NTB22-027

Classification:
Reference:
AN22-006
Date:
NTB22-027
April 12, 2022
B2E01-96 (INTERNAL BATTERY) DTC
STORED AS CURRENT IN IVC
APPLIED VEHICLES:
2021-2022 Armada (Y62) – All
2021-2022 Rogue (T33) – SV, SL, PLT
2022 Pathfinder (R53) – SV, SL, PLT
2021-2022 Sentra (B18) – SR w/premium
2021-2022 Kicks (P15) – SR w/premium
2020-2022 Titan (A61) – SV, SL, PRO-4X, PLT
2021-2022 Maxima (A36) – All
2022 Frontier (D41) – Pro-4X/X
SERVICE INFORMATION
CONSULT has been updated to allow DTC B2E01-96 (Internal battery) to be cleared in the
Telematics Control Unit (TCU).
If DTC B2E01-96 is Current/Active in the TCU, and No additional Current/Active DTCs are
present in the TCU, perform the SERVICE PROCEURE starting on page 2.
Nissan Bulletins are intended for use by qualified technicians, not 'do-it-yourselfers'. Qualified technicians are
properly trained individuals who have the equipment, tools, safety instruction, and know-how to do a job
properly and safely. NOTE: If you believe that a described condition may apply to a particular vehicle, DO
NOT assume that it does. See your Nissan dealer to determine if this applies to your vehicle.
1/8
SERVICE PROCEDURE
IMPORTANT: Before starting, make sure:

ASIST on the CONSULT PC has been synchronized (updated) to the current date.

All CONSULT-III software updates (if any) have been installed.

Connect a battery maintainer or smart charger set to reflash mode or a similar
setting. If the vehicle battery voltage drops below 12.0V or rises above 15.5V
during reprogramming, the TCU may be damaged.

Be sure to turn OFF all vehicle electrical loads.
If a vehicle electrical load remains ON, the TCU may be damaged.

Be sure to connect the AC Adapter.
If the CONSULT PC battery voltage drops during reprogramming, the process
will be interrupted and the TCU may be damaged.

Turn OFF all external Bluetooth® devices (e.g., cell phones, printers, etc.)
within range of the CONSULT PC and the VI. If Bluetooth® signal waves are
within range of the CONSULT PC or VI during reprogramming, reprogramming
may be interrupted and the TCU may be damaged.
1.
Connect a battery maintainer/smart charger to the vehicle.
2.
Turn the ignition ON.
3.
Connect the VI to the vehicle.
4.
Start CONSULT-III.
5.
Wait for the VI to be recognized.

The serial number will display when the VI is recognized (Figure 1 on
page 3).
2/8
NTB22-027
6.
Select Diagnosis (All Systems).
The VI is
recognized
Figure 1
7.
Verify the correct VIN or Chassis # is populated (Figure 2).
8.
Select Confirm.
XXXXXXXXXXXXXXXXX
XXXXXXXX
XXXXXXXX
Figure 2
3/8
NTB22-027
9.
Confirm that DTC B2E01-96 for Internal battery is “CRNT” in the IVC.

If only DTC B2E01-96 is present, select IVC (Figure 3) and then proceed to
step 10.

If additional DTCs, other than B2E01-96, are present in the IVC, refer to the ESM
for further diagnostic information and repair first, and then proceed to step 10.
NOTE: Diagnostic and repair of DTCs other than B2E01-96 are not covered by
this bulletin.
Figure 3
10.
Select CGW Information.

If there is a red indicator next to CGW Information (Figure 4), select CGW Open,
follow the NNAnet instructions (Figure 5), and then proceed to step 11 on page 5.

If there is a green indicator next to CGW Information, proceed to step 11 on
page 5.
Figure 4
Figure 5
4/8
NTB22-027
11.
Select Work support.
Figure 6
12.
Select TCU Backup Battery Reset, and the select Start.
Figure 7
5/8
NTB22-027
13.
Verify that the Current status indicates “Waiting”, and then select Start.
Figure 8
14.
When the Current status has changed to “Completed” select End, and then proceed
to step 15 on page 7.
Figure 9
6/8
NTB22-027
15.
Select Self Diagnostic Result and confirm that DTC B2E01-96 Internal battery is
“PAST”, and then select ERASE.

If B2E01-96 Internal battery will not change to “PAST”, refer to the ESM for
further diagnostic information.
Figure 10
16.
Select Diagnosis (All Systems), where shown in Figure 11.
17.
In Diagnosis (All Systems), confirm that B2E01-96 Internal battery IVC has not
returned, and then select Home.

If B2E01-96 Internal battery returns as “CRNT” or will not ERASE, refer to the
ESM for further diagnostic information.
Figure 11
7/8
NTB22-027
CLAIMS INFORMATION
Submit a Primary Part (PP) type line claim using the following claims coding:
(1)
DESCRIPTION
PFP
OP CODE
SYM
DIA
FRT
Reset TCU Backup Battery
(1)
RXA9AA
ZE
32
0.4
Reference the electronic parts catalog and use the Telematics Control Unit (28275*****) as the Primary Failed Part (PFP).
AMENDMENT HISTORY
PUBLISHED DATE REFERENCE
April 12, 2022
NTB22-027
DESCRIPTION
Original bulletin published
8/8
NTB22-027