SA-017-22c
Service Bulletin Details
Public Details for: SA-017-22c
Some customers may complain about any of the following: * infotainment center display does not provide the authorization code during the mymazda app connected vehicle enrollment. * remote function(s) inoperative. - engine start / stop
- 2023 - 2022 - 2021 - 2020 - 2019 -
Models from 2023
2023 MAZDA CX-30 |
2023 MAZDA CX-5 |
2023 MAZDA CX-50 |
2023 MAZDA CX-9 |
2023 MAZDA MAZDA3 |
Models from 2022
2022 MAZDA CX-30 |
2022 MAZDA CX-5 |
2022 MAZDA CX-9 |
2022 MAZDA MAZDA3 |
2022 MAZDA MX-30 PHEV |
Models from 2020
2020 MAZDA CX-30 |
2020 MAZDA MAZDA3 |
Models from 2019
2019 MAZDA MAZDA3 |
BULLETIN NOTES This service alert supersedes the previously issued service alert listed below. The changes are noted in Red text. Previous TSBs: Date(s) Issued: SA-017/22 08/25/22, 05/06/22, 04/04/22 SA-013/21 12/22/21, 10/13/21, 09/14/21, 05/11/21, 04/27/21, 03/15/21, 02/22/21, 02/08/21 and 02/02/2021 SA-031/20 12/09/20,11/30/20, 11/06/20, 10/28/20, 06/16/20, 06/05/20, 06/01/20, 05/18/20, 04/14/2020, 04/02/20, 03/11/20 and 02/27/20 APPLICABLE MODEL(S)/VINS: 2019-2023 Mazda3 2020-2023 CX-30 2021-2023 CX-5 2021-2023 CX-9 2022 MX-30 2023 CX-50 DESCRIPTION Some customers may complain about any of the following: • Infotainment Center Display does not provide the Authorization Code during the MyMazda App Connected Vehicle enrollment. • Remote function(s) inoperative. Engine Start / Stop Door Lock / Unlock Lights ON / OFF • MAZDA CONNECT connected vehicle reception strength icon shows "X" or "\". ○ ○ ○ Page 1 of 19 10/20/2022 08:52 AM cciz Confirm the customer's phone and vehicle have good to strong reception during the concern as shown in the table below. • If the reception is weak, move the vehicle to a location where the reception is good to strong as shown in the table, then try to get the Authorization Code and/or operate the remote functions before proceeding to the Repair Procedure if there is still an issue. • If the reception is good to strong, proceed to the Repair Procedure. Indication Explanation Mazda3, CX-30, CX-50, MX-30 Radio waves are not being received. Move to a location with good reception. Weak reception. Good Receptioin Strong reception. Currently conducting an operation check of the communication unit. If this condition continues, consult an Authorized Mazda Dealer. Currently conducting an operation check of the onboard communication unit. NOTE: Communication is not possible during this display. CX-5, CX-50, CX-9, MX-30 Mazda3, CX-30 built July 1, 2021 and later The communication function is temporarily disabled due to infotainment system setting. Mazda3, CX-30, CX-50, MX-30 • Connected Service contract has ended (Subscription expired) Page 2 of 19 10/20/2022 08:52 AM cciz CX-5, CX-9 • TCU has not been initialized, go to SA-004/21 Vehicles built before July 1, 2021 Customer deactivated Connected Services (Opt-Out) Vehicles built after July 1, 2021 • eMDCS Warranty Vehicle Inquiry will show Campaign CSP04 Status Open Connected Services disabled (box unchecked) CX-5, CX-50, CX-9, MX-30 Mazda3, CX-30 built July 1, 2021 and later Connected Services Disabled message appears at engine start up Enable Connected Services (box checked) to prevent message appearing at engine start up. Note: If customer Opted-Out ( CSP04), advise customer to keep Connected Services box checked. The vehicle will not transmit data. Connected Vehicle Maintenance Mode Connected Vehicle Maintenance Mode enabled. Go to MGSS SERVICE CAUTIONS FOR VEHICLES WITH TELEMATICS COMMUNICATION SYSTEM to disable Maintenance Mode. Page 3 of 19 10/20/2022 08:52 AM cciz Remote Engine Start Will Not Function under the following conditions Item Condition 1 Vehicle battery voltage low 2 Automatic Transmission shift position except "P" 3 Vehicles equipped with manual transmission 4 Vehicle speed above 3 mi/h (5 km/h) 5 Brake pedal switch malfunction 6 Engine has been running by remote engine start function 7 Engine started by remote engine start more than 2 consecutive times while the vehicle is not driven. The vehicle must be driven 1-mile or 24-hours must pass from the last successful Remote Engine Start for the use count to reset. 2021 Mazda3, 2021 CX-30, CX-50, MX-30: Vehicle's electrical control area network (CAN) is in "Sleep Mode" 8 or 9 A registered key is detected in the vehicle 10 Brake pedal switch detects brake application Low fuel warning 11 12 Engine starts, then turns OFF due to abnormal high engine rpm detected. (Engine rotation over 3000 rpm continued for more than 0.2[s]) 13 No engine rpm detected after sending engine start request. (Engine rotation 0 rpm continued for more than 0.2[s]) 14 When the CAN data signal for engine shut off is present (e.g.: door ajar signal) 15 After 10 second maximum cranking time 16 Burglar alarm status is "Alarm" and "Alarm stand by" (CAUTION - DO NOT enable, see TheftDeterrent System section in SA-012/20) 17 Room fuse blown/missing 18 Connected Vehicle Maintenance Mode enabled (Restricted Transmitting Mode in MDARS) Page 4 of 19 10/20/2022 08:52 AM cciz 19 Vehicle is parked (stored) for approximately 1 week or longer or in deep sleep mode. Drive the vehicle for a few miles to recover. DTC Stored 20 21 Aftermarket Remote Engine Start accessory installed. Mazda Remote Engine Start (BCKA-V7-620) accessory installed (No MyMazda app remote engine start function). 22 Mazda Remote Engine Start (RES) Removal a. Remove the Mazda Remote Engine Start (RES) accessory module. b. Deactivate and activate Advanced Key(s). Refer to MGSS IMMOBILIZER SYSTEMRELATED PARTS PROGRAMMING [(US)] 23 First remote control attempt fails, second attempt works fine. Go to TSB 16-002/20. 24 CSP04 Status Open Remote Engine Start Function Will turn engine OFF under the following conditions Item Condition 1 Vehicle door(s) opened 2 Vehicle trunk opened 3 Vehicle hood opened 4 Ignition switch push button "ON" detected 5 Remote engine STOP request 6 Brake pedal switch detects brake application 7 DTC Stored 8 Engine will stop running automatically after 15 minutes for safety, security and emissions. Page 5 of 19 10/20/2022 08:52 AM cciz REPAIR PROCEDURE CAUTION: • Before continuing, confirm that the TCU is at the latest software level. Go to Telematics Communication Unit (TCU) Updates • DO NOT swap TCU with another vehicle as the TCU is VIN locked after activation. A TCU swap with another vehicle will disable Connected Services on both vehicles. NOTE: Vehicles stored for long periods may loose GPS clock sychronization. If the vehicle is stored for a long period, test drive the vehicle to give the GPS clock time to sychronize before enrolling or testing connected vehicle functions. Index 1. Remote function(s) inoperative 2. Unable to enroll into connected services 3. Connected vehicle reception strength icon shows "X" or "\" 4. MyMazda App displays incorrect tire pressures (Except CX-5 and CX-9) 5. Unable to activate Connected Services (2019 Mazda3) 6. Software Update Error (2020 Mazda3) 7. Functions inoperative (2021-> CX-30, CX-50, Mazda3 and MX-30) 8. First remote control attempt fails, second attempt works fine 9. Engine turns off when opening door 10. Low Tire pressure will not clear after correcting tire pressue 11. Educational Videos 12. Resources Page 6 of 19 10/20/2022 08:52 AM cciz Connected Vehicle Troubleshooting Symptom Cause Action Push Notification OS Lock Screen Tap the push notification Go to the MyMazda App to view the reason for remote function failure. Home Tap the alert card Inbox Detail Tap "check vehicle status" Go to the MyMazda App INBOX -> ACTIVITY HISTORY -> to view reason for remote function failure. Remote function(s) inoperative. 1 • Engine Start / Stop • Door Lock / Unlock • Lights ON / OFF Activity History 1. Use MDARS to ID the vehicle and check for DTC's stored. Are DTC(s) stored? • Yes - Go to MGSS and perform normal DTC diagnostics. • No - Go to next step. Troubleshooting 2. If applicable, confirm SSPC7 or DRW41 is closed. Go needed to eMDCS Vehicle Inquiry. 3. Confirm TCU software version is at the following using TCU Software Version Check • Mazda3 - 10006 or later • CX-30 - 10006 or later Page 7 of 19 10/20/2022 08:52 AM cciz • CX-5 - 10023 or later • CX-9 - 10023 or later • MX-30: 10019 or later • CX-50: N/A 4. Disconnect battery for 30 seconds and then reconnect (KAM reset). NOTE: Test drive vehicle after battery disconnect to allow the GPS clock to sychronize before retrying Authorization Code. 5. Perform one of the following: • Customer: Un-enroll Connected Services, then re-enroll into Connected Services as a new primary user. • Dealer: Perform customer take-over enrollment for test confirmation, then at customer pick-up, inform customer to re-enroll into Connected Services as a new primary user. 6. Contact Hotline for additional technical support if needed. Only a single remote request Customer needs to wait 60 seconds for the initial can be made request cycle to be completed to make the second per 60-second request. period Remote Transmitter Key(s) in the vehicle 1. Aftermarket Remote Engine Start accessory installed. 2. Mazda Remote Engine Start (BCKAV7-620) accessory installed. TCU in “deep Do not leave keys in vehicle. 1. Remove the aftermarket accessory. 2. The customer can use either the Mazda Remote Engine Start accessory or the MyMazda app function. Cannot use both. Mazda Remote Engine Start (RES) Removal a. Remove the Mazda Remote Engine Start (RES) accessory module. b. Deactivate and activate Advanced Key(s). Refer to MGSS IMMOBILIZER SYSTEM-RELATED PARTS PROGRAMMING [(US)]. Advise customer to drive the vehicle as normal (at least Page 8 of 19 10/20/2022 08:52 AM cciz sleep” mode due to vehicle being parked for a long period. several miles) and the Connected Services should start working again. Low fuel Advise customer that Remote Engine Start may start vehicle temporarily, but vehicle will turn off automatically when the fuel level is low to conserve the remaining fuel. Vehicle is equipped with Manual Transmission Advise customer that vehicles with a manual transmission do not have the Remote Engine Start/ Stop function capability. Engine started with key transmitter instead of MyMazda App. Advise customer they will see an error message when attempting to make a Remote Engine Off request if they initially turned on vehicle with a physical key (instead of through their MyMazda app). Customer deactivate Connected Services (OptOut)) Go to eMDCS Vehicle Inquiry. Does eMDCS show CSP04 status closed? • Yes - Customer opt-out. No action needed. • No - CSP04 is not shown. Go to next Action below. 1. Use MDARS to ID the vehicle and check for DTC's stored. Are DTC(s) stored? • Yes - Go to MGSS and perform normal DTC diagnostics. • No - Perform ODR Data Collection Procedure, then go to step 2. No One Time Passcode (OTP) (Vehicle infotainment center display 2 does not provide the Authorization Code during the MyMazda App enrollment) 2. Confirm TCU software version is at the following using TCU Software Version Check. Troubleshooting needed • • • • • • Mazda3 - 10006 or later CX-30 - 10006 or later CX-5 - 10023 or later CX-9 - 10023 or later MX-30: 10019 or later CX-50: N/A 3. Retrieve MAZDA CONNECT CMU log data. Go to MGSS -> Infotainment -> MAZDA CONNECT CMU Data Retrieval 4. Perform "Activating Remote Control by Smart Phone" (links TCU to BCM) 5. Clear DTC(s). Page 9 of 19 10/20/2022 08:52 AM cciz NOTE: If DTC 2050:55 is stored, go to SA-003/20 to clear DTC. 6. Perform KAM reset. NOTE: Test drive vehicle after a KAM reset to allow the GPS clock to sychronize before retrying Authorization Code. 7. Contact Hotline for additional technical support if needed. 1. Go to eMDCS Vehicle Inquiry. Does eMDCS show CSP04 status closed? • Yes - Customer opt-out. No action needed. • No - CSP04 is not shown. Go to next step. 2. Check for DTCs. Are there any DTC's stored? • Yes: Go to MGSS for normal DTC diagnosis. • No: Go to next step. 3. Confirm TCU software version is at the following using TCU Software Version Check. MAZDA CONNECT connected vehicle reception strength icon shows "X" or "\". Mazda3, CX-30, CX-50, MX-30 3 • • • • • • No reception CX-5, CX-9 Mazda3 - 10006 or later CX-30 - 10006 or later CX-5 - 10023 or later CX-9 - 10023 or later MX-30: 10019 or later CX-50: N/A 4. Disconnect battery terminal for 30 seconds, then test drive the vehicle. Is the reception strength signal normal? • Yes: Repair complete. • No: Go to next step. 5. Perform TCU activation. Go to SA-004/21. Is the reception strength signal normal? • Yes: Repair complete. • No: Go to next step. 6. Compare Tel antenna No. 1 signal strength with good known vehicle near by. Go to DIAGNOSTIC ASSIST FUNCTION [CONNECTIVITY MASTER UNIT (US)] Functional Inspection / Adjustment -> Navigation System Inspection Good - Contact Hotline for technical support Page 10 of 19 10/20/2022 08:52 AM cciz No Good - Swap Tel antenna No. 1 with known good vehicle Except CX-5 and CX-9 MAZDA CONNECT and/or MyMazda App displays incorrect tire pressures after battery disconnect and/or infotainment CMU software update. 4 Incorrect calendar entry (month/day/ year) after a battery disconnect or infotainment system software update. Go to SA-002/21 2019 Mazda3 only 5 • The customer is not able to activate Connected Services via the MyMazda app after CSP06 completion. • MAZDA CONNECT connected vehicle reception strength icon is missing or shows unsubscribed after CSP06 completion. Improper telematics communication Go to CSP07 Repair instructions. unit (TCU) software. Page 11 of 19 10/20/2022 08:52 AM cciz 2020 Mazda3 only 6 • Infotainment center display does not provide the Authorization Code • Infotainment center display “Software Update Error” message Enrollment error Go to SSPC1 2021 Mazda3, CX-30, CX-50, and MX30 functions inoperative 7 • • • • • Vehicle Status Alert Remote Engine Start / Stop Remote Door Lock / Unlock Remote Hazard Lights ON / OFF Vehicle Finder (vehicle location mapping function is available) Vehicle's electrical control area network (CAN) is in "Sleep Mode" or No dealer visit is required. Sleep Mode can be reset by starting the engine and idling or driving for 5 minutes or longer. Page 12 of 19 10/20/2022 08:52 AM cciz Go to 09-010/22. First remote control attempt fails, second Improper attempt works fine. telematics 8 • Engine Start / Stop communication Go to TSB 16-002/20. • Door Lock / Unlock unit (TCU) • Lights ON / OFF software. 9 10 Engine turns off when customer opens vehicle door. • Low Tire pressure will not clear after correcting tire pressue. • Vehicle status is inaccurate. Normal Operation MyMazda App is not real time. Advise that, for customer’s safety and security, vehicle is designed to shut-off automatically when the vehicle door is opened. • Customer must go to MyMazda app’s Inbox and read/open all the messages related to the low tire pressure alert, then the “Low tire pressure” alert will clear from MyMazda app’s Health Report • Message will clear after next drive cycle. ODR Data Collection Procedure 1. ID the vehicle using MDARS --- 2. Select "Toolbox" Page 13 of 19 10/20/2022 08:52 AM cciz 3. Select Vehicle Icon 4. Expand "Collect Diagnostic Information" 5. Select Collecting diagnostic information "Run". Page 14 of 19 10/20/2022 08:52 AM cciz 6. Turn the ignition ON, then select "Next" 7. Wait for collection to complete. 8. Confirm that the ODR collection has been successful. Select “Next” to exit. Activating Remote Control by Smart Phone (links TCU to BCM) Page 15 of 19 10/20/2022 08:52 AM cciz NOTE: This procedure cannot be performed if the key transmitter power saving function is enabled. See SA-040/20. 1. Connect MDARS. 2. Use MDARS to verify if the Telematics Control Unit (TCU) is at the latest software level (Toolbox > Software Update > Run > TCU). Is the TCU at the latest software level? • Yes: Go to step 3. • No: Update TCU software, then go to step 3. 3. Select the following: a. Toolbox b. Repair icon c. MAZDA CONNECT d. Activating Remote Control by Smart Phone e. RUN. 4. Follow the on-screen instructions and wait for process to complete. NOTE: If the Activating Remote Control by Smart Phone shows "Incomplete", the possible causes are: a. The advanced key is not in the vehicle. b. The connected Vehicle Maintenance Mode is enabled. c. The Key transmitter power saving function is Page 16 of 19 10/20/2022 08:52 AM cciz enabled. d. The pacemaker radio wave interference prevention function is enabled. 5. Select Quick Check (A), then start the engine and select the DTC Clear icon (B). CAUTION: If the engine is not started, DTC P2610 is stored and cannot be erased. Page 17 of 19 10/20/2022 08:52 AM cciz TCU Software Version Check CX-5 and CX-9 CX-30, CX-50, Mazda3 and MX30 1. Press and hold the Volume knob, then press and hold the Entertainment and Favorite buttons at the same time for 3-5 seconds and the Factory/ Service Inspection screen will appear. 2. Select Service Information. 3. Select TCU Linked information. 4. Scroll down to TCU Software Version and confirm the software version is at: • • • • • • Mazda3 - 10006 or later CX-30 - 10006 or later CX-5 - 10023 or later CX-9 - 10023 or later MX-30: 10019 or later CX-50: N/A Is the TCU software version correct? • Yes: TCU Software Version Check is complete. Page 18 of 19 10/20/2022 08:52 AM cciz • No: Go to Telematics Communication Unit (TCU) Updates to update the TCU software version. Educational Videos Overview Using MyMazda App In-car Wi-Fi hotspot MyMazda remote Notifications Saftey features Resources SA-019/22 - MAZDA CONNECTED SERVICES - FREQUENTLY ASKED QUESTIONS (FAQ) Connected Services Owner's Manual MAZDA CONNECT and MAZDA CONNECTED SERVICES USER GUIDE MAZDA CONNECTED VEHICLE VIEWER (MCVV) USER GUIDE MAZDA CONNECT ESSENTIALS WBT (30076) MAZDA CONNECT & CONNECTED SERVICES FOCAL POINT (30093FOC) MAZDA CONNECTED SERVICES SMART CARDS MAZDA CONNECTED SERVICES: CUSTOMER OUTREACH Page 19 of 19 10/20/2022 08:52 AM cciz