V6920022061220_2
Service Bulletin Details
Public Details for: V6920022061220_2
Updated programming of the airbag control module (0015) -j234- software.
Models from 2021
2021 VOLKSWAGEN ATLAS |
Models from 2020
2020 VOLKSWAGEN ATLAS CROSS SPORT |
Technical Service Bulletin 69-20-02 - Update Programming, DTC B101612 Stored Transaction No: 2061220/2 Release date: 11/11/2020 Condition Applicable Vehicles Model(s) Year Eng. Code Trans. Code VIN Range From VIN Range To Atlas 2021 All All CA_MC500001 CA_MC521445 Atlas CrossSport 2020 All All CA_LC200001 CA_LC225415 Revision Table Instance Number Published Date Version Number Reason For Update 2061220/2 11/11/20 69-20-02 Administrative. 2061220/1 1029/20 69-20-02 Original publication. One or more of the following fault codes may be stored in the Airbag Control Module (0015) -J234- Fault Memory: DTC B101612 Description Passenger airbag disabled light short to Vbat. Note: DO NOT diagnose or replace components due to DTC B101612 faults before performing the update function as explained in this bulletin. Page 1 of 5 © 2020 Volkswagen Group of America, Inc. All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher. Technical Service Bulletin 69-20-02 - Update Programming, DTC B101612 Stored Transaction No: 2061220/2 Release date: 11/11/2020 Technical Background Airbag icon illuminated in Instrument Cluster -KX2-. Updated programming of the Airbag Control Module (0015) -J234- software is based on most recent engineering experiences and makes this knowledge available for the monitoring strategies. Production Solution Improved software in production since August 13, 2020. Service Update-Programming Procedure: Critical Warning: : The Midtronics battery charger must be connected to the vehicle battery for the duration of the programming, to ensure the battery state of charge remains above 12.5 volts during the update process. If the battery drops below 12.5 volts, the programming could fail which may result in damage to the control module. Control modules damaged by inadequate voltage will not be covered under the warranty policy. The technician should verify the vehicle voltage prior to starting the update process, and should monitor the voltage for the duration of the update. The procedure may cancel itself if the hazard warning lights are not switched ON. The hazard warning lights prevent the system from switching to bus sleep mode during the update. ODIS-Service tester should be updated to the latest GFF technical version 2.40.15 or higher and SW version 6.2.0. or higher. Note: Prior to launching the ODIS Service diagnostic applications and starting control module update process, confirm tester screen saver and power settings in accordance with Diagnostic Device Hardware & Windows® - VHW-20-02 Change Power Options After Windows®10 Upgrade. Failure to do so may result in the tester entering power save mode during data transfer, and subsequent control module failure. When using a VAS 6150/X or 6160/X tester in conjunction with a VAS 6154 wireless transmitter head for a flash procedure, connect a USB cable between the transmitter head and the tester. Failure to do so may lead to errors during the flash procedure. VAS tools must only be used with their power adapters plugged in. Under no circumstances should they be used on battery power alone during the programming procedure. Tip: To Update-Programming using Software Version Management (SVM), review and follow instructions in Technical Bulletin Instance 2014603 “Software Version Management”. The SVM process must be completed in its entirety so the database receives the update confirmation response. A warranty claim may not be reimbursed if there is no confirmation response to support the claim or action is carried out that is not explicitly stated in the Technical Bulletin. Page 2 of 5 © 2020 Volkswagen Group of America, Inc. All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher. Technical Service Bulletin 69-20-02 - Update Programming, DTC B101612 Stored Transaction No: 2061220/2 Release date: 11/11/2020 Update the Airbag Control Module (0015) -J234- using the SVM Unit code as listed in the table below: Go to diagnostic address 0015 – airbag: Perform GFF replacement control module test plan. Model Engine Old Software Part No. Old Software Version New Software Part No. New Software Version (or higher) SVM Unit Code Atlas All 3Q0959655DB 720 3Q0959655DB 721 4488 Atlas CrossSport All 3Q0959655DB 720 3Q0959655DB 721 4488 Note: If you have a "FAZIT" error perform component protection test pan for address word 0015. Tip: The procedure can be found in GFF under Functions/ Component Selection, Software Version Management, Adapting Software (0015). Page 3 of 5 © 2020 Volkswagen Group of America, Inc. All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher. Technical Service Bulletin 69-20-02 - Update Programming, DTC B101612 Stored Transaction No: 2061220/2 Release date: 11/11/2020 Warranty To determine if this procedure is covered under Warranty, always refer to the Warranty Policies and Procedures Manual 1) Model(s) Year(s) Eng. Code(s) Trans. Code(s) VIN Range From VIN Range To Atlas 2021 All All CA_MC500001 CA_MC521445 Atlas CrossSport 2020 All All CA_LC200001 CA_LC225415 SAGA Coding Claim Type: Use applicable Claim Type 1) Service Number: Damage Code 6982 HST Damage Location (Depends on Service No.) -- -- 0039 Atlas, Atlas CrossSport Parts Manufacturer WWO 2) Labor Operation 3) : Charge Battery 27068950 = See Elsa for latest time units. Labor Operation 3) : Update Programming Airbag Control Module 69531999 = 65TU Causal Part: Select Labor Operation 69531999 Diagnostic Time 4) GFF Time expenditure 01500000 = 00 TU NO Road Test 01210004 = 10 TU YES Technical Diagnosis 01320000 = 00 TU max. NO Claim Comment: Input “As per Technical Bulletin 2061220” in comment section of Warranty Claim. 1) Vehicle may be outside any Warranty in which case this Technical Bulletin is informational only. 2) Code per warranty vendor code policy. Page 4 of 5 © 2020 Volkswagen Group of America, Inc. All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher. Technical Service Bulletin 69-20-02 - Update Programming, DTC B101612 Stored 3) Labor Time Units (TUs) are subject to change with ELSA updates. 4) Documentation required per Warranty Policies and Procedures Manual. Transaction No: 2061220/2 Release date: 11/11/2020 Required Parts and Tools No Special Parts required. Tool Description Tool No: Midtronics Battery Tester/Charger GRX3000VAS or MTRMSP0702 battery maintainer/charger VAS Diagnostic Tool VAS 6150/X & VAS 6160/X and ODIS Service with current online updates Additional Information All part and service references provided in this Technical Bulletin are subject to change and/or removal. Always check with your Parts Dept. and Repair Manuals for the latest information. Page 5 of 5 © 2020 Volkswagen Group of America, Inc. All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher.