NTB13008

Classification:
Reference:
EL12-003
Date:
NTB13-008
June 17, 2013
2007-2012 SENTRA; STEERING WHEEL SWITCH
SERVICE PARTS
APPLIED VEHICLES:
2007-2012 Sentra (B16)
SERVICE INFORMATION
If you confirm there is a need to replace the steering wheel switches on an Applied Vehicle
for any reason:
•
Do not replace the driver air bag module. The steering wheel switches are now
available as a separate service part.
•
Refer to the Service Procedure in this bulletin for steering wheel switch removal and
installation instructions.
Cruise Control
switches only
Audio & Cruise
Control switches
Steering Wheel Switch Service Parts
Nissan Bulletins are intended for use by qualified technicians, not 'do-it-yourselfers'. Qualified technicians are
properly trained individuals who have the equipment, tools, safety instruction, and know-how to do a job
properly and safely. NOTE: If you believe that a described condition may apply to a particular vehicle, DO
NOT assume that it does. See your Nissan dealer to determine if this applies to your vehicle.
1/7
PARTS INFORMATION
DESCRIPTION
PART NUMBER
QUANTITY
SW ASSY-STRG
Reference an electronic parts
catalog (FAST or equivalent) for
the part number applicable to
your vehicle
1
Bolt (for driver air bag module)
01121-0030U
2
Tapping Screw
01461-0013U
4*
*Only 2 Tapping Screws are needed if the steering wheel is not equipped with audio
switches.
CLAIMS INFORMATION
Please refer to the Online Warranty Flat Rate Manual.
SERVICE PROCEDURE
IMPORTANT: Follow all cautions, warnings, and notes in the Electronic Service
Manual (ESM) when working on or near a Supplemental Restraint System (SRS),
such as an airbag.
1. Write down all radio station presets.
Presets
1
2
3
4
5
6
A
B
C
SAT
2. Disconnect both battery cables, negative cable first.
3. After disconnecting the battery cables, wait at least three minutes before proceeding
with step 4.
2/7
NTB13-008
4. Remove the Driver Air Bag Module.
• Refer to section SRS, Driver Air Bag Module > Removal and Installation in the
applicable ESM for removal instructions.
5. Disconnect the horn connector. See Figure 1.
6. Using a suitable tool, gently pry open the three (3) harness retaining clips and release
the harness. See Figure 1.
Disconnect horn
connector
Release
harness
Open
clip
Open clips
Figure 1
3/7
NTB13-008
7. Remove the steering wheel switch screws.
• Remove four (4) screws if the steering wheel is equipped with audio switches.
• Remove two (2) screws if the steering wheel is not equipped with audio switches.
Audio & Cruise
Control switches
Cruise Control
switches only
Remove 4 screws
Remove 2 screws
Figure 2
Figure 3
Tab
8. Detach the steering wheel switches from
the driver air bag module by releasing
the tabs.
• Each steering wheel switch part
(RH or LH) has two (2) tabs.
Tab
• To release the tabs, pull the edge of
the steering wheel switch part away
from the air bag module.
Pull
Figure 4
4/7
NTB13-008
9. Attach the new steering wheel swiches to the driver air bag module.
NOTE: Make sure all tabs (2 tabs per steering switch part) are aligned and have
clicked/locked into place.
Cruise Control
switches only
Audio & Cruise
Control switches
Figure 5
Figure 6
10. Install the new steering wheel switch screws listed in the Parts Information section. See
Figures 2 and 3 for location of screws.
• DO NOT overtighen.
No gap
11. Confirm there are no gaps
between the driver air bag
module and the steering
wheel switches.
Figure 7
5/7
NTB13-008
12. Route the harness through the three (3) retaining clips and close the retaining clips.
13. Reconnect the horn connector.
Reconnect
horn connector
Route
harness
through clips
Close
clip
Close clips
Figure 8
14. Reinstall the Driver Air Bag Module.
• Refer to section SRS, Driver Air Bag Module > Removal and Installation in the
applicable ESM for installation instructions.
• For instructions on how to install the direct-connect SRS connectors, refer to section
SRC, Supplemental Restraint System > Direct-connect SRS Component
Connectors in the applicable ESM.
6/7
NTB13-008
15. Reconnect the battery cables, negative cable last.
16. Perform SRS operation check.
•
Refer to section SRC, Trouble Diagnosis > SRS Operation Check for
instructions.
17. Reset the radio station presets.
7/7
NTB13-008