LTB00865NAS3

11/24/2020
https://www.odyssey.jlrint.com/odyssey/WorkflowHtmlComposition.do?wid=1606135885824
LT B 0 0 8 6 5 N A S 3
TECHNICAL BULLETIN
24 NOV 2020
© Jaguar Land Rover North America, LLC
NOTE: The information in Technical Bulletins is intended for use by trained, professional
Technicians with the knowledge, tools, and equipment required to do the job properly
and safely. It informs these Technicians of conditions that may occur on some vehicles, or
provides information that could assist in proper vehicle service. The procedures should
not be performed by 'do-it-yourselfers'. If you are not a Retailer, do not assume that a
condition described affects your vehicle. Contact an authorized Land Rover service facility
to determine whether this bulletin applies to a specific vehicle.
I N F O R M AT I O N
This reissue replaces all previous versions. Please destroy all previous versions.
This bulletin supersedes TSB LTB00865NAS2/2019 dated 10 APR 2019, which should
either be destroyed or clearly marked to show it is no longer valid (e.g. with a line across
the page). Only refer to the electronic version of this Technical Bulletin in TOPIx.
SECTION:
501-08
S U B J E C T/ C O N C E R N :
Roof Molding Loose / Adrift
AFFECTED VEHICLE RANGE:
MODEL:
Discovery Sport (LC)
MODEL YEAR:
2015-2020
VIN:
500429-872128
https://www.odyssey.jlrint.com/odyssey/WorkflowHtmlComposition.do?wid=1606135885824
ASSEMBLY PLANT:
Halewood
1/7
11/24/2020
https://www.odyssey.jlrint.com/odyssey/WorkflowHtmlComposition.do?wid=1606135885824
MARKETS:
NORTH AMERICA
CONDITION SUMMARY:
SITUATION:
The left and/or right roof molding may be loose / adrift.
CAUSE:
This may be caused by a failed bonding process between the roof molding stud and the
roof molding.
ACTION:
Follow the instructions below.
PA RTS :
NOTE:
an allowance of $13.00 has been allocated for locally sourcing the adhesive
applicator nozzles; claim using ZZZ001.
PART NUMBER
DESCRIPTION
QUANTITY
LR061141
Clip(s) - Right - Front
1
LR061142
Clip(s) - Left - Front
1
LR061147
Retainer(s) [as required]
1
LR061143
Stud(s) - Roof molding [as required]
12
LR061139
Clip(s) - Roof molding [as required]
10
LR061146
Retainer(s) [as required]
1
LR061144
Clip(s) - Right - Rear [as required]
1
LR061145
Clip(s) - Left - Rear [as required]
1
LR084482
Adhesive pack
1
ZZZ001
Adhesive applicator nozzle
1
https://www.odyssey.jlrint.com/odyssey/WorkflowHtmlComposition.do?wid=1606135885824
2/7
11/24/2020
https://www.odyssey.jlrint.com/odyssey/WorkflowHtmlComposition.do?wid=1606135885824
WARRANT Y:
NOTE:
an allowance of $13.00 has been allocated for locally sourcing the adhesive
applicator nozzles; claim using ZZZ001.
NOTES:
Repair procedures are under constant review, and therefore times are subject to
change; those quoted here must be taken as guidance only. Use TOPIx to obtain
the latest repair time.
The JLR claims submission system requires the use of causal part numbers. Labor
only claims must show the causal part number with a quantity of zero.
DESCRIPTION
SRO
TIME
(HOURS)
CONDITION
CODE
CAUSAL
PART
Roof - Molding - Stud - Left Renew
76.43.68.89
0.4
DS
LR061143
Roof - Molding - Stud - Right Renew
76.43.68.90
0.4
DS
LR061143
Roof - Molding - Stud - Pair Renew
76.43.68.91
0.7
DS
LR061143
NOTE:
Normal Warranty procedures apply.
C O M P O N E N T L O C AT I O N :
https://www.odyssey.jlrint.com/odyssey/WorkflowHtmlComposition.do?wid=1606135885824
3/7
11/24/2020
https://www.odyssey.jlrint.com/odyssey/WorkflowHtmlComposition.do?wid=1606135885824
1.
CAUTION:
Only use the adhesive from the parts list to complete this procedure.

Component location.
WORKSHOP PROCEDURE:
1.
NOTE:
Only remove the roof molding that is loose or adrift.
Remove and inspect the roof molding for any damage present, (see TOPIx
Workshop Manual section 501-08: Exterior Trim and Ornamentation - Removal Roof Molding).
If the roof molding is damaged, discard the roof molding and continue
to step 2.
If the roof molding is not damaged, retain the roof molding and
continue to step 2.
https://www.odyssey.jlrint.com/odyssey/WorkflowHtmlComposition.do?wid=1606135885824
4/7
11/24/2020
https://www.odyssey.jlrint.com/odyssey/WorkflowHtmlComposition.do?wid=1606135885824
2.
CAUTION:
Care must be taken to avoid damaging the surrounding paintwork.

Use a suitable tool to remove the 12 roof molding studs.
3.

Use a suitable degreaser to clean the area shown.
https://www.odyssey.jlrint.com/odyssey/WorkflowHtmlComposition.do?wid=1606135885824
5/7
11/24/2020
https://www.odyssey.jlrint.com/odyssey/WorkflowHtmlComposition.do?wid=1606135885824
4.

Starting at the windshield (1) and moving towards the rear of the roof panel (2),
use a suitable marker to mark the roof channel in the positions indicated.
5.
CAUTION:
Do not apply excessive amounts of the bonding adhesive.
NOTE:
Make sure the bonding adhesive is applied to the center of the roof
channel at each marking.

Apply the bonding adhesive to the areas previously marked in Step 4.
https://www.odyssey.jlrint.com/odyssey/WorkflowHtmlComposition.do?wid=1606135885824
6/7
11/24/2020
https://www.odyssey.jlrint.com/odyssey/WorkflowHtmlComposition.do?wid=1606135885824
6.
CAUTION:
A minimum of 24 hours is required for the bonding adhesive to cure
before installing the roof molding.
NOTE:
Make sure the new roof studs are applied in the center of the roof
channel.

Install the new roof molding studs in the positions previously applied with
bonding glue.
7.
NOTES:
If the roof molding(s) is damaged, renew the molding; do not install a
damaged molding(s).
Renew the roof molding, if required.
Install the roof molding (see TOPIx Workshop Manual section 501-08: Exterior
Trim and Ornamentation - Removal and Installation - Roof Molding).
8.
Complete steps 1 - 7 for the opposite side of the vehicle, if required.
https://www.odyssey.jlrint.com/odyssey/WorkflowHtmlComposition.do?wid=1606135885824
7/7