JLRTB02037NAS1

Service Bulletin Details

Public Details for: JLRTB02037NAS1

Dust collects on the door shut surfaces and is drawn into the passenger compartment bythe inward airflow when a door is opened.


- 2021 - 2020 - 2019 -

Models from 2021
2021 JAGUAR I-PACE
Models from 2020
2020 JAGUAR I-PACE
Models from 2019
2019 JAGUAR I-PACE 
3/2/2021
TECHNICAL BULLETIN
JLRTB02037NAS1
TECHNICAL BULLETIN
03 NOV 2020
© Jaguar Land Rover North America, LLC
NOTE: The information in Technical Bulletins is intended for use by trained, professional
Technicians with the knowledge, tools, and equipment required to do the job properly and
safely. It informs these Technicians of conditions that may occur on some vehicles, or
provides information that could assist in proper vehicle service. The procedures should not
be performed by 'do-it-yourselfers'. If you are not a Retailer, do not assume that a condition
described affects your vehicle. Contact an authorized Land Rover service facility to
determine whether this bulletin applies to a specific vehicle.
INFORMATION
SECTION:
501-03
SUBJECT/CONCERN:
Dust Entering The Passenger Compartment
AFFECTED VEHICLE RANGE:
MODEL:
MODEL YEAR:
VIN:
ASSEMBLY PLANT:
I-PACE (X590)
2019-2020
F60145-F81898
Graz (Austria)
I-PACE (X590)
2020 Onwards
600001 Onwards
Graz (Austria)
MARKETS:
NORTH AMERICA
https://www.odyssey.jlrint.com/odyssey/WorkflowHtmlComposition.do?wid=1614689426851
1/10
3/2/2021
TECHNICAL BULLETIN
CONDITION SUMMARY:
SITUATION:
Dust can be found entering the passenger compartment when the doors are opened. The
dust can be found on the second row seats, tread plates and lower C-pillar molding.
CAUSE:
Dust collects on the door shut surfaces and is drawn into the passenger compartment by
the inward airflow when a door is opened.
ACTION:
Follow the instructions below.
PARTS:
NOTES:
An allowance equivalent to $12.00 US has been allocated to locally source 4
sachets of 3M™ Adhesion Promoter 06396 (or equivalent) and 2 sachets of 3M™
surface cleaner (or equivalent), per vehicle.
1 sachet of 3M™ Adhesion Promoter 06396 (or equivalent) is required for each
door.
1 sachet of 3M™ surface cleaner (or equivalent) will clean the surface of 2 doors.
PART NUMBER
DESCRIPTION
QUANTITY
T4K15466
Front door - Lower seal kit
1
T4K15467
Rear door - Lower seal kit
1
ZZZ001
4 sachets of 3M™ Adhesion Promoter 06396 and 2
sachets of 3M™ surface cleaner (or equivalents)
$12.00
WARRANTY:
https://www.odyssey.jlrint.com/odyssey/WorkflowHtmlComposition.do?wid=1614689426851
2/10
3/2/2021
TECHNICAL BULLETIN
NOTES:
Repair procedures are under constant review, and therefore times are subject to
change; those quoted here must be taken as guidance only. Use TOPIx to obtain
the latest repair time.
The JLR claims submission system requires the use of causal part numbers. Labor
only claims must show the causal part number with a quantity of zero.
DESCRIPTION
JLRTB02037 - Lower door seal - Install Vehicle set
SRO
TIME
(HOURS)
CONDITION
CODE
CAUSAL
PART
99.01.11
0.5
49
T4K1398
NOTE:
Normal Warranty procedures apply.
SERVICE INSTRUCTION - FRONT DOOR
1.
Raise and support the vehicle (see TOPIx Workshop Manual section 100-02:
Jacking and Li ing - Description and Operation - Jacking and Li ing).
2.

Open the front right door.
https://www.odyssey.jlrint.com/odyssey/WorkflowHtmlComposition.do?wid=1614689426851
3/10
3/2/2021
TECHNICAL BULLETIN
3.
NOTE:
Allow a minimum of 60 seconds for the 3M™ surface cleaner (or equivalent)
to dry before continuing to step 4.

Using 3M™ surface cleaner (or equivalent), clean the inside edge of the front right
door lower molding, as shown highlighted in the illustration.
https://www.odyssey.jlrint.com/odyssey/WorkflowHtmlComposition.do?wid=1614689426851
4/10
3/2/2021
TECHNICAL BULLETIN
4.
NOTE:
Allow a minimum of 90 seconds for the 3M™ adhesion promoter (or
equivalent) to dry before continuing to step 5.

Following the manufactures specifications, apply the 3M™ adhesion promoter (or
equivalent) to the inside edge of the front right door lower molding, as shown
highlighted in the illustration.
https://www.odyssey.jlrint.com/odyssey/WorkflowHtmlComposition.do?wid=1614689426851
5/10
3/2/2021
TECHNICAL BULLETIN
5.
NOTES:
Make sure the new front right door lower seal is installed following the
contour of the front right door lower molding.
Do not completely remove the adhesive backing before installing the new
front right door lower seal.

Gradually remove the adhesive backing and install the new front right door lower
seal in small sections at a time. Apply firm pressure along the entire length of the
lower seal to make sure the adhesive is bonded to the front right door lower
molding.
6.
NOTE:
Do not expose the new front right door lower seal to water for a minimum
of 24 hours.
Close the front right door and allow a minimum time of 20 minutes, at 21°C (70°F),
for the adhesive to bond.
7.
Repeat the steps 2 to 6 for the front le door and then continue to 'Service
Instruction - Rear Door'.
https://www.odyssey.jlrint.com/odyssey/WorkflowHtmlComposition.do?wid=1614689426851
6/10
3/2/2021
TECHNICAL BULLETIN
SERVICE INSTRUCTION - REAR DOOR
1.

Open the rear right door.
https://www.odyssey.jlrint.com/odyssey/WorkflowHtmlComposition.do?wid=1614689426851
7/10
3/2/2021
TECHNICAL BULLETIN
2.
NOTE:
Allow a minimum of 60 seconds for the 3M™ surface cleaner (or equivalent)
to dry before continuing to step 3.

Using 3M™ surface cleaner (or equivalent), clean the inside edge of the rear right
door lower molding, as shown highlighted in the illustration.
https://www.odyssey.jlrint.com/odyssey/WorkflowHtmlComposition.do?wid=1614689426851
8/10
3/2/2021
TECHNICAL BULLETIN
3.
NOTE:
Allow a minimum of 90 seconds for the 3M™ adhesion promoter (or
equivalent) to dry before continuing to step 4.

Following the manufactures specifications, apply the 3M™ adhesion promoter (or
equivalent) to the inside edge of the rear right door lower molding, as shown
highlighted in the illustration.
https://www.odyssey.jlrint.com/odyssey/WorkflowHtmlComposition.do?wid=1614689426851
9/10
3/2/2021
TECHNICAL BULLETIN
4.
NOTES:
Make sure the new rear right door lower seal is installed following the
contour of the rear right door lower molding.
Do not completely remove the adhesive backing before installing the new
rear right door lower seal.

Gradually remove the adhesive backing and install the new rear right door lower
seal in small sections at a time. Apply firm pressure along the entire length of the
lower seal to make sure the adhesive is bonded to the rear right door lower
molding.
5.
NOTE:
Do not expose the new rear right door lower seal to water for a minimum of
24 hours.
Close the rear right door and allow a minimum time of 20 minutes at 21°C (70°F)
for the adhesive on the bond.
6.
Repeat the steps 1 to 5 for the rear le door.
7.
Lower the vehicle.
https://www.odyssey.jlrint.com/odyssey/WorkflowHtmlComposition.do?wid=1614689426851
10/10

© dot.report 2024

Use of this information constitutes acceptance for use in an AS IS condition. There are NO warranties, implied or otherwise, with regard to this information or its use. Any use of this information is at the user's risk. It is the responsibility of user to evaluate the accuracy, completeness or usefulness of any information, opinion, advice or other content. EACH USER WILL BE SOLELY RESPONSIBLE FOR ANY consequences of his or her direct or indirect use of this web site. ALL WARRANTIES OF ANY KIND ARE EXPRESSLY DISCLAIMED. This site will NOT BE LIABLE FOR ANY DIRECT, INDIRECT or any other kind of loss.