FSB 519-001
Service Bulletin Details
Public Details for: FSB 519-001
Dust cover, drive axle, replacement
- 9999 -
Models from 9999
9999 VOLVO VAH |
9999 VOLVO VHD |
9999 VOLVO VN |
9999 VOLVO VT |
Field Service Bulletin Trucks Volvo Trucks North America Greensboro, NC USA Date 7.2020 Group No. Release 519 001 01 Page 1(10) Dust Cover, Drive Axle, Replace VN, VHD, VAH, VT FSB 519-001, Dust Cover, Drive Axle, Replacement (July 2020) Certain Volvo Trucks VAH, VHD, VN and VT models produced between October 02, 2002, and June 08, 2020, and equipped with drive axle, dust covers, may experience premature failures of the drive axle dust cover. Solution If this condition exists, follow the procedures outlined in this FSB. Order parts listed in required parts section and repair vehicles as per instructions outlined in this FSB. Service personnel: Please circulate, read and initial Service Manager PV729-89469308 Warranty Administrator Workshop Foreman Service Technicians USA152331243 Volvo Trucks North America Field Service Bulletin Date 7.2020 Group No. Release 519 001 01 Required Parts 1 Bendix Dust Cover. T5161856 SI No Part Description 1 Bracket 2 Dust cover 3 Fasteners New part number Quantity 1 Shield Kit 23778303 1 2 Page 2(10) Volvo Trucks North America Field Service Bulletin Date 7.2020 Group No. Release 519 001 01 Decommissioning the Truck for Repair 5 You must read and understand the precautions and guidelines in Service Information, group 71, "General Safety Practices, Body, Cab and HVAC" before performing this procedure. If you are not properly trained and certified in this procedure, ask your supervisor for training before you perform it. NOTE: Information is subject to change without notice. Illustrations are used for reference only and can differ slightly from the actual vehicle being serviced. However, key components addressed in this information are represented as accurately as possible. 1 Park the vehicle on a flat and level surface. 2 Apply the parking brake. 3 Place the transmission in neutral or park. 4 Install the wheel chocks. W7086748 Page 3(10) Volvo Trucks North America Field Service Bulletin Date 7.2020 Group No. Release 519 001 01 5 Disconnect the cable from the battery’s negative terminal. W3086747 Page 4(10) Volvo Trucks North America Field Service Bulletin Date 7.2020 Group No. Release 519 001 01 Procedure 1 Remove the screws. T5161853 Page 5(10) Volvo Trucks North America Field Service Bulletin Date 7.2020 Group No. Release 519 001 01 2 Remove the dust cover. T5161855 Page 6(10) Volvo Trucks North America Field Service Bulletin Date 7.2020 Group No. Release 519 001 01 3 Install the new bendix dust cover. T5161857 Page 7(10) Volvo Trucks North America Field Service Bulletin Date 7.2020 Group No. Release 519 001 01 4 Install the screws. Torque tighten the screws. 1 Screw (Bendix Dust Cover) 24±40 Nm (18 ft,lbs) 2 Screw (additional bracket) 24±40 Nm (18 ft,lbs) T5161858 Page 8(10) Volvo Trucks North America Field Service Bulletin Date 7.2020 Group No. Release 519 001 01 Commissioning the Truck for Operation 1 Connect the battery cable to the negative (ground) terminal. W3086758 Page 9(10) Volvo Trucks North America Field Service Bulletin Date 7.2020 Group No. Release 519 001 01 2 Remove the wheel chocks. W7086759 Reimbursement This repair may be eligible for reimbursement if a product failure was experienced within time and mileage limits of the applicable warranty coverage. Reimbursement is obtained via the normal claim handling process. UCHP Reimbursement Claim type (used only when uploading from the dealer Bus. Sys.) 01 Labour Code 5129–03–02–16 Standard time 0.3 hrs Volvo Trucks North America reserves the right to make any changes in design or to make additions to or upon its products without incurring any obligations to install the same on vehicles previously built. Page 10(10)