21-BE-013HG
Service Bulletin Details
Public Details for: 21-BE-013HG
This bulletin describes the procedure to variant code the genesis sedan (dh) navigation system. A black/blank screen or black and white image may be displayed from the rear view camera after the navigation unit is replaced without performin
Models from 2018
2018 GENESIS G80 |
Models from 2017
2017 GENESIS G80 |
2017 HYUNDAI GENESIS |
GROUP NUMBER BODY ELECTRICAL DATE Technical Service Bulletin SUBJECT: 21-BE-013HG MODEL(S) SEPTEMBER, 2021 GENESIS (DH) 2017MY – 2018MY GENESIS SEDAN STANDARD NAVIGATION (NON-DIS) VARIANT CODING IMPORTANT Use this information bulletin to variant code the standard navigation (non-DIS) system after replacement. Description: This bulletin describes the procedure to variant code the Genesis Sedan (DH) navigation system. A black/blank screen or black and white image may be displayed from the rear view camera after the navigation unit is replaced without performing this variant coding procedure. non-DIS (No Jog Dial) SYMPTOM(S) Black or Blank Screen Black and White Image Applicable Vehicles: All 2017 ~ 2018MY Genesis Sedan (DH) vehicles equipped with the standard (non-DIS) navigation system. Warranty Information: Normal warranty applies Circulate To: General Manager, Service Manager, Parts Manager, Warranty Manager, Service Advisors, Technicians, Body Shop Manager, Fleet Repair SUBJECT: 2017MY – 2018MY GENESIS SEDAN STANDARD NAVIGATION (NON-DIS) VARIANT CODING Tool Information: Part Name • GDS-Mobile Complete Kit • GDS-Mobile Lit Kit (includes VCI II Module) Part Number Image Remark • Tablet with GDS software • Scan tool needed to interface with vehicle • GDSM-CPKITH GDSM-LTKITH NOTE 1: AVM and GDS Mobile Kits have been sent to each dealership. Additional kits can be purchased through Bosch (1-866-539-4248). Service Procedure: 1. Press the START STOP BUTTON (A) to turn “ACC” ON. A 2 Plug the VCI II Module into the vehicle’s DLC port located in the lower left kick panel area (B). B TSB #: 21-BE-013HG Page 2 of 7 SUBJECT: SUBJECT: 2017MY – 2018MY GENESIS SEDAN STANDARD NAVIGATION (NON-DIS) VARIANT CODING 3. Select the S/W Management button (G). G 4. In the S/W management page, select Audio Video Navigation (Non DIS) (H), then select Variant Coding (I). H I TSB #: 21-BE-013HG Page 3 of 7 SUBJECT: SUBJECT: 5. 2017MY – 2018MY GENESIS SEDAN STANDARD NAVIGATION (NON-DIS) VARIANT CODING Upon selection of Variant Coding you will be prompted with a warning not to touch any of the system buttons as interruption could damage the ECU, tap “OK” continue (J). J GDS-M will then display a set of preconditions which have been met in step 1. Select “OK” to continue (K). K TSB #: 21-BE-013HG Page 4 of 7 SUBJECT: SUBJECT: 2017MY – 2018MY GENESIS SEDAN STANDARD NAVIGATION (NON-DIS) VARIANT CODING 6. Select “Skip” (L) to change variant coding options manually. Then select “OK” (M) to continue with the procedure. L M TSB #: 21-BE-013HG Page 5 of 7 SUBJECT: SUBJECT: 2017MY – 2018MY GENESIS SEDAN STANDARD NAVIGATION (NON-DIS) VARIANT CODING 7. Proceed with the Variant Coding procedure: • Select the items which you would like to change. The Applied Values should be as follows: Items VEHICLE VARIANT COUNTRY VARIANT NAVIGATION MODEM MOST AMP REAR SEAT ENTERTAINMENT RADIO REGION CODE STEERING WHEEL LIMOUSINE AMP VARIANT PARKING ASSIST ADVANCED CLUSTER HUD REAR SEAT USB REAR CONTROLLER CDC REAR MIC DVD REGION CODE DVD MENU LANGUAGE • Applied Value DH NORTH AMERICA ENABLE ENABLE DISABLE DISABLE 10k/200k LHD SEDAN ACTUNE PGS DISABLE DISABLE DISABLE DISABLE DISABLE DISABLE WORLDWIDE 00 Scroll down to Parking Assist, then select PGS (N). Then, select “OK” (O) to save the changes. N O TSB #: 21-BE-013HG Page 6 of 7 SUBJECT: SUBJECT: 2017MY – 2018MY GENESIS SEDAN STANDARD NAVIGATION (NON-DIS) VARIANT CODING 8. Once the changes have been submitted you will receive a notification confirming the save completed. Select “OK” (P). P 9. Upon Completion of the procedure: • Disconnect the VCI module from the vehicle. • Shut the vehicle off • Remove keys • Lock all the doors (ARM the vehicle) Wait 3-5 minutes before proceeding. 10. Confirm the rear view camera operation. Depress the brake pedal and press the START STOP BUTTON (Q) to start the vehicle. Depress the brake pedal then put the gearshift lever to Reverse. Confirm that the rear view image appears on the display. Q NOTICE Repeat steps 1-10 if the condition is not resolved. TSB #: 21-BE-013HG Page 7 of 7 SUBJECT: