FDM-SVC-003

Service Kit Bulletin
2.0 Left-Hand Chute Rack Platform 2 Chute
Date: August 4, 2021
Bulletin Name: FDM-SVC-003
Model: Oshkosh S-Series
Units Affected: 2.0 Front Discharge Mixers
Purpose:
This bulletin provides instruction for installing a platform on a left-hand side, 2 chute rack. Vehicles before serial
number 813916 require drilling the chute rack angle brackets for platform installation.
Notice:
• This bulletin should be read and understood in its entirety before performing this procedure.
• All procedures outlined in the bulletin must be performed by skilled service personnel. Refer to the product
service manual for descriptions of maintenance procedures.
SAFETY NOTICE
SAFETY NOTICE
Perform your company’s Lockout/Tagout
procedure. If your company does not have a
Lockout/Tagout procedure, follow OSHA
1910.147 and 1910.146 Confined Space as
appropriate.
Use appropriate Personal Protective
Equipment (PPE) as required by your
company.
Tools and Equipment Required:
Customer to supply:
•
•
•
•
Hand tools
Drill
0.410 inch drill bit
Torque wrench - foot pounds
Parts Required:
Item
Part Number
Description
Qty.
1
A000W004
BRKT, PLTF, CHUTE RK, 2 LH, SVC
1
2
A000A690
NUT, FLG, LKDT .38-16 G8 MB
4
3
A000A531
SCR, FLG, HEX .38-16X1.00 G8 MB
4
Procedure:
Lockout/Tagout
1. Place unit on a flat surface, engaged parking brake, chock truck tires, and perform your company’s Lockout/
Tagout procedure. If your company does not have a Lockout/Tagout procedure, follow OSHA 1910.147 and
1910.146 Confined Space as appropriate.
2. The vehicle’s BATTERY DISCONNECT switch is located on the left-hand side of the battery box. Use the
battery disconnect switch when performing any maintenance so the vehicle cannot accidentally be started.
a. Turn the battery disconnect switch (Figure A, Item 1) counterclockwise so the hole on the switch aligns
with the hole in the bracket (Figure A, Item 2).
1
b. Install the safety lockout device ring (Figure B, Item 1) through the holes on the battery disconnect switch
and the bracket.
c. Install a padlock (Figure B, Item 2) onto the safety lockout device ring, lock it, and put the key in your
pocket. If more than one person is working on the vehicle, each person must install his or her own padlock.
1
DA
NG
ER
Th
be is en
e
e
n
LO rgy
Un
CK sou
th auth
ED rce
OU ha
in is loc oriz
T! s
R im k/t ed
e
ma media ag m rem
rks te ay ova
:
dis re l o
ch sult f
arg
e.
1
2
2
Figure A
Figure B
Installation
NOTE
Vehicle serial number 813915 and later
continue to Step 4.
3. Drill two 0.410 inch mounting holes in each chute rack angle bracket. See Figure 1 for hole locations.
Ø 0.410 in.
26.62 in.
1.21 in.
19.489 in.
Figure 1
2
4. Install platform (A000W004) between chute rack angle brackets.
NOTE
Install platform with the larger cutouts
positioned toward front of the vehicle.
5. Secure platform to angle brackets with four 0.38-16 x 1.0 inch screws (A000A531) and four 0.38-16 inch
flanged lock nuts (A000A690), see Figure 2. Final tighten platform mounting hardware to 35 ft. lbs.
Screw
Platform
Nut
Front of Truck
Screw
Figure 2
6. Remove lockout/tagout and tire chocks.
Continuous Improvement:
The change included in this document is part of the
McNeilus Continuous Improvement Process.
McNeilus’s quality policy is providing customer satisfaction
through innovative products, dedicated service, and a
constant focus on continuous improvement.
3
(888) 686-7278
www.streetsmartparts.com