01-004-20

THULE® REGAL AWNING INSPECTION
TSB Number: TSB 01-004-20B
Product: Thule® Regal Awning
Date: June 19, 2020
Note: This bulletin supersedes TSB 01-004-20 dated April 17, 2020, which should be removed from your files.
Purpose
This document outlines the inspection (and correction) of Thule Regal Awnings to determine if there is too
much gap between the roll tube and end plates, which could cause the fabric to extend over the edge or the
roll tube could shift along the axle plane.
Safety
This document provides general instructions. Many variables can change the circumstances of any
procedure, i.e. the degree of difficulty involved in the service operation and the ability level of the individual
performing the operation. This document cannot begin to plot out procedures for every possibility, but will
provide the general instructions for effectively installing, removing or servicing the system. In the event the
skill level required is too advanced or the procedure too difficult, a certified technician should be consulted
before performing the necessary operation. Failure to correctly install, remove or service the system may
result in voiding the warranty, inflicting injury or even death.
The “WARNING” symbol above is a sign that a procedure has a safety risk involved and may cause
death, serious personal injury, severe product and/or property damage if not performed safely and
within the parameters set forth in this document.
The "CAUTION" symbol above is a sign that a procedure has a safety risk involved and may cause
personal injury, product and/or property damage if not performed safely and within the parameters
set forth in this document.
Resources Required
•
•
•
•
•
•
Thule Regal Tolerance Adjustment Kit
Note: Use parts as needed. Discard unused parts.
Cordless or electric drill or screwdriver
Appropriate drive bits
Small hammer or mallet
Micrometer
Metric T-handle wrenches (optional)
Flat head screwdriver or pry bar
Thule Regal Tolerance Adjustment Kit - 2020115013
Description
Qty
Instruction manual
1
Washers
6
Front end cap screw
1
Rear end cap screws
3
End plate screws
2
QA approved sticker (See figure 21)
1
Labor Time
Inspection: 0.3 hours (need two measurements)
Corrective Action: 0.3 hours(adding washers)
Rev: 06.19.20
Page 1
CCD-0003853
THULE® REGAL AWNING INSPECTION
TSB Number: TSB 01-004-20B
Product: Thule® Regal Awning
Date: June 19, 2020
Inspection
Check the following steps on the flow chart (Fig. 1 ) to determine if the awning needs to be modified.
Fig. 1
Rev: 06.19.20
Page 2
CCD-0003853
THULE® REGAL AWNING INSPECTION
TSB Number: TSB 01-004-20B
Product: Thule® Regal Awning
Date: June 19, 2020
Production Label Inspection
1.
2.
Open the awning at least three feet.
Check for the production label (Fig. 2A) near the left hand end cap, inside the lead rail profile.
Fig. 2
A
Note: If the production label is not present, go to the Screw Inspection section on page 4. If the
production label is present and dated (DD/MM/YY) prior to February 2020, skip to the Tolerance
Inspection on page 5. If the production label is present and dated (DD/MM/YY) February 2020 or
later, no further action is needed.
Rev: 06.19.20
Page 3
CCD-0003853
THULE® REGAL AWNING INSPECTION
TSB Number: TSB 01-004-20B
Product: Thule® Regal Awning
Date: June 19, 2020
Screw Inspection
1.
Physically move/rock the end caps to check fixation of the end plate with 20mm torx fasteners.
Note: Visual inspection of the two 20mm torx fasteners (Fig. 6) will require removal of the end caps.
2.
Open the awning at least three feet.
Use caution removing the fasteners securing the end caps, they can easily be stripped.
3.
4.
Remove the 15mm torx fastener securing the front end cap (Fig. 3) with appropriate bit.
Pop off the front end cap (Fig. 4A) with a flat head screwdriver or pry bar.
Fig. 4
Fig. 3
A
5.
6.
Remove the three 3mm hex fasteners (Fig. 5) securing the rear end cap with appropriate bit.
Verify the presence of the two 20mm torx fasteners (Fig. 6) on the awning end plate.
Fig. 6
Fig. 5
7. Repeat steps 2 through 6 for the other end cap. Retain all hardware for re-installation.
If the fasteners are present on the awning ends, go to the Tolerance Inspection section on page 5. If the
fasteners are not present, install the two 20mm torx fasteners provided.
Rev: 06.19.20
Page 4
CCD-0003853
THULE® REGAL AWNING INSPECTION
TSB Number: TSB 01-004-20B
Product: Thule® Regal Awning
Date: June 19, 2020
Tolerance Inspection
Note: If the end caps have already been removed for screw inspection, skip to step 6.
1.
Open the awning at least three feet.
Use caution removing the fastener securing the front end cap, it can easily be stripped.
2.
3.
Remove the 15mm torx fastener securing the front end cap (Fig. 7) with appropriate bit.
Pop off the front end cap (Fig. 8A) with a flat head screwdriver or pry bar.
Fig. 7
Fig. 8
A
4.
5.
6.
7.
Set front end cap (Fig. 8A) aside for re-installation.
Repeat steps 1 through 4 for the other end cap. Retain hardware for re-installation.
Using a micrometer measure the gap between the awning roll tube and end plates on both the right
and left sides (Fig. 10).
Add the two measurements and see Tolerance Inspection Table on page 6 for measurement specifics.
Fig. 9
Rev: 06.19.20
Fig. 10
Page 5
CCD-0003853
THULE® REGAL AWNING INSPECTION
TSB Number: TSB 01-004-20B
Product: Thule® Regal Awning
Date: June 19, 2020
Tolerance Inspection Table
Procedure
1. Measure the gap on the left and right sides (Fig. 11).
• Measure at the axle centerline height.
• The minimum is always 8mm (0.3150")
Fig. 11
2.
Add both values and compare with table below.
Gap sum (mm)
Gap sum (")
16mm - 17mm
0.6299" - 0.6693"
17.1mm - 18mm
0.6732" - 0.7087"
18.1mm - 19mm
0.7126" - 0.7480"
19.1mm - 20mm
0.7520" - 0.7874"
20.1mm - 21mm
0.7913" - 0.8268"
21.1mm - 22mm
0.8307" - 0.8661"
(*) DIN988 A2 (16mm x 22mm x 1mm)
3.
Rev: 06.19.20
Action
No action
Add 1 washer (*)
Add 2 washers (*)
Add 3 washers (*)
Add 4 washers (*)
Add 5 washers (*)
See Corrective Action section on page 7 if washers need to be added.
Page 6
CCD-0003853
THULE® REGAL AWNING INSPECTION
TSB Number: TSB 01-004-20B
Product: Thule® Regal Awning
Date: June 19, 2020
Corrective Action
Note: This action should be performed on the left side only.
1.
2.
3.
Open the awning completely.
Tie up the spring arms (Fig 12).
Release all the fabric tension. DO NOT proceed to step 6 until fabric tension is released.
Note: If the rear end cap has already been removed in a previous section, skip to step 6.
4.
5.
Remove the three 3mm hex fasteners securing the rear end cap (Fig. 13) using appropriate bit.
Remove rear end cap (Fig. 14).
Fig. 12
6.
7.
8.
Fig. 14
Remove the two 20mm Torx fasteners from the end plate (Fig. 15) using appropriate bit.
Remove the end plate (Fig. 16).
Add the necessary washers (Fig. 17) according to the table on page 6.
Fig. 15
Rev: 06.19.20
Fig. 13
Fig. 16
Page 7
Fig. 17
CCD-0003853
THULE® REGAL AWNING INSPECTION
TSB Number: TSB 01-004-20
Product: Thule® Regal Awning
Date: April 2, 2020
9. Tap the axle with small hammer or mallet to eliminate excess play (Fig. 18).
10. Align the end plate on the axle (Fig. 19) and secure with previously-removed 20mm Torx fasteners (Fig. 20).
Fig. 18
Fig. 19
Fig. 20
11. Individually dry fit the end cap(s), taking care not to pinch or cut the wires on the drive head side.
12. Re-install the three 3mm hex fasteners with appropriate bit (Fig. 13).
13. Re-install the 20mm Torx fastener using appropriate bit (Fig. 7).
Use caution re-installing the fasteners securing the rear end cap, they can easily be stripped.
Install Quality Label
1.
Install quality label (Fig. 21) on production label as shown below or at this location near the left hand
end cap inside the lead rail profile, if there is no production label present.
Fig. 21
As a supplier of components to the RV industry, safety, education and customer satisfaction are our primary concerns. Should you
have any questions, please do not hesitate to contact us at (574) 537-8900 or by email at [email protected]. Self-help tips,
technical documents, product videos and a training class schedule are available at lci1.com or by downloading the MyLCI app.
Rev: 06.19.20
Page 8
CCD-0003853