ITB18-026c
Service Bulletin Details
Public Details for: ITB18-026c
Cvt fluid level quick check gauge this bulletin has been amended. See amendment history on the last page. Discard all previous versions of this bulletin.
- 2020 - 2019 - 2018 - 2017 - 2016 - 2015 - 2014 - 2013 -
Models from 2020
2020 INFINITI QX60 |
Models from 2019
2019 INFINITI QX60 |
Models from 2018
2018 INFINITI QX60 |
Models from 2017
2017 INFINITI QX60 |
Models from 2016
2016 INFINITI QX60 |
Models from 2015
2015 INFINITI QX60 |
Models from 2014
2014 INFINITI QX60 |
Models from 2013
2013 INFINITI JX35 |
Classification: Reference: Date: AT18-006c ITB18-026c March 13, 2020 CVT FLUID LEVEL QUICK CHECK GAUGE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin. APPLIED VEHICLES: 2013 JX35 (L50) 2014-2020 QX60 (L50) – Non-Hybrid APPLIED VIN and DATE: 2013 JX35 built AFTER 5N1AL0M(* *)DC 343902 and March 26, 2013 2014-2020 QX60 All SERVICE INFORMATION Special tools CVT Oil Level Quick Check Gauge (J-51155) and CVT Charge Pipe Cap Release (J-52611) are now available (see page 2). Each dealer has been shipped one each of these tools. Additional tools can be obtained from Tech•Mate at 1-800-662-2001. Refer to the SERVICE PROCEDURE starting on page 3 to determine how to perform a CVT fluid quick level check. Infiniti Bulletins are intended for use by qualified technicians, not 'do-it-yourselfers'. Qualified technicians are properly trained individuals who have the equipment, tools, safety instruction, and know-how to do a job properly and safely. NOTE: If you believe that a described condition may apply to a particular vehicle, DO NOT assume that it does. See your Infiniti retailer to determine if this applies to your vehicle. 1/6 SPECIAL TOOLS CVT Oil Level Quick Check Gauge (J-51155) TP180561 Figure 1 CVT Charge Pipe Cap Release (J-52611) Figure 2 2/6 ITB18-026c SERVICE PROCEDURE Inspect CVT Fluid Level NOTE: Steps 1 through 6 will ensure that CVT fluid is properly distributed throughout the CVT. A video on how to use tool J-52611 is available on nissantechmate.com: On the home page, type “J-52611” in the search window, select “Enter” on your keyboard, and then select Charge Pipe Cap Release Tool. 1. Park the vehicle on level ground (engine running, parking brake set). 2. Using CONSULT III plus (C-III plus), ensure that the CVT fluid operating temperature is within the range of 170°F-180°F (77°C-82°C). 3. Shift the transmission into REVERSE for 5 seconds. 4. Shift the transmission into DRIVE for 5 seconds. 5. Shift the transmission into REVERSE for 5 seconds. 6. Shift the transmission into PARK. 7. Install special tool CVT Charge Pipe Cap Release (J-52611) where shown in Figure 3. See page 2, SPECIAL TOOLS. NOTE: The tool shown in Figure 3 & Figure 4 is the same as the one shown in Figure 2, but looks slightly different. Squeeze 8. Squeeze the tool toward the cap, and then slightly lift the cap (see Figure 3). NOTE: The cap’s locking tab is unlocked while squeezing. Notice the gap between the cap and charging pipe in Figure 4. Cap J-52611 Figure 3 3/6 ITB18-026c 9. Remove tool J-52611 from the cap. Gap Charging pipe Figure 4 10. Pull to remove the cap from the charging pipe. Tool CVT Oil Level Quick Check Gauge (J-51155) can now be used to determine the CVT fluid level. Figure 5 4/6 ITB18-026c The handle on tool J-51155 has two positions – Red and Blue. Refer to Table A on the next page for the correct position for a given vehicle. Red Blue 11. Figure 6 OK NG With the vehicle in PARK and the engine running, insert tool J-51155 into the pipe. TP180558 TP180557 Make sure to use the correct handle position (refer to Table A). Blue Red TP180559 TP180558 Figure 7 5/6 ITB18-026c Table A MODEL LEVEL (MM) HANDLE POSITION 2013 JX35 (See APPLIED VIN and DATE on page 1) 14-22 Red 2014-2020 QX60 (non-Hybrid) 60 mm 12. Inspect the oil level quick check gauge to determine the CVT oil level in millimeters and compare the reading to the specifications in Table A, above. 10 mm TP180560 Figure 8 ADJUST CVT FLUID LEVEL 13. Adjust the fluid level from the bottom of the CVT according to the procedure in the Electronic Service Manual (ESM). AMENDMENT HISTORY Published DATE REFERENCE DESCRIPTION August 15, 2018 ITB18-026 Original bulletin published November 5, 2018 ITB18-026a March 20, 2019 ITB18-026b March 13, 2020 ITB18-026c Steps 1 and 2 revised Table A amended, the picture of tool J-51155 moved to page 2, and tool J-52611 added APPLIED VEHICLES and Table A amended 6/6 ITB18-026c