T-SB-0120-20
Service Bulletin Details
Public Details for: T-SB-0120-20
Tsb: some 2021 model year venza hybrid vehicles may require the download and installation of vehicle specific software or configuration software when the electronic control unit (ecu) is replaced. Techstream software has been modified to in
- 2021 -
Models from 2021
2021 TOYOTA VENZA HYBRID |
T-SB-0120-20 December 11, 2020 Replacement ECU Software Configure Process Service Category Steering Section Power Assist Systems Market USA Applicability YEAR(S) MODEL(S) 2021 Venza HV ADDITIONAL INFORMATION Introduction Some 2021 model year Venza Hybrid vehicles may require the download and installation of vehicle specific software or configuration software when the Electronic Control Unit (ECU) is replaced. Techstream software has been modified to indicate when configuration software is required. A new Configure column has been added to the Techstream Health Check Results screen to show when configuration software is available for a specific ECU. Follow the Operation Procedure in this bulletin to complete the ECU Software Configure Process. Refer to the applicability chart below for a list of Models and ECUs that will require configuration software when the specified ECU is replaced: YEAR(S) MODEL(S) ECU(S) REQUIRING CONFIGURATION SOFTWARE 2021 Venza HV EMPS ECU NOTE ECU is a Toyota term used to describe integrated computerized devices responsible for managing the operation of a system or subsystem. In this bulletin, ECU is used as a generic label for the following SAE J1930 standard references: Powertrain Control Module (PCM). Engine Control Module (ECM). Transmission Control Module (TCM). Any other Toyota specific control unit. © 2020 Toyota Motor Sales, USA Page 1 of 9 T-SB-0120-20 December 11, 2020 Page 2 of 9 Replacement ECU Software Configure Process Required Tools & Equipment SPECIAL SERVICE TOOLS (SST) PART NUMBER QTY Battery Diagnostic Tool* DCA-8000P T 1 *Essential SST. NOTE Additional SSTs may be ordered by calling 1-800-933-8335. REQUIRED EQUIPMENT SUPPLIER Techstream ADVI* PART NUMBER QTY TSADVUNIT Techstream 2.0 TS2UNIT ADE 1 Techstream Lite TSLITEPDLR01 Techstream Lite (Green Cable) TSLP2DLR01 *Essential SST. NOTE Only ONE of the Techstream units listed above is required. Software version 15.20.016 or later is required. Additional Techstream units may be ordered by calling Approved Dealer Equipment (ADE) at 1-800-368-6787. © 2020 Toyota Motor Sales, USA T-SB-0120-20 December 11, 2020 Page 3 of 9 Replacement ECU Software Configure Process Operation Procedure 1. AFTER ECU replacement, connect Techstream, select the applicable vehicle and options, and select Next. Figure 1. © 2020 Toyota Motor Sales, USA T-SB-0120-20 December 11, 2020 Page 4 of 9 Replacement ECU Software Configure Process Operation Procedure (continued) 2. Perform a Health Check. During the Health Check, Techstream will automatically detect the replacement ECU needs configuration software. On the Health Check Results page, select Yes in the Configure column to begin the configuration software download process. Figure 2. © 2020 Toyota Motor Sales, USA T-SB-0120-20 December 11, 2020 Page 5 of 9 Replacement ECU Software Configure Process Operation Procedure (continued) 3. Login to TIS. Figure 3. 4. Enter a password for secondary authentication and select Login. Figure 4. 5. When the ECU Configure Software confirmation screen is displayed, return to Techstream. Figure 5. © 2020 Toyota Motor Sales, USA T-SB-0120-20 December 11, 2020 Page 6 of 9 Replacement ECU Software Configure Process Operation Procedure (continued) 6. Has the configuration software been previously downloaded? YES — Continue to step 7. NO — Select Next as shown in the figure below and continue to step 7. Figure 6. NOTE Selecting Output will display a list of the required configuration software for each ECU. This feature is available to print the list of required ECU software when needed. © 2020 Toyota Motor Sales, USA T-SB-0120-20 December 11, 2020 Page 7 of 9 Replacement ECU Software Configure Process Operation Procedure (continued) 7. Downloading the software may take several minutes. When the download is complete, select Next to start the Calibration Update Wizard (CUW). Figure 7. 8. Refer to Service Bulletin No. T-SB-0107-20 ECU Flash Reprogramming With Security Signature and complete the programming as instructed there. © 2020 Toyota Motor Sales, USA T-SB-0120-20 December 11, 2020 Page 8 of 9 Replacement ECU Software Configure Process Operation Procedure (continued) 9. When programing is complete, Techstream will send the updated vehicle information to TIS. Select Next. Figure 8. 10. Enter a password for secondary authentication and select Login. Figure 9. © 2020 Toyota Motor Sales, USA T-SB-0120-20 December 11, 2020 Page 9 of 9 Replacement ECU Software Configure Process Operation Procedure (continued) 11. Return to Techstream when the ECU Configure Software confirmation displays, as shown below. Figure 10. 12. Once Vehicle Information has been sent to TIS, select Exit, clear any DTCs that may have been set, and perform a final Health Check to confirm no additional software updates are available. Figure 11. © 2020 Toyota Motor Sales, USA