FDM-SVC-005

Service Kit Bulletin
Date: August 4, 2021
Bulletin Name: FDM-SVC-005
Model: Oshkosh S-Series
Units Affected: 2.0 Front Discharge Mixers
2.0 Rear Camera Mount - Convoy 1200A
Purpose:
This bulletin provides instruction for installing a rear camera mount to hold a Convoy model 1200A rear camera.
Notice:
• This bulletin should be read and understood in its entirety before performing this procedure.
• All procedures outlined in the bulletin must be performed by skilled service personnel. Refer to the product
service manual for descriptions of maintenance procedures.
SAFETY NOTICE
SAFETY NOTICE
Perform your company’s Lockout/Tagout
procedure. If your company does not have a
Lockout/Tagout procedure, follow OSHA
1910.147 and 1910.146 Confined Space as
appropriate.
Use appropriate Personal Protective
Equipment (PPE) as required by your
company.
Tools and Equipment Required:
Customer to supply:
• Hand tools
• Torque wrench - inch pounds
Parts Required:
Item
Part Number
1
A000W006
Description
BRKT, CAMERA, SVC
Qty.
1
Procedure:
Lockout/Tagout
1. Place unit on a flat surface, engaged parking brake, chock truck tires, and perform your company’s Lockout/
Tagout procedure. If your company does not have a Lockout/Tagout procedure, follow OSHA 1910.147 and
1910.146 Confined Space as appropriate.
2. The vehicle’s BATTERY DISCONNECT switch is located on the left-hand side of the battery box. Use the
battery disconnect switch when performing any maintenance so the vehicle cannot accidentally be started.
a. Turn the battery disconnect switch (Figure A, Item 1) counterclockwise so the hole on the switch aligns
with the hole in the bracket (Figure A, Item 2).
b. Install the safety lockout device ring (Figure B, Item 1) through the holes on the battery disconnect switch
and the bracket.
1
c. Install a padlock (Figure B, Item 2) onto the safety lockout device ring, lock it, and put the key in your
pocket. If more than one person is working on the vehicle, each person must install his or her own padlock.
1
DA
NG
ER
Th
be is en
e
e
n
LO rgy
Un
CK sou
th auth
ED rce
OU ha
in is loc oriz
T! s
R im k/t ed
e
ma media ag m rem
rks te ay ova
:
dis re l o
ch sult f
arg
e.
1
2
2
Figure A
Figure B
Installation
3. Disconnect the camera harness connector from the hood hatch harness.
4. Loosen and remove the screws, flat washers and lock nuts securing the camera and bracket to the hood
hatch, see Figure 1. Remove the camera and bracket from the hood hatch, the camera and bracket will not be
reused.
Lock Nuts
Flat Washers
Screws
Figure 1
5. Secure a Convoy Model 1200A camera to mounting bracket (A000W006) with four hex screws with flat and
lock washers supplied with the Convoy Model 1200A camera, see Figure 2.
Camera
Mounting Bracket
(A000W006)
Flat Washer
Lock Washer
Hex Screw
Figure 2
2
6. Mount the camera and bracket to the hood hatch with screws, flat washers and lock nuts removed in Step 4,
see Figure 3. Final tighten mounting hardware to 65 in. lbs.
Lock Nuts
Flat Washers
Screws
Figure 3
7. Connect camera harness connector to hatch harness connector.
8. Remove lockout/tagout and tire chocks.
Continuous Improvement:
The change included in this document is part of the
McNeilus Continuous Improvement Process.
McNeilus’s quality policy is providing customer satisfaction
through innovative products, dedicated service, and a
constant focus on continuous improvement.
3
(888) 686-7278
www.streetsmartparts.com