NTB10068E

Reference:
Dat e:
NTB10-068e
January 28, 2013
VOLUNTARY SERVICE CAMPAIGN
NISSAN NAVIGATION SOFTWARE UPDATE
This bulletin has been amended. Changes have been made throughout to accommodate a new
reprogramming disc. Please discard previous versions of this bulletin.
CAMPAIGN ID #: P0337
2010 Altima Sedan, Coupe, and Hybrid (L32, CL32, and L32HV)
APPLIED
VEHICLES:
2010 Maxima (A35)
2010 370Z Coupe and Roadster (Z34 and HZ34)
2011 GT-R (R35)
Check Service Comm to confirm campaign eligibility.
INTRODUCTION
On the Applied Vehicles listed above, the navigation, mobile phone, and iPod® functions
may not be working as intended. To remedy this potential condition, Nissan is conducting
this voluntary service campaign to update the navigation software at no charge for parts or
labor.
IDENTIFICATION NUMBER
Nissan has assigned identification number P0337 to this campaign. This number must
appear on all communications and documentation of any nature dealing with this campaign.
DEALER RESPONSIBILITY
Dealers are to repair vehicles falling within range of this campaign that enter the service
department. This includes vehicles purchased from private parties, vehicles presented by
transient (tourists) owners, and vehicles in a dealer’s inventory.
1/19
REPROGRAMMING SOFTWARE DVDs - REQUIRED FOR THIS PROCEDURE
•
Discs 1/3 and 2/3 of the set shown in Figure A are used for all applied models
in this campaign except GT-R.
•
Do not use disc 3/3.
DO NOT
USE
Figure A
•
This NEW disc (Figure B) is
required for all applied models in
this campaign.
•
This disc replaces disc 3/3 above.
•
This disc also replaces disc
NTB10-125b/ITB10-066b (disc 1/1)
and disc NTB10-068 (disc1/1) for
GT-R.
NOTE: Numbers on these discs do
not match this bulletin’s reference
number or the campaign ID #.
Figure B
•
Each dealer was previously mailed the discs listed above, free of charge, from
Clarion.
•
Should you require additional discs due to loss or damage, the discs can be ordered,
free of charge, by contacting Clarion at the toll free number 1-(800) 347-8933.
Request a new disc using the information printed on the disc.
2/19
NTB10-068e
SERVICE PROCEDURE
IMPORTANT: Before loading the Reprogram Discs, make sure to Disable Bluetooth®
function otherwise the Navigation System may continuously reboot the next time it is
turned on.
NOTE: This procedure will take about 30 minutes with the ignition ON. Before starting,
make sure to attach a battery charger to the vehicle battery set to a low charge rate
(trickle charge).
This SERVICE PROCEDURE contains three sections:
A. Disable Bluetooth® Function (page 3)
B. Loading the Program - all except GT-R (Page 5)
Loading the Program for GT-R (page 13)
C. Check Bluetooth® Setting - all except GT-R (page 12)
Check Bluetooth® Setting for GT-R (page 17)
A: Disable Bluetooth® Function
1. Set the parking brake.
2. Turn the ignition ON and keep the transmission in Park or Neutral.
3. Make sure there is no disc in the CD/DVD slot (eject any disc that may be in the
CD/DVD player).
4. Press the “SETTING” button on the switch panel.
3/19
NTB10-068e
Bluetooth
5. Touch “Bluetooth”.
Figure 1
6. Make sure Bluetooth is OFF.
•
Touching Bluetooth will change the
setting ON > OFF or OFF > ON.
Bluetooth ON
Figure 2
•
Bluetooth is OFF when the ON
indicator is “grayed-out”.
Bluetooth OFF
Figure 3
7. Turn the ignition OFF and wait for 10 seconds.
8. Go to B: Loading the Program on the next page.
4/19
NTB10-068e
B: Loading the Program – all except GT-R
For GT-R, go to page 13.
NOTE: This procedure will take about 30 minutes with the ignition ON. Before starting,
make sure to attach a battery charger to the vehicle battery set to a low charge rate
(trickle charge).
1. Turn the ignition ON – keep the transmission in Park or Neutral.
•
The navigation start-up screen should display.
NOTE: If the navigation start-up screen is not displayed; turn the ignition OFF, wait
10 seconds, and then turn the ignition ON again.
2. Wait for more than 1 minute.
3. Press the “INFO” button on the switch panel.
Navigation
Version
4. Select “Navigation Version” on the
display screen.
Figure 4
NOTE: On some vehicles you will need
to select “Others” to find “Navigation
Version”.
Others
Figure 5
5/19
NTB10-068e
5. Check “Map Version”.
•
If the Map Version is 09-10 MAP No.1
or
Map version
09-10 MAP No.1a
a. Continue with Step 6.
•
Figure 6
If the Map Version is any other then
above:
a. Insert the new disc
NTB12-070 / ITB12-054 (Disc 1/1)
into the in-dash CD / DVD player.
The other Discs will not be
needed.
b. Skip to step 18 on page 8.
6. Make sure there is no disc in the CD/DVD slot (eject any disc that may be in the
CD/DVD player).
7. Insert disc ITB10-031 / NTB10-068 (Disc1/3) into the in-dash CD/DVD player.
•
For Altima; open the display by pressing the OPEN/TILT button to access the disc
slot. Leave the display open while loading.
IMPORTANT: Once reprogramming has started:
•
Do not eject a disc while it is loading.
•
Do not change the ignition position until all discs have been loaded.
•
Make sure all 3 discs have been loaded into the CD/DVD player before stopping
the procedure.
8. Wait for the program to load (progress bar will display).
6/19
NTB10-068e
9. When the program has finished loading:
•
Disc will automatically eject, and
•
“Program loading is completed” will display.
Figure 7
10. Carefully remove the disc.
11. The navigation system will automatically restart.
12. When the message ”Please insert Disc 2/3”
displays, insert disc
ITB10-031 / NTB10-068 (Disc 2/3).
Figure 8
13. Touch “DVD update”.
Figure 9
14. Touch “Yes” to begin the map update process.
•
Map update will take about 15 minutes.
Figure 10
7/19
NTB10-068e
15. When “Eject the DVD to let the system reboot” is
displayed, eject Disc 2/3.
16. The navigation system will automatically restart.
Figure 11
17. When the message ”Please insert Disc 3/3”
displays, insert the new disc
NTB12-070 / ITB12-054 (Disc 1/1).
Figure 12
18. With DVD disc NTB12-070 / ITB12-054 (Disc 1/1) inserted, one of the following screens
will display:
•
If the screen in Figure 13 is displayed,
this disc is not needed.
¾ Remove/eject the DVD from the
CD slot.
¾ Go to C: Check Bluetooth®
Setting on page 12.
Figure13
•
If “Now preparing loading” shown in
Figure 14 is displayed,
reprogramming will begin
automatically.
¾ Follow the on-screen Caution
during the reprogram.
Figure 14
8/19
NTB10-068e
19. During the first part of the update
process, 3 more screens will be
displayed along with a percentage of
completion (progress) bars:
•
Rewriting boot data. (Figure 15)
•
Rewriting program data (Figure 16)
•
Rewriting language data (Figure 17)
Figure 15
IMPORTANT:
Once the reprogramming has started:
•
Do not eject the DVD while it is
loading.
•
Do not change the ignition position
until the DVD has been loaded.
Figure 16
Figure 17
20. When the first part of the program has
finished loading:
•
“Program loading is completed” will
be displayed (Figure 18).
•
The Re-programming Software DVD
will automatically eject.
21. Remove the DVD and continue to the
second part of the update (step 22).
Figure 18
9/19
NTB10-068e
22. After the DVD is removed, the screen
in Figure 19 (“Please insert disc”) may
ask to reinstall the same Reprogramming Software DVD for a
second time.
•
If not (Navigation System restarts),
go to step 25 on the next page.
•
If so, re-insert DVD disc.
¾ At the top of the screen
“Program Loading (2nd)” will be
displayed.
Figure 19
23. “Rewriting boot data” (Figure 20) and
“Rewriting program data” (Figure 21)
will be displayed.
IMPORTANT:
Once reprogramming has started:
Figure 20
•
Do not eject the DVD while it is
loading.
•
Do not change the ignition position
until the DVD has been loaded.
Figure 21
24. After the reprogram has completed:
•
“Program loading is completed” will
be displayed (Figure 22).
•
The Re-programming Software
DVD will automatically eject.
•
The Navigation system will restart.
•
Proceed to step 25.
Figure 22
10/19
NTB10-068e
After Navigation has restarted:
25. To confirm that the Navigation version has been successfully updated, load DVD disc
NTB12-070 / ITB12-054 (Disc 1/1) back into the CD slot again.
One of the following screens will display:
•
If Figure 23 is displayed, it indicates
that the reprogram has been
completed.
¾ If complete, go to step 26.
Figure 23
•
If Figure 24 is displayed, the update
did not complete. Allow the update to
complete:
¾ Go back to step 18 on page 8.
¾ Follow steps 18 through 25 again.
Figure 24
26. Eject the DVD.
27. Go to C: Check Bluetooth® Setting on the next page.
11/19
NTB10-068e
C: Check Bluetooth® Setting (all except GT-R)
1. Press the “Setting” button on the switch panel.
2. Touch “Bluetooth”.
Bluetooth
Figure 28
3. Make sure Bluetooth is set to the
customer’s setting (as it was before
starting the procedure).
•
Touching Bluetooth will change the
setting ON > OFF or OFF > ON.
•
Bluetooth is ON when the ON
indicator displays in orange.
Bluetooth ON
Figure 29
•
Bluetooth is OFF when the ON
indicator is “grayed-out”.
Bluetooth OFF
Figure 30
4. Turn the ignition OFF. The process is complete.
12/19
NTB10-068e
B: Loading the Program for GT-R
1. Turn the ignition ON.
2. Wait for more than 1 minute.
3. Press the “INFO” button on the switch panel.
4. Make sure there is no disc in the CD/DVD slot (eject any disc that may be in the
CD/DVD player).
5. Load the new disc “NTB12-070/ITB12-054 Re-programming Software” DVD into CD
slot of the audio unit.
One of the following screens will display:
•
If the screen in Figure A1 is displayed,
this disc is not needed.
¾ Remove/eject the DVD from the
CD slot.
¾ Go to Check Bluetooth® Setting
for GT-R on page 17.
FigureA1
•
If “Now preparing loading” shown in
Figure A2 is displayed,
reprogramming will begin
automatically.
¾ Follow the on-screen Caution
during the reprogram.
Figure A2
13/19
NTB10-068e
6. During the first part of the update
process, 3 more screens will be
displayed along with a percentage of
completion (progress) bars:
•
Rewriting boot data. (Figure A3)
•
Rewriting program data (Figure A4)
•
Rewriting language data (Figure A5)
Figure A3
IMPORTANT:
Once the reprogramming has started:
•
Do not eject the DVD while it is
loading.
•
Do not change the ignition position
until the DVD has been loaded.
Figure A4
Figure A5
7. When the first part of the reprogram has
finished loading:
•
“Program loading is completed” will
be displayed (Figure A6).
•
The Re-programming Software DVD
will automatically eject.
8. Remove the DVD and continue to the
second part of the update (step 9).
Figure A6
14/19
NTB10-068e
9. After the DVD is removed, the screen
in Figure A7 (Please insert disc) may
ask to reinstall the same Reprogramming Software DVD for a
second time.
•
If not (Navigation System restarts),
go to step 12 on the next page.
•
If so, re-insert DVD disc.
¾ At the top of the screen
“Program Loading (2nd)” will be
displayed.
Figure A7
10. “Rewriting boot data” and “Rewriting
program data” will be displayed once
the DVD is reinstalled.
IMPORTANT:
Once reprogramming has started:
Figure A8
•
Do not eject the DVD while it is
loading.
•
Do not change the ignition position
until the DVD has been loaded.
Figure A9
11. After the reprogram has completed:
•
“Program loading is completed” will
be display (Figure A10).
•
The Re-programming Software
DVD will automatically eject.
•
The Navigation system will restart.
•
Proceed to step 12.
Figure A10
15/19
NTB10-068e
After Navigation has restarted:
12 To confirm that the Navigation version has been successfully updated, load DVD disc
NTB12-070 / ITB12-054 (Disc 1/1) back into the CD slot again.
One of the following screens will display:
•
If Figure A11 is displayed it, indicates
that the reprogram has been
completed.
¾ If complete go to step 13.
Figure A11
•
If Figure A12 is displayed, the update
did not complete. Allow the update to
complete:
¾ Go back to step 5 on page 13.
¾ Follow steps 6 through 12 again.
Figure A12
13. Eject the DVD.
14. Go to C: Check Bluetooth® Setting for GT-R on the next page.
16/19
NTB10-068e
C: Check Bluetooth® Setting for GT-R
1. Press the “Setting” button on the switch panel.
2. Touch “Bluetooth”.
Bluetooth
Figure A13
3. Make sure Bluetooth is set to the
customer’s setting (as it was before
starting the procedure).
•
Touching Bluetooth will change the
setting ON > OFF or OFF > ON.
•
Bluetooth is ON when the ON
indicator displays in orange.
Bluetooth ON
Figure A14
•
Bluetooth is OFF when the ON
indicator is “grayed out”.
Bluetooth OFF
Figure A15
4. Turn the ignition OFF. The process is complete.
17/19
NTB10-068e
CLAIMS INFORMATION
Submit a Campaign (CM) line claim using the following claims coding:
“CM” I.D.: P0337
CAMPAIGN ID
P0337
DESCRIPTION
Perform Navigation Reprogramming
18/19
OP CODE
P03370
FRT
0.3 hrs
NTB10-068e
OWNER’S LETTER (example of typical owner’s letter)
Dear Nissan Altima Sedan Owner:
Nissan is committed to providing the highest levels of product, quality and customer
satisfaction. With that in mind, we want to bring to your attention important information
about the Navigation, Communication and Entertainment Systems in your model year 2010
Altima Sedan vehicle.
REASON FOR CAMPAIGN
Nissan has become aware of customer concerns with the Navigation System and with
Communication and Entertainment Functions involving the iPhone. To help address these
concerns, Nissan will update the Navigation and communication software in your vehicle.
This software update will address irregularities with navigational maps, voice recognition
commands, phone book transfer from mobile phone to vehicle and increase the number of
entries that can be stored.
In addition, Nissan is aware of customer complaints regarding compatibility with the iPod
Touch. Apple has addressed this issue, and updated software for the iPod Touch is
available on the Apple website in July. Nissan has also developed a fix that will also be
installed when you bring your vehicle for this service.
WHAT NISSAN WILL DO
To assure your continued satisfaction and confidence in your model year 2010 Altima
Sedan, Nissan will reprogram the operating software to correct these conditions. This
service, free for parts and labor, should take less than 1 hour to complete, but your Nissan
dealer may require your vehicle for a longer period of time based upon their work schedule.
Please contact your Nissan dealer to perform this important service.
WHAT YOU SHOULD DO
Contact your Nissan dealer at your earliest convenience in order to arrange an
appointment. To ensure the least inconvenience for you, it is important that you have
an appointment before bringing your vehicle to the Nissan dealer for service. Please
bring this notice with you when you keep your service appointment. Instructions have been
sent to your Nissan dealer.
If the dealer fails, or is unable to complete the service free of charge, you may contact the
National Consumer Affairs Department, Nissan North America, Inc., P.O. Box 685003,
Franklin, TN 37068-5003. The toll free number is 1-800-NISSAN1 (1-800-647-7261).
Thank you for providing us an opportunity to ensure on-going satisfaction with your Nissan.
19/19
NTB10-068e