A71523

Page 1 of 9
ROADSTER 2014 Front Fuse Box Covers
Replacement, Update ECM Software P1614, Hi Temp,
Limp Home (RS, ST)_000071523_TST61Y014S00_en
Printable
Version
Summary:
Roadster Spyder RS and ST Series Subject 1 - Front Fuse Box Covers Replacement Subject 2 - Update ECM
Software P1614 Hi-Temp Lamps Limp Home Mode
Type:
General
TST Detail:
Campaign no.:
2014–0001
Publication date:
January 23, 2014
Subject:
Roadster Spyder™ RS and ST Series
Subject 1 - Front Fuse Box Covers Replacement
Subject 2 - Update ECM Software (P1614, Hi-Temp Lamps, Limp Home Mode)
YEAR
MODEL
Spyder RS
series
2014
Spyder ST
series
MODEL NUMBER
STD
SE5
A2EF, A2EH
S SE5
B1ED, B1EG, B1EH, B1EJ, B1EL, B1EM,
B1EN
S SM5
C1EJ
S SE5
C2ED, C2EE, C2EF, C2EH, C2EJ, C2EK
LTD
SE5
D4EA, D4EE
SERIAL
NUMBER
See Attached List
SUMMARY
Subject 1
An improved fuse box cover is now used in production. Since this was a running change, a very limited quantity of
vehicle were produced having a version of the fuse box cover which no longer meets BRP standards.
Replace fuse box covers.
Parts required
Order parts through the regular channel.
Description
Part Number
QTY
Right fuse box cover
710 004 180
1
Left fuse box cover
710 004 181
1
mhtml:file://C:\Users\simarma3\AppData\Local\Temp\1\Temp1_Article_Detail_TS new (...
10/3/2016
Page 2 of 9
Repair Tip
Perform the Fuse Box Covers Replacement, while ECM is updating.
Subject 2
Update ECM with latest version of software to correct the outlined problems.
- Code P1614 may be triggered and cause a limp home mode when starting the engine.
- The indicator lamp and message HI TEMP may appear at engine startup, even if unit is at normal operating
temperature.
- Engine heat felt by the driver may be uncomfortable.
NOTE: Updating the software may slightly improve riders comfort from heat in some riding conditions. The portion of
the update that addresses uncomfortable heat felt by the driver is applicable to non-CARB vehicles only.
PROCEDURE
Subject 1
1. Remove the cover from both fuse boxes.
2. Transfer fuses to new covers.
1. Old fuse box cover
2. New fuse box cover
3. Install new covers on fuse boxes. Make sure they are properly clipped.
Subject 2
Connect vehicle to the latest applicable B.U.D.S. version.
NOTE: The latest B.U.D.S. version is available on KNOWLEDGE CENTER. At time of writing, the latest B.U.D.S.
version was:
B.U.D.S. - R3.5.1 for Roadster
1. Click on "Advanced Search".
2. Select "Diagnostic Software".
3. In the KEYWORD(S) field, type in the B.U.D.S. single file number.
4. "SEARCH".
5. Identify and download proper file.
Please note that you can also type in the KEYWORD(S) field the B.U.D.S. single file number directly without going in
the "Advanced Search".
Computer and Vehicle Preparation
NOTICE
Continuous power to the computer and to the vehicle is mandatory during this operation or damage to a module
could occur.
Be sure to disable the computer screen saver.
mhtml:file://C:\Users\simarma3\AppData\Local\Temp\1\Temp1_Article_Detail_TS new (...
10/3/2016
Page 3 of 9
If using a portable computer, be sure to provide a continuous supply of electrical power by connecting it to a wall
outlet.
To ensure there is enough power to the vehicle electronic modules to complete the software updates, use a
portable power pack.
NEVER use a battery charger instead of portable power pack. The battery charger may cause electrical noise
causing problems during the update.
These software updates of the vehicle modules will take some time to complete and MUST NOT be interrupted.
Although computer screen may blank or may seem to freeze for a while, do NOT interrupt B.U.D.S. to allow
updates to be completed. Do not touch the PC.
Although the cluster will blank, do NOT interrupt B.U.D.S. to allow updates to be completed. Do not touch the
vehicle.
1. Ensure the vehicle battery is fully charged.
2. Connect a portable power pack (fully charged) to the vehicle battery.
CONNECTION AT BATTERY POSTS, BEHIND BATTERY ACCESS PANEL IN FRONT STORAGE
COMPARTMENT
B.U.D.S. Connections
1. Connect MPI before starting B.U.D.S. to ensure proper operation. Refer to the applicable SHOP MANUAL for
details:
- Section 03: ELECTRONIC MANAGEMENT SYSTEMS
- Subsection 03: COMMUNICATION TOOLS AND B.U.D.S.
Mandatory Tools
A personal computer (laptop or desktop)
MPI-2 INTERFACE CARD
(P/N 529 036 018)
mhtml:file://C:\Users\simarma3\AppData\Local\Temp\1\Temp1_Article_Detail_TS new (...
10/3/2016
Page 4 of 9
MPI-2 DIAGNOSTIC CABLE
(P/N 710 000 851)
OPTIONAL TOOL
Extension cable
available at electronic retail outlets.
Do not exceed 7.5 m (25 ft)
2. Start B.U.D.S. and logon.
3. Turn ignition key ON.
TYPICAL - IGNITION KEY ON
NOTE: If the following message does not automatically go away, click the RETRY button.
RETRY BUTTON
Compare number of modules shown in B.U.D.S. with following table.
EXAMPLE
Model
Number of Modules Connected
RS SM5
5
RS SE5
6
mhtml:file://C:\Users\simarma3\AppData\Local\Temp\1\Temp1_Article_Detail_TS new (...
10/3/2016
Page 5 of 9
ST SM5
6
ST SE5
7
NOTE: If a CAN Configuration Kit (CCK) is installed, the number of modules listed in B.U.D.S. will be increased by
one.
ECM Software Update
1. Click on READ DATA.
2. When the following message appears, click "Yes" to start the update.
ECM UPDATE CONFIRMATION - CLICK "YES"
3. If the following message appears, then there is "Active" or "Occurred" fault(s).
3.1 Clicking "OK" will prompt you to the FAULT screen.
3.2 Before proceeding with the update, fault codes relating to a current customer complain should be repaired; all
other fault codes should be cleared.
NOTE: The following top menu button will continue to flash until the ECM software update is performed.
ECM SOFTWARE UPDATE REMINDER
3.3 Click on "Important Update" to proceed.
ECM Software Update continued
NOTICE
While the ECM is being updated, an hour glass will appear on the computer. The computer
screen and cluster might also go blank. DO NOT TOUCH ANYTHING (PC and vehicle) until the following
message appears. Then, click the "OK" button.
mhtml:file://C:\Users\simarma3\AppData\Local\Temp\1\Temp1_Article_Detail_TS new (...
10/3/2016
Page 6 of 9
SUCCESSFUL ECM UPDATE CONFIRMATION - CLICK "OK"
4. When the following message appears, click "Yes".
CLUSTER SECURITY MATCHING REQUEST - CLICK "YES"
5. When the following message appears:
5.1 Turn ignition key to OFF.
5.2 Wait until the message vanishes.
6. When the following message appears, turn ignition key to ON then click the "OK" button.
7. The ECM software update is completed.
Update Validation
1. Click on READ DATA button.
READ DATA BUTTON
2. Check if the update has been successful.
MODULE, ECM, INFORMATION
3. Look at the "BRP Assembly Number", compare with list in table.
mhtml:file://C:\Users\simarma3\AppData\Local\Temp\1\Temp1_Article_Detail_TS new (...
10/3/2016
Page 7 of 9
TYPICAL
1. BRP Assembly number
ECM Information
BRP assembly number
420265381
420265386
420265380
420265385
4. If any number in the table is found in B.U.D.S., then the update was successful.
5. If a wrong number is found, repeat the update procedure.
TPS Reset
1. In B.U.D.S., click the items in the illustrated order.
Step 1:. Setting tab
Step 2:. ECM tab
Step 3:. Reset (TPS)
2. When the following message appears, click "OK".
mhtml:file://C:\Users\simarma3\AppData\Local\Temp\1\Temp1_Article_Detail_TS new (...
10/3/2016
Page 8 of 9
CLICK "OK"
Clearing Faults
1. In B.U.D.S., click on READ DATA.
READ DATA BUTTON
2. Click the items in the illustrated order.
CLEARING FAULTS
Step 1:. Faults
Step 2:. Click "Clear Occurred Faults" button
3. When the following message appears, click "Yes".
CONFIRM CLEAR FAULTS REQUEST - "YES"
NOTE: To clear all faults, it may be necessary turn the ignition key OFF, wait a few seconds, turn the ignition key
back ON and activate the CLEAR OCCURRED FAULTS button once more.
4. Turn ignition key OFF.
5. When the following message appears, turn ignition key to ON and wait until the message vanishes.
6. Click on the CLEAR OCCURRED FAULTS button again and ensure all faults are cleared.
7. Turn ignition key OFF.
NOTICE
To avoid potential vehicle damage, it is very important to turn ignition key off BEFORE
exiting B.U.D.S. or unplugging the MPI-2 diagnostic cable from the vehicle.
8. Unplug MPI-2 diagnostic cable from vehicle.
mhtml:file://C:\Users\simarma3\AppData\Local\Temp\1\Temp1_Article_Detail_TS new (...
10/3/2016
Page 9 of 9
WARRANTY
Submit a campaign claim using the following information.
For claiming procedure, refer to the DEALER/DISTRIBUTOR WARRANTY GUIDE.
Click in the REPAIR BOX while completing your claim on BOSSWeb.
Campaign Number
2014-0001
Claim Type
Campaign Claim
Action
Repair
Flat Rate Time
0.3 hour
Expiry date
January 19, 2017
For the serial number list of involved vehicles, please see attachment.
Attachment: VIN List_en.pdf
First Published By: Mélanie Bernard on 2014-01-29
Last Modified By: Mélanie Bernard on 2014-01-29
mhtml:file://C:\Users\simarma3\AppData\Local\Temp\1\Temp1_Article_Detail_TS new (...
10/3/2016