T-SB-0040-16 Rev

T-SB-0040-16
Rev2
May 13, 2016
Load Configuration Data
Service
Category
Engine/Hybrid System
Section
Engine Control
Market USA
Applicability
YEAR(S)
MODEL(S)
2016 - 2020
Yaris SD MEX-Prod
2017 - 2018
iA
ADDITIONAL INFORMATION
REVISION NOTICE
June 21, 2020 Rev2:
 Applicability has been updated to include 2018 – 2020 Yaris SD and 2018 iA
model year vehicles.
 The entire bulletin has been updated.
September 7, 2016 Rev1:
 Applicability has been updated to include 2017 model year iA vehicles.
Any previous printed versions of this bulletin should be discarded.
Introduction
This bulletin details the procedure for loading configuration data (also known as As-built data) in
the ECUs of 2016 – 2020 model year Yaris Sedan Mexico-produced and 2017 – 2018 model year
iA vehicles. It is not recommended to swap ECUs between vehicles. The configuration data must
be loaded into the ECU when replacing one of the ECUs listed below:

PCM (Engine ECU).

TCM (Transmission ECU).
IC (Instrument Cluster or Combination Meter ECU).



SSU (Smart Key ECU).
RCM (Restraint Control Module/Airbag ECU).
© 2020 Toyota Motor Sales, USA
Page 1 of 13
T-SB-0040-16
Rev2
May 13, 2016
Page 2 of 13
Load Configuration Data
Introduction (continued)
There are two different ways to load configuration data into a new ECU:
1. The data must be saved from the old ECU to load into the new ECU. This method is used
when an ECU requires replacement, however you can still communicate with the ECU and
read the existing As-built data. This is the preferred method and should be attempted first, as it
will ensure that the current ECU calibration is reinstalled on the ECU after repair
(for TCM and PCM).
Follow steps 1 – 8 of the Repair Procedure in this bulletin for instructions on how to save the
data. Once at step 8, start over at step 1 after replacing the ECU to load the data.
2. The data can be downloaded from the server. Downloading the calibration from the server will
load the original calibration as it was built from the factory (for TCM and PCM). This method is
used when you can no longer communicate with the ECU, or the Repair Manual has instructed
you to re-load As-Built Data without replacing the ECU.
Follow the Repair Procedure to load data from the server into the ECU.
Warranty Information
OP CODE
DESCRIPTION
TIME
OFP
T1
T2
N/A
Not Applicable to Warranty
–
–
–
–
Required Tools & Equipment
REQUIRED EQUIPMENT
SUPPLIER
Techstream ADVi*
QTY
TSADVUNIT
Techstream 2.0
Techstream Lite
PART NUMBER
TS2UNIT
ADE
Techstream Lite (Green Cable)
TSLITEPDLR01
TSLP2DLR01
*Essential SST.
NOTE
 Only ONE of the Techstream units listed above is required.
 Software version 15.00.028 or later is required.
 Additional Techstream units may be ordered by calling Approved Dealer Equipment (ADE)
at 1-800-368-6787.
© 2020 Toyota Motor Sales, USA
1
T-SB-0040-16
Rev2
May 13, 2016
Load Configuration Data
Repair Procedure
1. Connect Techstream to the vehicle.
Figure 1.
2. Select the correct vehicle Division, Model, and Model Year.
Figure 2.
© 2020 Toyota Motor Sales, USA
Page 3 of 13
T-SB-0040-16
Rev2
May 13, 2016
Load Configuration Data
Repair Procedure (continued)
3. Select the ECU of the system you are loading configuration data.
Figure 3.
4. Select Utility.
Figure 4.
© 2020 Toyota Motor Sales, USA
Page 4 of 13
T-SB-0040-16
Rev2
May 13, 2016
Load Configuration Data
Repair Procedure (continued)
5. Select Configuration.
Figure 5.
6. Follow the prompts on the Utility pop-up screens.
Figure 6.
© 2020 Toyota Motor Sales, USA
Page 5 of 13
T-SB-0040-16
Rev2
May 13, 2016
Page 6 of 13
Load Configuration Data
Repair Procedure (continued)
7. If you are saving the current configuration data to load into a NEW ECU, select Before
ECU Replacement and select Next. This will save the data currently on the ECU.
If you have installed the NEW blank ECU and have either saved the old data OR want to
download the data from the server, OR the Repair Manual has instructed you to load
configuration data on an old ECU, select After ECU Replacement and select Next.
Figure 7.
© 2020 Toyota Motor Sales, USA
T-SB-0040-16
Rev2
May 13, 2016
Page 7 of 13
Load Configuration Data
Repair Procedure (continued)
8. Enter the 17-digit VIN of the vehicle being worked on.
Figure 8.
NOTE
If you are transferring data from an old ECU to a new ECU, start over at step 1 of the Repair
Procedure AFTER completing step 8 and replacing the ECU to load the data.
© 2020 Toyota Motor Sales, USA
T-SB-0040-16
Rev2
May 13, 2016
Page 8 of 13
Load Configuration Data
Repair Procedure (continued)
9. If you are loading configuration data for the PCM or TCM, a download window will open
prompting the download of the calibration for that vehicle. Select Open to open the
Calibration Update Wizard (CUW).
If you are loading data for ANY other system, go to step 12.
Figure 9.
© 2020 Toyota Motor Sales, USA
T-SB-0040-16
Rev2
May 13, 2016
Page 9 of 13
Load Configuration Data
Repair Procedure (continued)
10. Follow the instructions for CUW. See Service Bulletin T-SB-0134-16 Techstream ECU
Flash Reprogramming Procedure for more details.
Figure 10.
© 2020 Toyota Motor Sales, USA
T-SB-0040-16
Rev2
May 13, 2016
Page 10 of 13
Load Configuration Data
Repair Procedure (continued)
11. Once the calibration has been loaded into the vehicle, select Finish to close CUW.
NOTE
The procedure is NOT complete yet. Continue through the rest of the bulletin.
Figure 11.
© 2020 Toyota Motor Sales, USA
T-SB-0040-16
Rev2
May 13, 2016
Page 11 of 13
Load Configuration Data
Repair Procedure (continued)
12. Continue to follow the prompts in the Utility screens to load the configuration data.
Figure 12.
Figure 13.
© 2020 Toyota Motor Sales, USA
T-SB-0040-16
Rev2
May 13, 2016
Page 12 of 13
Load Configuration Data
Repair Procedure (continued)
13. Turn the engine/power switch OFF and ON (engine OFF/ready OFF), then press Next
to proceed.
Figure 14.
© 2020 Toyota Motor Sales, USA
T-SB-0040-16
Rev2
May 13, 2016
Page 13 of 13
Load Configuration Data
Repair Procedure (continued)
14. Configuration is complete, select Exit.
NOTE
If the PCM or SSU ECU was replaced, you MUST complete the handshake to register them
together. Perform procedure B of T-SB-0013-16.
Figure 15.
15. Perform a Health Check and check for ANY updated calibrations. If there are updates, check to
see if the vehicle model and model year are applicable and load as necessary.
© 2020 Toyota Motor Sales, USA