QT_ext range
Service Bulletin Details
Public Details for: QT_ext range
Information on the installation of remote start and extended range.
Models from 2020
2020 VOLKSWAGEN ARTEON |
2020 VOLKSWAGEN JETTA |
Models from 2019
2019 VOLKSWAGEN JETTA |
2019 VOLKSWAGEN TIGUAN |
Models from 2018
2018 VOLKSWAGEN ATLAS |
Quick tip Version 1.4 February 11th, 2020 Title: Remote start with extended range. (Only applies to 2019 Tiguan LWB, Jetta, GLI built after CW36/18, Atlas built after CW42/2018, 2020 Arteon) Remote start kit part number: 3CN065760 Plus Extended range kit part number: 000065760 Important notes: Only one (1) extended range fob can be programmed to the system at a time. If additional remote start keys are desired, factory standard range remote start key part number 3G0937048 and emergency key part number 3G0959752T DTB must be used. These keys must be ordered with the correct VIN. Always check ETKA for the latest part numbers. Page 1 of 12 “Always install the product according to the manufacturer's instructions. Modifications to the vehicle or accessory, or improper installation of the accessory can result in damage or failure.“ © 2020 Volkswagen Group of America, Inc. ver1.2 All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher. Step 1: • • • Step 2: Bend the door seal molding outward in the instrument panel cover area. Pry out the instrument panel side cover -1- with the -3409- near the catches. Pull the cover toward the rear and remove it. • Unclip the A-pillar gap cover -1- from the Apillar upper trim panel and A-pillar lower trim panel -arrows-. Loosen the A-pillar gap cover -1- from the door seal molding and remove it upward. Step 4: Step 3: • • • Remove the A-pillar upper trim panel Note: Inspect and replace the fasteners if necessary, part numbers 5NA867276B (x2) and 5G0867276A (x1). • Remove fuse panel cover. Page 2 of 12 “Always install the product according to the manufacturer's instructions. Modifications to the vehicle or accessory, or improper installation of the accessory can result in damage or failure.“ © 2020 Volkswagen Group of America, Inc. All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher. Step 5: Step 6: Locate the Relay labeled -548- and remove it. Install the new Relay labeled -526(comes in the Box). • • • • Locate fuse 49 Remove and discard. New design harness Original design harness Step 7a: • • • Step 7b: Insert red wire into the fuse holder. Insert black/red wire into fuse holder. Insert the 2-amp fuse into the fuse holder. • No harness preparation is required. Page 3 of 12 “Always install the product according to the manufacturer's instructions. Modifications to the vehicle or accessory, or improper installation of the accessory can result in damage or failure.“ © 2020 Volkswagen Group of America, Inc. All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher. Step 8a: • Step 8b: Mount the fuse holder to the bracket on the side of the relay panel. • Insert fuse holder into location SC20, SC7 or SC8 can be used if there is a fuse larger than 10 amp already in location SC20. Step 9a: • Insert the power wire in any open location shown above. Page 4 of 12 “Always install the product according to the manufacturer's instructions. Modifications to the vehicle or accessory, or improper installation of the accessory can result in damage or failure.“ © 2020 Volkswagen Group of America, Inc. All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher. Original and new design harness Step 10: • Step 11: • Use a cable tie and secure the module at the base of A-pillar. Route ground wire behind lower Apillar trim and connect to the chassis ground location under the carpet near the base of A-pillar. Page 5 of 12 “Always install the product according to the manufacturer's instructions. Modifications to the vehicle or accessory, or improper installation of the accessory can result in damage or failure.“ © 2020 Volkswagen Group of America, Inc. All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher. Step 12: • • On white BCM connector, insert line wire from kit into location 54. Note: If there is already a wire in this location use the provided splice connector. Step 13: • • • Step 14: • Route the antenna cable (supplied in the kit) -2- vertically on the left hand side of the mirror mount up to the headliner. Tuck the cable behind the headliner and down the “A” pillar and connect it to the module. Use the small wire ties -arrows- to secure the cable to the factory harness located within the “A” pillar. Reinstall all trim panels and the BCM connector that was previously removed. Page 6 of 12 “Always install the product according to the manufacturer's instructions. Modifications to the vehicle or accessory, or improper installation of the accessory can result in damage or failure.“ © 2020 Volkswagen Group of America, Inc. All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher. Step 15: Connect battery charger/maintainer. Connect scan tool. Scan the vehicle using GFF. Select Special Functions / Adapting software. Select Option 2 and enter SVM code 4196 (Jetta only), Code 3FBD V6 engine (Atlas) to update ECM. If vehicle is equipped with 2.0T engine skip this step. Select Special Functions / 0009-Remote start Select Adapting Software and Option 3 (conversion retrofit with license protection). Enter the SWAP keys located in pamphlet provided in remote start kit. Select Special Functions / Adapting software. Select Adapting Software and Option 2. Enter SVM code 425D to update BCM. • • • • • • • • • • Step 16: • Select “OBD.” Page 7 of 12 “Always install the product according to the manufacturer's instructions. Modifications to the vehicle or accessory, or improper installation of the accessory can result in damage or failure.“ © 2020 Volkswagen Group of America, Inc. All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher. Step 17: • Select “0009 – Central Electrics” basic settings, then select the “green arrow.” Step 18: • Select “adapting RF transmitter via barcode” then select the “arrow.” Page 8 of 12 “Always install the product according to the manufacturer's instructions. Modifications to the vehicle or accessory, or improper installation of the accessory can result in damage or failure.“ © 2020 Volkswagen Group of America, Inc. All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher. Step 19: • Select the “next arrow.” Step 20: • Enter the RF ID (HEX) and Private key (HEX) either manually with the keyboard or scan the QR code with a scanner. Page 9 of 12 “Always install the product according to the manufacturer's instructions. Modifications to the vehicle or accessory, or improper installation of the accessory can result in damage or failure.“ © 2020 Volkswagen Group of America, Inc. All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher. Step 21: • Select the “next arrow.” Step 22: • Select “Start.” Page 10 of 12 “Always install the product according to the manufacturer's instructions. Modifications to the vehicle or accessory, or improper installation of the accessory can result in damage or failure.“ © 2020 Volkswagen Group of America, Inc. All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher. Step 23: • After selecting “Start,” the result field should change to “[VO] Correct-Results” for a couple seconds. The process is completed. Step 24: • To test the operation, close all doors and lock the vehicle, Press the “Info” button once, then press the “Start” button twice on the new transmitter. Step 25: • Place the sticker with the RF ID (HEX) and Private key (HEX) on the extended range owner’s manual document. Place the document in the glove box with the owner’s manual. Page 11 of 12 “Always install the product according to the manufacturer's instructions. Modifications to the vehicle or accessory, or improper installation of the accessory can result in damage or failure.“ © 2020 Volkswagen Group of America, Inc. All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher. Conditions that will prevent system operation • • • • • • • • Programming failed. Check ETKA or ELSA Pro for new PR code #U2. Low fuel light illuminated. DTC’s in engine, transmission, vehicle electrics, ABS/ESP. Key fob/dongle not programmed. Vehicle out of range. Incorrect button sequence pressed on key fob/dongle. Remote start operation has ran 2 cycles without being started with vehicle key. Vehicle battery voltage too low. Page 12 of 12 “Always install the product according to the manufacturer's instructions. Modifications to the vehicle or accessory, or improper installation of the accessory can result in damage or failure.“ © 2020 Volkswagen Group of America, Inc. All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher.