22-NA-254
Service Bulletin Details
Public Details for: 22-NA-254
This technical bulletin provides repair information to correct a customer concern of unwanted traction control events.
Models from 2020
2020 CHEVROLET SILVERADO 4500HD |
2020 CHEVROLET SILVERADO 5500HD |
2020 CHEVROLET SILVERADO 6500HD |
Models from 2019
2019 CHEVROLET SILVERADO 4500HD |
2019 CHEVROLET SILVERADO 5500HD |
2019 CHEVROLET SILVERADO 6500HD |
Bulletin No.: Service Bulletin Date: 22-NA-254 February, 2023 TECHNICAL Subject: Unwanted Traction Control Events Brand: Model: Chevrolet Silverado MD 4500/5500/6500 Involved Region or Country Model Year: from to 2019 2020 VIN: from Engine: Transmission: to North America Additional Options (RPOs) Condition Some customers may comment that they are having intermittent unwanted traction control events after replacing two tires and/or uneven tire wear. The condition may occur with a straight line acceleration and/or on turns. Cause The cause of the condition may be a software concern with the Electronic Brake Control Module (EBCM). Correction Reprogram the EBCM. Service Procedure Important: Service agents must comply with all International, Federal, State, Provincial, and/or Local laws applicable to the activities it performs under this bulletin, including but not limited to handling, deploying, preparing, classifying, packaging, marking, labeling, and shipping dangerous goods. In the event of a conflict between the procedures set forth in this bulletin and the laws that apply to your dealership, you must follow those applicable laws. Caution: Before downloading the update files, be sure the computer is connected to the internet through a network cable (hardwired). DO NOT DOWNLOAD or install the files wirelessly. If there is an interruption during programming, programming failure or control module damage may occur. • Ensure the programming tool is equipped with the latest software and is securely connected to the data link connector. If there is an interruption during programming, programming failure or control module damage may occur. • Stable battery voltage is critical during programming. Any fluctuation, spiking, over voltage or loss of voltage will interrupt programming. Install a GM Authorized Programming Support Tool to maintain system voltage. Refer to www.gmdesolutions.com for further information. If not available, connect a fully Copyright 2023 General Motors LLC. All Rights Reserved. charged 12 V jumper or booster pack disconnected from the AC voltage supply. DO NOT connect a battery charger. • Follow the on-screen prompts regarding ignition power mode, but ensure that anything that drains excessive power (exterior lights, HVAC blower motor, etc) is off. • Clear DTCs after programming is complete. Clearing powertrain DTCs will set the Inspection/ Maintenance (I/M) system status indicators to NO. Important: The service technician always needs to verify that the VIN displayed in the TLC left side drop down menu and the top center window match the VIN plate of the vehicle to be programmed prior to using Service Programming System 2 (SPS2) for programming or reprogramming a module. • For the TLC application, service technicians need to always ensure that the power mode (ignition) is “ON” before reading the VIN from the vehicle’s VIN master module and that they do not select a VIN that is already in the TLC application memory from a previous vehicle. • If the VIN that shows up in the TLC top center window after correctly reading the VIN from the vehicle does not match the VIN plate of the vehicle, manually type in the VIN characters from the vehicle VIN plate into the TLC top center window and use these for programming or reprogramming the subject module with the correct vehicle VIN and software and/or calibrations. Page 2 February, 2023 Bulletin No.: 22-NA-254 • The Engine Control Module (ECM) is the master module (for VIP vehicles) that TLC reads to determine the VIN of the vehicle. If the VIN read from the vehicle by TLC does not match the VIN plate of the vehicle, the ECM also needs to be reprogrammed with the correct VIN, software and calibrations that match the vehicle’s VIN plate. • The Body Control Module (BCM) is the master module (for GEM vehicles) that TLC reads to determine the VIN of the vehicle. If the VIN read from the vehicle by TLC does not match the VIN plate of the vehicle, the BCM also needs to be reprogrammed with the correct VIN, software and calibrations that match the vehicle’s VIN plate. Caution: Be sure the VIN selected in the drop down menu (1) is the same as the vehicle connected (2) before beginning programming. 5743643 Bulletin No.: 22-NA-254 February, 2023 Page 3 Important: If the vehicle VIN DOES NOT match, the message below will be shown 5877000 5644477 Important: Techline Connect screens shown above. Important: If the same calibration/software warning is noted on the TLC Summary screen, select OK and follow screen instructions. After a successful programming event, the WCC is located in the Service Programming System dialogue box of the SPS Summary screen. No further action is required. Refer to the Warranty section of the bulletin. 1. Reprogram the Electronic Brake Control Module. Refer to K17 Electronic Brake Control Module: Programming and Setup in the Service Manual. Page 4 February, 2023 Bulletin No.: 22-NA-254 5644478 Note: The screenshot above is an example of module programming and may not be indicative of the specific module that is being programmed. Module selection and VIN information have been blacked out. Important: To avoid warranty transaction rejections, you MUST record the warranty claim code provided on the Warranty Claim Code (WCC) screen shown above on the job card. Refer to callout 1 above for the location of the WCC on the screen. 2. Record SPS Warranty Claim Code on job card for warranty transaction submission. Bulletin No.: 22-NA-254 February, 2023 Page 5 Warranty Information For vehicles repaired under the Bumper-to-Bumper coverage (Canada Base Warranty coverage), use the following labor operation. Reference the Applicable Warranties section of Investigate Vehicle History (IVH) for coverage information. Labor Operation Description Labor Time *2889128 Reprogram the Electronic Brake Control Module (EBCM) for Unwanted Traction Control Events 0.3 hr *This is a unique Labor Operation for Bulletin use only. Important: **To avoid warranty transaction rejections, carefully read and follow the instructions below: 6125814 • • The Warranty Claim Code must be accurately entered in the “Warranty Claim Code” field of the transaction. When more than one Warranty Claim Code is generated for a programming event, it is required to document all Warranty Claim Codes in the “Correction” field on the job card. Dealers must also enter one of the codes in the “Warranty Claim Code” field of the transaction, otherwise the transaction will reject. It is best practice to enter the FINAL code provided by SPS2. Page 6 February, 2023 Bulletin No.: 22-NA-254 Warranty Claim Code Information Retrieval 6125774 If the Warranty Claim Code was not recorded on the Job Card, the code can be retrieved in the SPS2 system as follows: 1. Open TLC on the computer used to program the vehicle. 2. Select and start SPS2. 3. Select Settings (1). 4. Select the Warranty Claim Code tab (2). The VIN, Warranty Claim Code and Date/Time will be listed on a roster of recent programming events. If the code is retrievable, dealers should resubmit the transaction making sure to include the code in the SPS Warranty Claim Code field. Version 1 Modified Released January 27, 2023 GM bulletins are intended for use by professional technicians, NOT a "do-it-yourselfer". They are written to inform these technicians of conditions that may occur on some vehicles, or to provide information that could assist in the proper service of a vehicle. Properly trained technicians have the equipment, tools, safety instructions, and know-how to do a job properly and safely. If a condition is described, DO NOT assume that the bulletin applies to your vehicle, or that your vehicle will have that condition. See your GM dealer for information on whether your vehicle may benefit from the information. WE SUPPORT VOLUNTARY TECHNICIAN CERTIFICATION