ITB13008

Classificatio n:
Referen ce:
Date:
FA12-006
ITB13-008
March 22, 2013
2009-2013; CLICKING NOISE FROM FRONT OR REAR AXLE
DURING TAKE-OFF/ACCELERATION
APPLIED VEHICLES:
2011 – 2013 M37/M56 (Y51)
2012 – 2013 M Hybrid (HY51)
2009 – 2013 G37 Sedan (V36)
2011 – 2012 G25 Sedan (V36)
2009 – 2013 G37 Coupe (CV36)
2009 – 2013 G37 Convertible (HV36)
2009 – 2013 FX35/FX37 (S51)
2009 – 2013 FX50 (S51)
2009 – 2013 EX35/EX37 (J50)
2011 – 2013 QX56 (Z62)
2013
JX (L50)
IF YOU CONFIRM:
Customers concern of a “clicking” noise coming from either left or right front/rear axles during takeoff/acceleration.
ACTION:
Apply Molykote M77 grease (P/N 44003-7S000) to the hub bearing surfaces.
NOTE:
• Do not remove the axle from the hub or transmission for this bulletin.
•
Refer to the Electronic Service Manual (ESM) for model specific torque specifications.
IMPORTANT: The purpose of “ACTION” (above) is to give you a quick idea of the work you will be performing.
You MUST closely follow the entire Service Procedure as it contains information that is essential to successfully
completing the repair.
Infiniti Bulletins are intended for use by qualified technicians, not 'do-it-yourselfers'. Qualified technicians are properly trained
individuals who have the equipment, tools, safety instruction, and know-how to do a job properly and safely. NOTE: If you believe
that a described condition may apply to a particular vehicle, DO NOT assume that it does. See your Infiniti dealer to determine if this
applies to your vehicle.
1/3
PARTS INFORMATION
DESCRIPTION
PART NUMBER
QUANTITY
Cotter Pin
40073-0L700
As Needed
Molykote M77 Grease
44003-7S000
As Needed *
Nut-Lock, Wheel Bearing
(1)
As Needed (2)
* Order from your local Parts Distribution Center (PDC).
(1) Refer to the Electronic Parts Catalogue (FAST or equivalent) for model specific part number.
(2) Refer to Electronic Service Manual for replacement requirements.
NOTE: P/N 44003-7S000 is considered a shop supply – DO NOT include it on your warranty claim.
CLAIMS INFORMATION
Submit a Primary Part (PFP) line claim using the following claims coding:
One Side
DESCRIPTION
PFP
OP CODE
APPLY GREASE TO BEARING SURFACE (ON CAR,
MX22AA
(1)
ONE SIDE)
(1) Reference the FAST part catalog and use hub bearing part number as the PFP.
SYM
DIA
FRT
ZL
21
0.5
SYM
DIA
FRT
ZL
21
0.7
Both Sides
DESCRIPTION
PFP
OP CODE
APPLY GREASE TO BEARING SURFACE (ON CAR,
MX23AA
(1)
BOTH SIDE)
(1) Reference the FAST part catalog and use hub bearing part number as the PFP.
2/3
ITB13-008
SERVICE PROCEDURE
NOTE: The photos in this procedure are examples and may not look exactly like the vehicle you are
working on.
Lock Nut
1. Remove the front or rear (depending on model)
wheel bearing Cotter Pin and Lock Nut from the
axle.
NOTE: Do not remove the axle from the hub or
transmission for this bulletin.
Cotter pin
Figure 1
2. Push axle back to allow application of
Molykote M77 Grease.
3. Apply a moderate coat of Molykote (P/N
44003-7S000) to the entire (front or rear)
wheel hub bearing surface (see Figure 2).
Bearing surface
4. Re-install the (front or rear) wheel bearing
Lock Nut and Cotter Pin per the Service
Manual instructions.
5.
Figure 2
•
Refer to model specific ESM for Lock Nut replacement requirements.
•
Refer to the model specific ESM for wheel bearing Lock Nut torque specifications.
Test drive the vehicle to confirm the incident is resolved.
3/3
ITB13-008