equipped) (continued) • Verify proper operation of climate control • Check Wi-Fi® hotspot visibility. No data available at PDI (if equipped) Check Wi-Fi® hotspot functionality is enabled and verify the SSID is set to “AUDIXXXXX”, where XXXXX = the last five digits of VIN that are automatically preset in the system Ensure proper heating and A/C cooling and open all panel vents • Inspect operation of all power outlets Inspect operation of front outlet, aux. outlet under armrest, and rear outlets • Check panoramic sunroof and sunshade operation Verify open/close/vent/deflector at edge and sunshade operation Settings • Set Time source setting to “GPS” and set Auto daylight savings time to “on.” Change time zone appropriate to the dealer location • Verify and set language and measurement units This can be changed in the Setup/Settings menu • Verify Speech Dialog System is operating Press the “Talk” button and verify several commands • Set “Entertain. Fad.” in Parking aid to an audible level Via “ Menu > Vehicle > Left Option > Drive Assistance > Parking Aid” • Set “Music volume while parking” to 6 lines Accessed via MMI rear view camera display, Settings > Music volume while parking (applies to vehicles with park assist or rear view camera) • Set dealership location in navigation (if equipped) Set dealership location for following back to dealership during road test • Turn off Manual Speed Warning (if equipped) This can be changed in the Driver Assistance settings by going to Menu > Vehicle > Driver Assistance > Speed Warning > Manual->Select Off Media / Radio / SAT • Verify HD Radio is turned “off” This can be found in the Radio/Settings Menu Audi connect® (USA ONLY) (if equipped) • Turn on the Wi-Fi® hotspot (if equipped) Ensure the wireless network is turned on (Telephone > Right Option > Wi-Fi® options > Wi-Fi® “On”) Effective 1-24-2020-US Version 1.5 • Enable Google Earth view for navigation (if equipped) Enable Google Earth view in the Navigation > Map Settings and verify the white Google logo appears in the bottom righthand corner of the MMI screen next to the LTE symbol. On-Hoist Inspection • Install wheel bolt covers and center caps as supplied Wheel bolt covers and center caps can be found in the PDI kit • Inspect wheel bolts for proper torque Use torque wrench to verify • Set and store tire pressures for either sold vehicle OR stock inventory vehicle (See separate “Audi Normal Load Condition Tire Pressure Table” posted on ServiceNet) If a known “sold” unit, set to appropriate Normal Load Condition. See separate “Audi Normal Load Condition Tire Pressure Table” posted on ServiceNet. If going to stock, set to maximum recommended tire pressures listed on the B-pillar door jamb, and store tire pressure values in Car/System menu Driving Performance • Verify engine Start-Stop System functionality Verify the velum sticker is on the start/stop button. Remove the start/stop information card from the car kit and place it in the glove box with the owner’s manuals. Additional supply can be ordered via the Brand Store on AccessAudi • Verify engine performance and acceleration Listen for abnormal noise/vibrations • Test drive vehicle applying brakes several times Apply brakes at least 4 times at 20 mph (35 km/h) to clean brake rotors. Check for abnormal noise/ vibration/pulsation • Calibrate rear view mirror Calibrate rear view mirror compass to proper zone and check self-dimming function/lighting (if equipped) Driver Assistance • Verify operation of parking system (if equipped) Verify operation of Audi parking system sensors with rear view camera (if equipped) Model Year 2020 | Audi Pre-Delivery Reference Document | 22 Q5/Q5 e/SQ5 Technician Reference Document Driver Assistance (continued) • Verify all vehicle Head-up display functionality (if equipped) Verify the image can be adjusted properly in the viewing area of the windshield. Verify NAV directions, speed, cruise control, and lane assist are all visible in Head-Up Display (as equipped) Post-Road Test Inspection • Check engine oil level Fill oil to the max level when the vehicle is at operating temperature Effective 1-24-2020-US Version 1.5 Model Year 2020 | Audi Pre-Delivery Reference Document | 23 Q7/SQ7 Technician Reference Document Vehicle Preparation Trunk Inspection • Perform any open campaigns • Verify power tailgate is operational and set to maximum opening height (if equipped) Follow instructions listed in campaign documentation • Perform diagnostic work Connect vehicle diagnostic tester • Select “Diagnosis” mode and start diagnosis • Perform vehicle identification • Untick “Working with Guided Fault Finding” • Switch to “Special functions” tab and select following program: Delivery Inspection total • Start program by selecting “Carry out check” • Continue to follow instructions on screen and complete the process • Switch to the “Control units” tab, press the “Guided Fault Finding” button and launch Guided Fault Finding as far as the test plan • The static event memory entries must be evaluated and, if necessary, processed using Guided Fault Finding • Exit diagnosis; diagnostic log for delivery inspection is sent automatically • Install front license plate carrier (if necessary) • Retain any removed trim required for carrier installation and give to the customer. If no front license plate carrier is necessary ensure the carrier remains in the trunk for the customer Exterior • Check all key buttons and features Check functionality of all keys. Verify vehicle starts and runs with all keys and the start/stop button. Verify all doors and trunk manually and remotely lock/unlock with all keys, including all door handle sensors with Advanced Key (if equipped) • Check all doors for proper power closing (if equipped) For vehicles equipped with the power door closing feature, check all doors for proper closing Lighting and Windshield • Test front washers (and headlight washers if equipped). Correct aim if necessary Headlights must be on to test functionality of the headlight washers Effective 1-24-2020-US Version 1.5 Press and hold the close button in the rear lid for at least four seconds to program the opening height. Verify operation of handsfree release (if equipped) • Install wheel bolt cover removal tool from PDI kit into trunk lid toolkit Install wheel bolt cover removal tool from PDI kit and wheel lock key (if applicable) into trunk tool kit to the right of the spare tire • Check battery clamps for proper torque Refer to Elsa Pro for specification Interior • Check operation of window, lock, and seat controls Check operation of all switches: Locks, windows, seat adjustment, heated seats (if equipped) and child safety features • Inspect mirrors for proper operation Inspect folding, adjustments, right side tilt in reverse, heating (if equipped) and child safety features • Check rear view mirror operation Check self-dimming function/lighting (if equipped) • Verify operation of heated/ventilated and massaging seats (if equipped) Check both front and rear. Massaging feature is in the front seats only (if equipped) • Verify operation of manual folding 2nd row and power folding 3rd row seats Controls for the power folding 3rd row are located in the trunk • Verify proper operation of climate control Ensure proper heating and A/C cooling and open all panel vents • Inspect operation of all power outlets Inspect operation of front outlet, aux. outlet under armrest, and rear outlets • Check panoramic sunroof and sunshade operation Verify open/close/vent/deflector at edge and sunshade operation Settings • Verify and set language and measurement units This can be changed in the Setup/Settings menu Model Year 2020 | Audi Pre-Delivery Reference Document | 24 Q7/SQ7 Technician Reference Document Settings (continued) On-Hoist Inspection (continued) • Verify Speech Dialog System is operating • Set and store tire pressures for either sold vehicle OR stock inventory vehicle (See separate “Audi Normal Load Condition Tire Pressure Table” posted on ServiceNet) If a known “sold” unit, set to appropriate Normal Load Condition. See separate “Audi Normal Load Condition Tire Pressure Table” posted on ServiceNet. If going to stock, set to maximum recommended tire pressures listed on the B-pillar door jamb, and store tire pressure values in Car/System menu Press the “Talk” button and verify several commands • Set “Entertain. Fad.” in Parking aid to an audible level Via “ Menu > Vehicle > Left Option > Drive Assistance > Parking Aid” • Set “Music volume while parking” to medium Accessed via MMI rear view camera display, Settings > Music volume while parking (applies to vehicles with park assist or rear view camera) • Set dealership location in navigation (if equipped) Set dealership location for following back to dealership during road test • Turn off Manual Speed Warning (if equipped) This can be changed in the Driver Assistance settings by going to Menu > Vehicle > Driver Assistance > Speed Warning > Manual >Select Off Media / Radio / SAT • Verify HD Radio is turned “off” This can be found in the Radio/Settings Menu Audi connect® (USA ONLY) (if equipped) • Turn on the Wi-Fi® hotspot (if equipped) Ensure the wireless network is turned on (Telephone > Right Option > Wi-Fi® options > Wi-Fi® “On”) • Check Wi-Fi® hotspot visibility. No data available at PDI (if equipped) Check Wi-Fi® hotspot functionality is enabled and verify the SSID is set to “AUDIXXXXX”, where XXXXX = the last five digits of VIN that are automatically preset in the system • Enable Google Earth view for navigation (if equipped) Enable Google Earth view in the Navigation > Map Settings and verify the white Google logo appears in the bottom righthand corner of the MMI screen next to the LTE symbol On-Hoist Inspection Driving Performance • Verify engine Start-Stop System functionality Verify the velum sticker is on the start/stop button. Remove the start/stop information card from the car kit and place it in the glove box with the owner’s manuals. Additional supply can be ordered via the Brand Store on AccessAudi • Verify engine performance and acceleration Listen for abnormal noise/vibrations • Test drive vehicle applying brakes several times Apply brakes at least 4 times at 20 mph (35 km/h) to clean brake rotors. Check for abnormal noise/ vibration/pulsation • Calibrate rear view mirror Calibrate rear view mirror compass to proper zone and check self-dimming function/lighting (if equipped) Driver Assistance • Verify operation of parking system Verify operation of Audi parking system sensors with rear view camera (if equipped) • Verify all vehicle Head-up display functionality (if equipped) Verify the image can be adjusted properly in the viewing area of the windshield. Verify NAV directions, speed, cruise control, and lane assist are all visible in Head-Up Display (as equipped) Post-Road Test Inspection • Check engine oil level Fill oil to the max level when the vehicle is at operating temperature • Install wheel bolt covers and center caps as supplied Wheel bolt covers and center caps can be found in the PDI kit • Inspect wheel bolts for proper torque Use torque wrench to verify Effective 1-24-2020-US Version 1.5 Model Year 2020 | Audi Pre-Delivery Reference Document | 25 Q8/SQ8/RS Q8 Technician Reference Document Vehicle Preparation Trunk Inspection • Perform any open campaigns • Verify power tailgate is operational and set to maximum opening height (if equipped) Follow instructions listed in campaign documentation • Perform diagnostic work Connect vehicle diagnostic tester • Select “Diagnosis” mode and start diagnosis • Perform vehicle identification • Untick “Working with Guided Fault Finding” • Switch to “Special functions” tab and select following program: Delivery Inspection total • Start program by selecting “Carry out check” • Continue to follow instructions on screen and complete the process • Switch to the “Control units” tab, press the “Guided Fault Finding” button and launch Guided Fault Finding as far as the test plan • The static event memory entries must be evaluated and, if necessary, processed using Guided Fault Finding • Exit diagnosis; diagnostic log for delivery inspection is sent automatically • Install front license plate carrier (if necessary) • Retain any removed trim required for carrier installation and give to the customer. If no front license plate carrier is necessary ensure the carrier remains in the trunk for the customer Exterior • Check all key buttons and features Check functionality of all keys. Verify vehicle starts and runs with all keys and the start/stop button. Verify all doors and trunk manually and remotely lock/unlock with all keys, including all door handle sensors with Advanced Key (if equipped) • Check all doors for proper power closing (if equipped) For vehicles equipped with the power door closing feature, check all doors for proper closing Lighting and Windshield • Test front washers (and headlight washers if equipped). Correct aim if necessary Headlights must be on to test functionality of the headlight washers Effective 1-24-2020-US Version 1.5 Press and hold the close button in the rear lid for at least four seconds to program the opening height. Verify operation of handsfree release (if equipped) • Install wheel bolt cover removal tool from PDI kit into trunk lid toolkit Install wheel bolt cover removal tool from PDI kit and wheel lock key (if applicable) into trunk tool kit to the right of the spare tire • Check battery clamps for proper torque Refer to Elsa Pro for specification • Set spare tire pressure See separate “Audi Normal Load Condition Tire Pressure Table” posted on ServiceNet Interior • Check operation of window, lock, and seat controls Check operation of all switches: Locks, windows, seat adjustment, heated seats (if equipped) and child safety features • Inspect mirrors for proper operation Inspect folding, adjustments, right side tilt in reverse, heating (if equipped) and child safety features • Check rear view mirror operation Check self-dimming function/lighting (if equipped) • Verify operation of heated/ventilated and massaging seats (if equipped) Check both front and rear. Massaging feature is in the front seats only (if equipped) • Verify proper operation of climate control Ensure proper heating and A/C cooling and open all panel vents • Inspect operation of all power outlets Inspect operation of front outlet, aux. outlet under armrest, and rear outlets • Check panoramic sunroof and sunshade operation Verify open/close/vent/deflector at edge and sunshade operation Settings • Set Time source setting to “GPS” and set Auto daylight savings time to “on.” Change time zone appropriate to the dealer location Model Year 2020 | Audi Pre-Delivery Reference Document | 26 Q8/SQ8/RS Q8 Technician Reference Document Settings (continued) On-Hoist Inspection (continued) • Verify and set language and measurement units • Set and store tire pressures for either sold vehicle OR stock inventory vehicle (See separate “Audi Normal Load Condition Tire Pressure Table” posted on ServiceNet) This can be changed in the Setup/Settings menu • Verify Speech Dialog System is operating Press the “Talk” button and verify several commands • Set “Music volume while parking” to medium Accessed via MMI rear view camera display, Settings > Music volume while parking (applies to vehicles with park assist or rear view camera) • Set dealership location in navigation Set dealership location for following back to dealership during road test • Turn off Manual Speed Warning (if equipped) This can be changed in the Driver Assistance settings by going to Menu > Vehicle > Driver Assistance > Speed Warning > Manual >Select Off If a known “sold” unit, set to appropriate Normal Load Condition. See separate “Audi Normal Load Condition Tire Pressure Table” posted on ServiceNet. If going to stock, set to maximum recommended tire pressures listed on the B-pillar door jamb, and store tire pressure values in Car/System menu Driving Performance • Verify engine Start-Stop System functionality Verify the velum sticker is on the start/stop button. Remove the start/stop information card from the car kit and place it in the glove box with the owner’s manuals. Additional supply can be ordered via the Brand Store on AccessAudi • Verify engine performance and acceleration Listen for abnormal noise/vibrations Media / Radio / SAT • Verify HD Radio is turned “off” This can be found in the Radio/Settings Menu • Test drive vehicle applying brakes several times Apply brakes at least 4 times at 20 mph (35 km/h) to clean brake rotors. Check for abnormal noise/ vibration/pulsation • Calibrate rear view mirror Audi connect® (USA ONLY) (if equipped) • Turn on the Wi-Fi® hotspot (if equipped) Ensure the wireless network is turned on (Telephone > Options > Wi-Fi® options > Wi-Fi® Mode “Hotspot” ) • Check Wi-Fi® hotspot visibility. No data available at PDI due to dealer demo mode (if equipped) Check Wi-Fi® hotspot functionality is enabled and verify the Access point (SSID) is set to “Audi_MMI_XXXX”, where XXXX is the last four digits of the VIN. Via Telephone > Options > Wi-Fi® options > Wi-Fi® Mode “Hotspot” > Hotspot settings > Access point (SSID) • Enable satellite map for navigation (if equipped) Enable satellite map in the Navigation > Gear icon > Map Settings and verify the white Google logo appears in the bottom right-hand corner of the Navigation map screen. On-Hoist Inspection • Install wheel bolt covers and center caps as supplied Calibrate rear view mirror compass to proper zone and check self-dimming function/lighting (if equipped) Driver Assistance • Verify operation of parking system Verify operation of Audi parking system sensors with rear view camera (if equipped) • Verify all vehicle Head-up display functionality (if equipped) Verify the image can be adjusted properly in the viewing area of the windshield. Verify NAV directions, speed, cruise control, and lane assist are all visible in Head-Up Display (as equipped) Post-Road Test Inspection • Check engine oil level Fill oil to the max level when the vehicle is at operating temperature Wheel bolt covers and center caps can be found in the PDI kit • Inspect wheel bolts for proper torque Use torque wrench to verify Effective 1-24-2020-US Version 1.5 Model Year 2020 | Audi Pre-Delivery Reference Document | 27 R8 Coupe & Spyder Technician Reference Document Vehicle Preparation Lighting and Windshield • Set adaption channel to enable CD Ripping using Guided Functions (if equipped with NAV) • Test front washers (and headlight washers if equipped). Correct aim if necessary Set adaptation channel (via Special functions > Service work > 5F-Activating/deactivating storage of music). Also referred to as CD Ripping. Perform 3 button reset of the MMI to complete the activation. Refer to the owner’s manual for model-specific button sequence • Perform any open campaigns Follow instructions listed in campaign documentation • Perform diagnostic work Connect vehicle diagnostic tester • Select “Diagnosis” mode and start diagnosis • Perform vehicle identification • Untick “Working with Guided Fault Finding” • Switch to “Special functions” tab and select following program: Delivery Inspection total • Start program by selecting “Carry out check” • Continue to follow instructions on screen and complete the process • Switch to the “Control units” tab, press the “Guided Fault Finding” button and launch Guided Fault Finding as far as the test plan • The static event memory entries must be evaluated and, if necessary, processed using Guided Fault Finding • Exit diagnosis; diagnostic log for delivery inspection is sent automatically • Install front license plate carrier (if necessary) • Retain any removed trim required for carrier installation and give to the customer. If no front license plate carrier is necessary ensure the carrier remains in the trunk for the customer Exterior • Check all key buttons and features Check functionality of all keys. Verify vehicle starts and runs with all keys and the start/stop button. Verify all doors and trunk remotely lock/unlock with all keys, including all door handle sensors with Advanced Key (if equipped) Headlights must be on to test functionality of the headlight washers Trunk Inspection • Install wheel bolt cover removal tool from PDI kit into trunk tool kit Install wheel bolt cover removal tool from PDI kit and wheel lock key (if applicable) into trunk tool kit • Check battery clamps for proper torque Refer to Elsa Pro for specification Interior • Check operation of window, lock, and seat controls Check operation of all switches: Locks, windows, seat adjustment, heated seats (if equipped) and child safety features • Inspect mirrors for proper operation Inspect folding, adjustments, right side tilt in reverse, heating • Check rear view mirror operation Check self-dimming function/lighting (if equipped) • Verify proper operation of climate control Ensure proper heating and A/C cooling and open all panel vents for all zones • Inspect operation of all power outlets Inspect operation of front outlet, aux. outlet under armrest, and rear outlets Settings • Set Time source setting to “GPS” and set Auto daylight savings time to “on.” Change time zone appropriate to the dealer location • Verify and set language and measurement units This can be changed in the Settings menu by going to Menu > Vehicle > Vehicle settings • Verify Speech Dialog System is operating Press the “Talk” button and verify several commands • Set “Entertain. Fad.” in Parking aid to an audible level Via “Menu > Vehicle > Left Option > Driver Assistance > Parking Aid” • Set dealership location in navigation (if equipped) Set dealership location for following back to dealership during road test Effective 1-24-2020-US Version 1.5 Model Year 2020 | Audi Pre-Delivery Reference Document | 28 R8 Coupe & Spyder Technician Reference Document Settings (continued) Driving Performance (continued) • Turn off Manual Speed Warning (if equipped) • Calibrate rear view mirror This can be changed in the Driver Assistance settings by going to Menu > Vehicle > Driver Assistance > Speed Warning > Manual->Select Off Calibrate rear view mirror compass to proper zone and check self-dimming function/lighting (if equipped) Driver Assistance Media / Radio / SAT • Verify HD Radio is turned “off” This can be found in the Radio/Settings Menu • Verify operation of Audi parking system plus Verify operation of Audi parking system sensors with rear view camera Audi connect® (USA ONLY) (if equipped) Convertible Functionality (if equipped) • Turn on the Wi-Fi hotspot (if equipped) • Test operation of power folding top ® Ensure the wireless network is turned on (Telephone > Options > Wi-Fi® options > Wi-Fi® Mode “Hotspot” ) • Check Wi-Fi® hotspot visibility. No data available at PDI due to dealer demo mode (if equipped) Check Wi-Fi® hotspot functionality is enabled and verify the Access point (SSID) is set to “Audi_MMI_XXXX”, where XXXX is the last four digits of the VIN. Via Telephone > Options > Wi-Fi® options > Wi-Fi® Mode “Hotspot” > Hotspot settings > Access point (SSID) Perform with engine running to conserve battery power Post-Road Test Inspection • Check engine oil level Fill oil to the max level when the vehicle is at operating temperature • Enable satellite map for navigation Enable satellite map in the Navigation > Gear icon > Map Settings and verify the white Google logo appears in the bottom right-hand corner of the Navigation map screen. On-Hoist Inspection • Inspect wheel bolts for proper torque Use torque wrench to verify • Install wheel bolt covers and center caps as supplied Wheel bolt covers and center caps can be found in the PDI kit • Set and store tire pressures for either sold vehicle OR stock inventory vehicle If a known “sold” unit, set to appropriate Normal Load Condition. See separate “2020 Normal Load Condition Tire Pressure Table” posted on ServiceNet. If going to stock, set to maximum recommended tire pressures listed on the B-pillar door jamb, and store tire pressure values in Car/System menu Driving Performance • Verify engine performance and acceleration Listen for abnormal noise/vibrations • Test drive vehicle applying brakes several times Apply brakes at least 4 times at 20 mph (35 km/h) to clean brake rotors. Check for abnormal noise/vibration/pulsation Effective 1-24-2020-US Version 1.5 Model Year 2020 | Audi Pre-Delivery Reference Document | 29 TT Coupe & Roadster/TTS/TT RS Technician Reference Document Vehicle Preparation Trunk Inspection • Set adaption channel to enable CD Ripping using Guided Functions (if equipped with NAV) • Install wheel bolt cover removal tool from PDI kit into trunk tool kit Set adaptation channel (via Special functions > Service work > 5F-Activating/deactivating storage of music). Also referred to as CD Ripping. Perform 3 button reset of the MMI to complete the activation. Refer to the owner’s manual for model-specific button sequence • Perform any open campaigns Follow instructions listed in campaign documentation • Perform diagnostic work Connect vehicle diagnostic tester • Select “Diagnosis” mode and start diagnosis • Perform vehicle identification • Untick “Working with Guided Fault Finding” • Switch to “Special functions” tab and select following program: Delivery Inspection total Install wheel bolt cover removal tool from PDI kit and wheel lock key (if applicable) into trunk tool kit • Set spare tire pressure (NA for TT RS) See separate “Audi Normal Load Condition Tire Pressure Table” posted on ServiceNet under Pre-Delivery Inspection • Check battery clamps for proper torque Refer to Elsa Pro for specification Interior • Check operation of window, lock, and seat controls Check operation of all switches: Locks, windows, seat adjustment, heated seats (if equipped) and child safety features • Inspect mirrors for proper operation Inspect folding, adjustments, right side tilt in reverse, heating • Start program by selecting “Carry out check” • Check rear view mirror operation • Continue to follow instructions on screen and complete the process • Verify proper operation of climate control • Switch to the “Control units” tab, press the “Guided Fault Finding” button and launch Guided Fault Finding as far as the test plan • The static event memory entries must be evaluated and, if necessary, processed using Guided Fault Finding • Exit diagnosis; diagnostic log for delivery inspection is sent automatically • Install front license plate carrier (if necessary) • Retain any removed trim required for carrier installation and give to the customer. If no front license plate carrier is necessary ensure the carrier remains in the trunk for the customer Exterior • Check all key buttons and features Check functionality of all keys. Verify vehicle starts and runs with all keys and the start/stop button. Verify all doors and trunk remotely lock/unlock with all keys, including all door handle sensors with Advanced Key (if equipped) Check self-dimming function/lighting (if equipped) Ensure proper heating and A/C cooling and open all panel vents for all zones • Inspect operation of all power outlets Inspect operation of front outlet, aux. outlet under armrest, and rear outlets Settings • Set Time source setting to “GPS” and set Auto daylight savings time to “on.” Change time zone appropriate to the dealer location • Verify and set language and measurement units This can be changed in the Settings menu by going to Menu > Vehicle > Vehicle settings • Verify Speech Dialog System is operating Press the “Talk” button and verify several commands • Set “Entertain. Fad.” in Parking aid to an audible level Via “Menu > Vehicle > Left Option > Driver Assistance > Parking Aid” • Set dealership location in navigation (if equipped) Lighting and Windshield • Test front washers. Correct aim if necessary Set dealership location for following back to dealership during road test Headlights must be on to test functionality of the headlight washers Effective 1-24-2020-US Version 1.5 Model Year 2020 | Audi Pre-Delivery Reference Document | 30 TT Coupe & Roadster/TTS/TT RS Technician Reference Document Settings (continued) • Turn off Manual Speed Warning (if equipped) This can be changed in the Driver Assistance settings by going to Menu > Vehicle > Driver Assistance > Speed Warning > Manual->Select Off Media / Radio / SAT • Verify HD Radio is turned “off” This can be found in the Radio/Settings Menu On-Hoist Inspection • Inspect wheel bolts for proper torque Use torque wrench to verify • Install wheel bolt covers and center caps as supplied Wheel bolt covers and center caps can be found in the PDI kit • Set and store tire pressures for either sold vehicle OR stock inventory vehicle If a known “sold” unit, set to appropriate Normal Load Condition. See separate “Audi Normal Load Condition Tire Pressure Table” posted on ServiceNet. If going to stock, set to maximum recommended tire pressures listed on the B-pillar door jamb, and store tire pressure values in Car/System menu Driving Performance • Verify engine performance and acceleration Listen for abnormal noise/vibrations • Test drive vehicle applying brakes several times Apply brakes at least 4 times at 20 mph (35 km/h) to clean brake rotors. Check for abnormal noise/vibration/pulsation Driver Assistance • Verify operation of Audi parking system plus (if equipped) Verify operation of Audi parking system sensors with rear view camera (if equipped) Roadster Functionality (if equipped) • Test operation of power folding top Perform with engine running to conserve battery power Post-Road Test Inspection • Check engine oil level Fill oil to the max level when the vehicle is at operating temperature Effective 1-24-2020-US Version 1.5 Model Year 2020 | Audi Pre-Delivery Reference Document | 31