ITB14017A
Service Bulletin Details
Public Details for: ITB14017A
Service information multi a/v configuration using consult-iii plus (c-iii plus) there are many configurations of the infiniti intouch system. Typically, if the multi a/v is not configured properly on a navi equipped vehicle, you will
Models from 2015
2015 INFINITI Q50 |
Models from 2014
2014 INFINITI Q50 |
Classification: Reference: EL14-017a Date: ITB14-017a January 2, 2015 2014 – 2015 Q50; CONFIGURING INFINITI INTOUCH SYSTEM This bulletin has been amended to include the 2015 model year. Please discard the previous version. APPLIED VEHICLE 2014 - 2015 Q50 (V37) 2014 - 2015 Q50 Hybrid (V37) SERVICE INFORMATION MULTI A/V Configuration using CONSULT-III plus (C-III plus) There are many configurations of the Infiniti InTouch system. Typically, if the MULTI A/V is not configured properly on a navigation equipped vehicle, you will see a clock with no hands on the upper display. If in a situation where the MULTI A/V needs to be manually configured, here are some tips in selecting the correct configuration: Navigation: Is there is a MAP button on the Infiniti Controller (Figure 1)? Yes, select WITH No, select WITHOUT Lane Departure Prevention: Vehicle with Navigation Is it there is a Blind Spot Warning Light on the APillar? Infiniti Controller Yes, select ON. Figure 1 No, select OFF Hybrid: Select OFF for Conventional Engine. Select FR TYPE for 2WD Hybrid Select FR TYPE 4WD for 4WD Hybrid Infiniti Bulletins are intended for use by qualified technicians, not 'do-it-yourselfers'. Qualified technicians are properly trained individuals who have the equipment, tools, safety instruction, and know-how to do a job properly and safely. NOTE: If you believe that a described condition may apply to a particular vehicle, DO NOT assume that it does. See your Infiniti retailer to determine if this applies to your vehicle. 1/7 Camera System: Select REAR if the vehicle only has rear camera only. Select NONE/AVM ph3 if the vehicle has Around View Monitor (Check for cameras underneath side door mirrors Figure 2). Camera under outside door mirror Predictive Course Line: Does the vehicle have Around View Monitor (AVM)? Yes, select WITHOUT/WITH AVM. Figure 2 No: Select WITH (RVM WITH DAST) for vehicles equipped with Direct Adaptive Steering. Or Select WITH (RVM WITHOUT DAST) for vehicles without Direct Adaptive Steering. Sonar Type: Does the vehicle have sonar sensors on the front and rear bumpers (Figure 3)? Sonar sensor on front Yes, select FRONT&REAR. Figure 3 No, select NONE. Audio Amp Type: Does the vehicle have a Bose Audio system (Figure 4)? NOTE: You can find the BOSE emblem on the left and right sides of the dash at the windshield Yes, Select 2ch AMP. No, Select 160W AMP. Figure 4 2/7 ITB14-017a Configuration Procedure is as Follows: 1. Inspect the vehicle being worked on for its options listed above and on page 1. 2. Connect the plus VI to the vehicle. 3. Connect the AC adapter to the CONSULT PC. 4. Turn on the CONSULT PC, and then open C-III plus. 5. Press the vehicle’s power (“ignition”) switch twice without depressing the brake pedal. The meter and gauges will illuminate. CAUTION: Do Not start the vehicle. NOTE: Make sure all accessories are turned off. 6. After the plus VI is recognized, select Re/programming, Configuration. NOTE: Make sure all applications other than C-III plus are closed. Plus VI is recognized Step 6 Figure 5 3/7 ITB14-017a 7. Click on the Confirmed Instructions box and then select Next. Step 7 Figure 6 8. Select INFINITI Q50 and 2014 or Automatic Selection(VIN). If Automatic Selection(VIN) is selected, wait for the Reading VIN screen to complete (picture not shown). 9. Select Select. This works, too 2015 Step 8 Step 9 Figure 7 4/7 ITB14-017a 10. Verify the VIN in VIN or Chassis # matches that of the vehicle’s. If the correct VIN exists, select Confirm. Verify here JN1AV7AR(*)(*)M _ _ _ _ _ _ If OK, select Confirm Figure 8 11. On the next screen, select Confirm. JN1AV7AR(*)(*)M _ _ _ _ _ _ Step 11 Figure 9 5/7 ITB14-017a 12. Select MULTI AV. Wait for system call to complete. Step 12 Figure 10 13. Select Manual Configuration. Step 13 Figure 11 6/7 ITB14-017a 14. Now select the correct vehicle options for the vehicle being configured. Turn page to page 2/2 for additional configurable options. Choose vehicle options Step 15 Turn page for additional options Figure 12 15. Select Next. 16. Confirm the vehicle options for the vehicle being configured are correct. Confirm vehicle options Step 17 Figure 13 17. Select OK. 18. After the data transfer has completed select End. 19. Close the CONSULT PC. 7/7 ITB14-017a