LTB01117NAS1

Page 1 of 5
LTB01117NAS1
TECHNICAL BULLETIN
02 NOV 2017
© Jaguar Land Rover North America, LLC
NOTE: The information in Technical Bulletins is intended for use by trained, professional
Technicians with the knowledge, tools, and equipment required to do the job properly and
safely. It informs these Technicians of conditions that may occur on some vehicles, or
provides information that could assist in proper vehicle service. The procedures should not be
performed by 'do-it-yourselfers'. If you are not a Retailer, do not assume that a condition
described affects your vehicle. Contact an authorized Land Rover service facility to determine
whether this bulletin applies to a specific vehicle.
INFORMATION
SECTION:
307-01: Automatic Transmission/Transaxle
SUBJECT/CONCERN:
No Drive After An Auto Stop/Start
AFFECTED VEHICLE RANGE:
https://topix.landrover.jlrext.com/topix/service/document/853188
11/8/2017
Page 2 of 5
MODEL
YEAR:
MODEL:
VIN:
ASSEMBLY
PLANT:
APPLICABILITY:
Discovery Sport
(LC)
2016-2017
516414721693
Halewood
Vehicles With: 9HP48 9-Speed
Automatic Transmission - AWD
Range Rover
Evoque (LV)
2016-2017
048210266718
Halewood
Vehicles With: 9HP48 9-Speed
Automatic Transmission - AWD
MARKETS:
NORTH AMERICA
CONDITION SUMMARY:
SITUATION:
No drive when the Transmission Control Switch (TCS) is in the Drive (D) position after an Auto
Stop/Start. The Drive (D) lamp will flash on the TCS and a 'Re-select gear to manoeuvre'
message will be displayed on the Instrument Cluster (IC).
CAUSE:
This may be caused by an Anti-lock Brake System (ABS) control module software error.
ACTION:
Should a customer express a concern, follow the Diagnostic Procedure below.
PARTS:
No Parts Required
TOOLS:
https://topix.landrover.jlrext.com/topix/service/document/853188
11/8/2017
Page 3 of 5




Jaguar Land
Rover-approved
Midtronics
battery power
supply
Jaguar Land
Rover-approved
diagnostic tool
with latest SDD
software,
Calibration File
WARRANTY:
NOTES:
◾ Repair procedures are under constant review, and therefore times are subject to
change; those quoted here must be taken as guidance only. Always refer to JLR
claims submission system to obtain the latest repair time.
◾ The JLR Claims Submission System requires the use of causal part numbers. Labor
only claims must show the causal part number with a quantity of zero.
DESCRIPTION
Anti-Lock Brake System (ABS) control
module - Update ECU
SRO
70.90.89.31
TIME
(HOURS)
0.2
CONDITION
CODE
42
CAUSAL
PART
LR079449
NOTE:
Normal Warranty procedures apply.
DIAGNOSTIC PROCEDURE 'A': SDD
https://topix.landrover.jlrext.com/topix/service/document/853188
11/8/2017
Page 4 of 5
This Diagnostic Procedure is only for vehicles requiring the Jaguar Land Rover-approved
diagnostic tool with Symptom Driven Diagnostics (SDD).
CAUTIONS:
◾ A Jaguar Land Rover-approved Midtronics battery power supply must be connected
to the vehicle battery during diagnosis / module programming.
◾ All ignition ON/OFF requests must be carried out. Failure to perform these steps may
cause damage to control modules in the vehicle.
1
Connect the Jaguar Land Rover-approved Midtronics battery power supply to the
vehicle battery.
2
NOTE:
The Jaguar Land Rover-approved diagnostic tool must be loaded with
DVD151.02 Calibration File 280 (or later).
Connect the Jaguar Land Rover-approved diagnostic tool to the vehicle and begin a
new session.
3
Follow the on-screen prompts, allowing the diagnostic tool to read the VIN, identify
the vehicle, and initiating the data collect sequence.
4
If the hyperlink is not available:
1
Select Diagnosis from the Session Type screen.
2
Select the Selected Symptoms tab.
3
Select one of the following symptoms:
Powertrain - Automatic transmission and transaxle - Automatic
transmission and transaxle symptoms - Gear selector malfunction Gear position display flashing
4
Select continue.
https://topix.landrover.jlrext.com/topix/service/document/853188
11/8/2017
Page 5 of 5
5
Select the Recommendations tab.
6
Select Run to perform the 'Configure existing module - ABS control module'
option.
5
Follow all on-screen instructions until the application completes successfully.
1
When prompted, select the Clear DTCs option following completion of the
software download.
2
6
7
When all tasks are complete, go to the next Step.
Exit the current session.
1
Select the Session tab.
2
Select the Close Session option.
Disconnect the diagnostic tool and battery power supply from the vehicle.
https://topix.landrover.jlrext.com/topix/service/document/853188
11/8/2017