SSM71974

Service Bulletin Details

Public Details for: SSM71974

Diagnosing the bms when dtc B11DB-87 is logged.


- 9999 - 2023 - 2022 - 2021 - 2020 - 2019 - 2018 - 2017 - 2016 - 2015 - 2014 - 2013 - 2012 - 2011 - 2010 - 2009 - 2008 - 2007 - 2006 - 2005 - 2004 - 2003 - 2002 - 2001 - 2000 - 1999 - 1998 - 1997 - 1982 -

Models from 9999
9999 JAGUAR XJ
Models from 2008
2008 JAGUAR XK
Models from 2007
2007 JAGUAR XK
Models from 2006
2006 JAGUAR XK
Models from 2005
2005 JAGUAR XK
Models from 2004
2004 JAGUAR XK
Models from 2003
2003 JAGUAR XK
Models from 2002
2002 JAGUAR XK
Models from 2001
2001 JAGUAR XK
Models from 2000
2000 JAGUAR XK
Models from 1999
1999 JAGUAR XK
Models from 1998
1998 JAGUAR XK
Models from 1997
1997 JAGUAR XK
Models from 1982
1982 JAGUAR XJ
TOPIx - SSM71974 - Diagnosing the BMS when DTC B11DB-87 is logged.
Reference
SSM71974
Models
XK / X150
Page 1 of 1
F-TYPE / X152
XJ / X351
XF / X250
Title
Diagnosing the BMS when DTC B11DB-87 is logged.
Category
Electrical
Last modified
09-Sep-2014 00:00:00
Symptom
203000 Basic Electrical
Content
Issue:
A significant number of BMS (Battery Monitoring System) modules have been replaced when DTC B11DB-87 is logged, when returned
to the supplier for analysis many are deemed “No Fault Found”
Cause:
Incorrect diagnosis
Action:
If a vehicle is presented with DTC B11DB-87 logged follow the diagnostic routine below before replacing the BMS module:NOTE: If DTC B11DB-87 is flagged but a "charge system fault" warning / light is not present on the cluster, then the BMS is not the
causal part.
1a. If only DTC B11DB-87 is present then go to Step 4
b. If DTC B1412-87 (Quiescent Current Control Module – missing message) is also present, check the continuity of GWM LIN_1 circuit
and rectify if required. Go to Step 2.
2. Clear DTCs and re-test the vehicle (vehicle must have the ignition on or engine running for a minimum of 20secs before the re-test).
Go to Step 3.
3a. If only B11DB-87 is still present go to Step 4.
b. If only B1412-87 is still present, investigate the QCCM.
c. If both DTCs are still present, investigate the GWM (Gate Way Module).
4a. Check BMS is seated correctly on battery post (it should slightly protrude from ring)
b. Check BMS power (thin wire from positive terminal) is securely connected to positive terminal with no wiring damage.
c. Check BMS for plug/harness disconnect and security of wires into the back of the plug.
d. Disconnect the BMS and LIN plug and visually inspect pins in both ends for damage and rectify as required.
Note: XF only, ensure that the earth cable fixing at location G4D178 is secure and torqued to 13.5Nm
5. Clear DTCs and re-test the vehicle as per Step 2.
6. If DTC B11DB-87 is still present, replace the BMS module.
http://topix.jaguar.jlrint.com/topix/service/archive/496668/index
9/10/2014


© dot.report 2024

Use of this information constitutes acceptance for use in an AS IS condition. There are NO warranties, implied or otherwise, with regard to this information or its use. Any use of this information is at the user's risk. It is the responsibility of user to evaluate the accuracy, completeness or usefulness of any information, opinion, advice or other content. EACH USER WILL BE SOLELY RESPONSIBLE FOR ANY consequences of his or her direct or indirect use of this web site. ALL WARRANTIES OF ANY KIND ARE EXPRESSLY DISCLAIMED. This site will NOT BE LIABLE FOR ANY DIRECT, INDIRECT or any other kind of loss.