2068557.1

Technical product information
Topic
Market
area
Brand
Rear heated arm rest feature is incorrectly displayed within the TSR
Russische Föderation (5RU),Australia E04 Bentley rest Asia and Australia (6E04),China 796 VW Import Comp. Ltd (Vico), Beijing
(6796),Germany E02 Bentley rest Europe (6E02),Japan E03 Bentley Japan (6E03),Korea, (South) E08 Bentley South Korea
(6E08),United Arab Emirates E06 Bentley Middle East and Africa (6E06),United Kingdom E01 Bentley UK (6E01),United States
E05 Bentley USA and rest America (6E05)
Bentley
Transaction
2068557/1
No.
Level
EH
Status
Approval
Release
date
New customer code
Object of complaint
Complaint type Position
body fixtures and fittings -> operation and control, seats, seatbench, armrests, 2nd row functionality
Vehicle data
Bentayga EWB
Sales types
Type MY Brand Designation Engine code Gearbox code Final drive code
ZV1* 2023 E
*
*
*
Documents
Document name
master.xml
INTERNAL
Technical product information
Rear heated arm rest feature is incorrectly displayed within the TSR
Transaction No.: 2068557/1
Customer statement / workshop findings
Rear heated arm rest feature is incorrectly displayed within the TSR
Technical background
Vehicles with PR codes 98B + 5KA do not show the heated arm rest feature within the TSR. If coded incorrectly the vehicle will not show the
feature within the TSR resulting in the feature not being operational.
Vehicles with PR codes 98B + 3NL incorrectly show the heated arm rest feature within the TSR. If coded incorrectly the vehicle will incorrectly
show the feature within the TSR resulting in the feature not being operational.
In the event the issue is as described please check Elsa Pro to confirm that SC22/36 is applicable to your particular VIN, in the event that
SC22/36 is applicable please refer to the instructions within the SC22/36
However in the event that SC22/36 is not VIN applicable and the symptoms described are evident the operative must conduct the instructions
within the Measure section to update Address 08 - Air conditioning control unit
Production change
Under investigation
Measure
General information for the reprogramming:
•
The closed-circuit voltage of the vehicle must be at least 12.5 V during the update. Connect a suitable battery charger
to the vehicle. For further information refer to the Repair manual
•
During the update switch off all unnecessary consumers (ventilation, seat heater, interior illumination etc) ensure the
main light switch is set to ‘off’
•
Because of the highest transmission stability you MUST use the diagnosis interface VAS 6154 (WiFi diagnostic tool)
ONLY in USB operation or the cable-connected VAS 5055 for the reprogramming (updating) of control units. If these
units are not available, the diagnosis interface VAS 5054 (A) can also be used in USB mode
•
Do Not under any circumstances use a Bluetooth connection to conduct the reprogramming (updating) of any control
units
1. Select and run Guided fault finding
•
Within the Special functions tab select ‘SVM – Code Input’ then select Perform test (Figure 1)
Figure 1
2. Referring to Figure 2 (Point A) enter SVM code 4V1HTDARM01
•
Select Adopt (Point B)
INTERNAL
Figure 2
3. Follow all remaining on screen prompts
•
Once complete a message will be displayed confirming that all actions have been completed successfully
•
Follow on screen prompts until program end
4. After the update programming is complete, perform a CAN sleep, carry out the following steps in the order stated below:
•
Switch off the ignition
•
Remove the diagnostic interface from the OBD port
•
Switch off and remove the battery charger from the vehicle
•
Close the bonnet and all doors then lock the vehicle
•
Wait 5 minutes so that the vehicle goes into bus silence
•
When 5 minutes has elapsed, unlock the vehicle and open the driver’s door
•
Switch on the ignition
•
Confirm gear selection is possible
5. On completion – Raise a non-technical DISS stating the following:
•
SC 22/36 was not VIN applicable although the symptoms described were evident
•
SVM code 4V1HTDARM01 was successfully applied
Warranty accounting instructions
Warranty type
110 or 910
Damage service number 87 11
Damage code
02 02
Labour
Labour operation code 01 51 00 00
Time
As per the ODIS log (Must not exceed 30 time units)
INTERNAL