V0113372012810

Technical Bulletin
Model(s)
Year(s)
Passat, Passat
Wagon
2007-2008
Jetta, Jetta
Wagon
2007-2008
Eng. Code(s)
Trans. Code(s)
VIN Range From
VIN Range To
6 Spd Auto
All
All
6 Spd Auto
All
All
2.0L
(BPY)
2.5L
(CBTA, CBUA)
Condition
01 13 37 November 20, 2013 2012810 Supersedes T. B. V011336 dated November 13, 2013 to update applicable
model table.
Update Programming, ECM, TCM Software Update and Valve Body Replacement for Harsh Up - Down
Shift from Transmission when Cold
Customer may experience harsh up shift in gears 1-2 and 2-3, or harsh down shift in gears 3-2 and 2-1. The
symptom is most noticeable at transmission temperatures below 60°C (140°F).
No DTCs are stored in the TCM or the ECM for this complaint.
Comfort concern only.
Technical Background
For harsh 1-2-3 up / downshifts when cold:
Internal transmission pressure difference on solenoid valve -N283- during shifting.
Updated ECM and TCM software and updated transmission valve body addresses:
• Harsh Up/Down Shift 1-2-3, 3-2-1
Production Solution
Updated transmission valve body, ECM and TCM software.
Page 1 of 6 plus attachment
© 2013 Volkswagen Group of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other
intellectual property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice.
No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or
otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher.
Technical Bulletin
Service
• Check the ECM and TCM software level using the VAS 5051/5052.
Tip:
If the update programming button does not appear, the latest version has already been installed.
Note:
If software level is equal to or above updated software level noted in Updated ECM or TCM Software table, DO
NOT continue with this technical bulletin, contact technical assistance by selecting the "Technical Assistance"
tab in ElsaWeb and follow the instructions to obtain a 6 digit pin.
If ECM or TCM software level is below updated software level noted in Updated ECM and/or Transmission Control
Module Software table:
• Install updated transmission valve body Part No. 09G325039* (* = install latest suffix part number available for
the model), See Repair Manual Group 38 AUTOMATIC TRANSMISSION, 6spd. Automatic Transmission.
• Update ECM and TCM program following the procedure below.
Update Programming Procedure
Tip:
To Update-Programming using SVM, review and follow instructions in Technical Bulletin Instance 2014603
“Software Version Management”.
The SVM Process must be completed in its entirety so the database receives the update confirmation response. A
warranty claim may not be reimbursed if there is no confirmation response to support the claim.
Note:
Prior to launching VAS-PC application and starting control module update process, confirm tester screen
saver and power settings in accordance with Special Tools and Equipment - Service Information Circular
# VSE-08-18. Failure to do so may result in the tester entering power save mode during data transfer, and
subsequent control module failure.
When using a VAS 6150/5051B or VAS 5052A tester in conjunction with a VAS 5054A wireless transmitter head
for a flash procedure, please connect a USB cable between the transmitter head and the tester. Failure to do so
may lead to errors during the flash procedure.
Page 2 of 6 plus attachment
© 2013 Volkswagen Group of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other
intellectual property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice.
No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or
otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher.
Technical Bulletin
• Update the Engine Control Module using the SVM action code as listed in the table below:
Year
Model
Engine
Old ECM
Part No.
Old
Software
Version
New ECM
Part No.
New
Software
Version (or
higher)
SVM Unit
Code
2007
Passat,
Passat
Wagon
2.0L (BPY)
3C0907115P
XP10
3C0907115S
0020
320A
3C0907115S
0020
320A
0010
0020
0030
2008
Passat,
Passat
Wagon
2.0L (BPY)
3C0907115S
XP10
0010
• Update the Transmission Control Module using the SVM action code as listed in the tables below:
Year
Model
2007
Passat,
Passat
Wagon
Engine
Old TCM Part
No.
2.0L (BPY) 09G927750FP
Old
Software
Version
New TCM
Part No.
New
Software
Version (or
higher)
SVM Unit
Code
0890
09G997750C
1616
320A
09G997750C
1617
320A
0931
1199
2008
Passat,
Passat
Wagon
2.0L (BPY) 09G927750HJ
1025
1068
Page 3 of 6 plus attachment
© 2013 Volkswagen Group of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other
intellectual property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice.
No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or
otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher.
Technical Bulletin
Year
Model
Engine
Old TCM Part
No.
Old
Software
Version
New TCM
Part No.
New
Software
Version (or
higher)
SVM Unit
Code
2007
Jetta
2.5L
09G927750FL
0883
09G997750D
1649
320A
0913
0920
1202
2007
Jetta
2.5L
09G997750D
1614
09G997750D
1649
320A
2008
Jetta, Jetta
Wagon
2.5L
09G927750HE
0986
09G997750E
1615
320A
1018
1054
1090
The procedure can be found in GFF under Functions/ Component Selection, Software Version Management,
Adapting Software.
WARNING:
Radiator Fan(s) may cycle ON high speed during the Update Process! There is a risk that personal injury may
result if contact is made with spinning fan blades.
Keep hands and all objects away from Radiator Fan(s) during Update Process!
Tip:
The SVM Process must be completed in its entirety so the database receives the update confirmation response. A
warranty claim may not be reimbursed if there is no confirmation response to support the claim or action is carried
out that is not explicitly stated in the Technical Bulletin.
Ensure attached ECM/TCM Tuning Form has been completed and signed by customer as required in SVM
Technical Bulletin Instance 2014603.
Page 4 of 6 plus attachment
© 2013 Volkswagen Group of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other
intellectual property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice.
No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or
otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher.
Technical Bulletin
Warranty
To determine if this procedure is covered under Warranty, always refer to the Warranty Policies and
1)
Procedures Manual
Model(s)
Year(s)
Passat, Passat
Wagon
2007-2008
Jetta, Jetta
Wagon
2007-2008
Eng. Code(s)
Trans. Code(s)
VIN Range
From
VIN Range To
6 Spd Auto
All
All
6 Spd Auto
All
All
2.0L
(BPY)
2.5L
(CBTA, CBUA)
SAGA Coding
Claim Type:
Use applicable Claim Type
Damage
Service Number:
HST
Damage Location (Depends on
Service No.)
--
Use applicable when indicated in
ElsaWeb (L/R)
Code
3877
Parts Manufacturer
0010
Passat, Passat Wagon, Jetta, Jetta
Wagon
Labor Operation : Charge Battery
3)
27068950 = 10 TU
3)
37302599 = 30 TU
Labor Operation : Valve Body Replacement
3)
38771900 = 220 TU
Causal Part:
09G325039*
Labor Operation : Verify Software Level and
Update Programming
1)
Diagnostic Time
AW5
2)
4)
GFF Time expenditure
01500000 = 00 TU max.
NO
Road Test
01210002 = 10 TU
YES
01210004 = 10 TU
Technical Diagnosis
01320000 = 00 TU max.
NO
Page 5 of 6 plus attachment
© 2013 Volkswagen Group of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other
intellectual property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice.
No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or
otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher.
Technical Bulletin
Claim Comment: Input “As per Technical Bulletin 2012810” in comment section of Warranty Claim.
1)
Vehicle may be outside any Warranty in which case this Technical Bulletin is informational only
2)
Code per warranty vendor code policy.
3)
Labor Time Units (TUs) are subject to change with ELSA updates.
4)
Documentation required per Warranty Policy Procedures Manual.
Required Parts and Tools
Description
Part No:
Quantity
Valve Body
09G325039*
1
Tool Description
Tool No:
Midtronics Battery Tester/Charger
InCharge 940 (INC-940)
VAS Diagnostic Tool
VAS 5051B, VAS 5052A, VAS 6150/X & VAS 6160/X
with:
ODIS Service 2.0.0 or higher with current online
updates
Additional Information
All part and service references provided in this Technical Bulletin are subject to change and/or removal.
Always check with your Parts Dept. and Repair Manuals for the latest information.
Page 6 of 6 plus attachment
© 2013 Volkswagen Group of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other
intellectual property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice.
No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or
otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher.
OWNER INFORMATION ABOUT CONTROL MODULE TUNING*
ACKNOWLEDGEMENT AND AUTHORIZATION FOR
REPROGRAMMING (REFLASHING) OF CONTROL MODULE(S)
*) “TUNING” is described as the addition of or modification of any component which causes a
Volkswagen vehicle to perform outside the normal parameters and specifications approved by
Volkswagen Group of America / Volkswagen Group Canada.
Date:
Dealer Number:
Vehicle Identification Number:
Repair Order Number:
Dealer stamp
I
, owner or driver of the above identified Volkswagen, confirm:
- “Tuning” as described above (especially power increasing modifications) has NOT been
performed on my vehicle.
- “Tuning” as described above has been performed on my vehicle and the following components
were modified or installed:
TUNING was performed by (Please provide Company name and telephone number, if you wish us
to contact them):
I understand that if my Control Module is determined to have been tuned, any damage caused by
the tuning of the Control Module (including adverse emissions consequences) will not be covered
by VWGoA / VGC warranties.
I am permitting an authorized Volkswagen Dealer to reflash (update) my Control Module, and by
doing so, I understand that this process will automatically overwrite (destroy) and permanently
delete any tuning program that was previously installed on the Control Module of my Volkswagen
vehicle.
By signing below, I fully acknowledge and understand that the tuning program will not be restored
and VWGoA / VGC, will not be liable in any way for the loss of tuning data.
Signature of Customer
E 2013 Volkswagen Group of America Inc. All rights reserved. Information contained in this document is based on the latest information available at the time of printi ng and is subject to the copyright and other intellectual
property rights of VGoA / VGCA Inc., its affiliated companies and its licensors. All rights are reserved to ma ke changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitte d in any
form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or rep osted to other sites, without the prior expressed written permission of the publisher .