VOS-23-08

Service Information
Offboard Diagnostic Information System Service (ODIS Service)
Number: VOS-23-08
Subject: Software Version Update, Enhancements and Fixes
Date: April 7, 2023
Supersedes VOS-23-04 due to new diagnostic content
The following ODIS Service software versions are available for download.
Current ODIS Service Software Versions
Application: V11.0.1
Diagnostic Content: V2.47.9
Key Fixes/Enhancements for Diagnostic Content: V2.47.9:
1. Driver head curtain airbag igniter Resistance too high N251_X_1_0312_11_00011
- The vehicle voltage is: 0.0 V To continue the test, the following test requirements apply:
- Veh. sys. volt. greater than 9 volts.
- The voltage measured value is not read correctly. The vehicle voltage is greater than 9 volts. With
0.0 V and “NO” input, test requirement not met.
CA/CM Atlas 2018 – 2023.
2. High-voltage system, de-energize SYS_X_1_0214_HV_Spannungsfreiheit_herstellen_00000 Perform diagnostic power disconnection.
- Diagnostic power disconnection with active high-voltage system was unsuccessful.
- Voltage Electric Drive Control Module 2 - J944: 0.0 V.
- The #1 problem is that "diagnostic" de-energization is not possible, because it does not read the
voltage measured value from J944 front motor power electronics JX4.
E8 - ID.4 2021 - 2023.
3. High-voltage system, de-energize SYS_X_1_0214_HV_Spannungsfreiheit_herstellen_00000.
- The document showing connector unlocking information for the auxiliary connector is not correct.
E8 - ID.4 2021 - 2023.
4. B127801: Wire for video signal from front camera electrical error
SIG_X_J928_1_0915_11_Kameraleitungen_00000.
- ECF_SET_VALUE_ERROR
- The value Front camera quality for the request parameter Record Data Identifier could not be
entered.
E8 - ID.4 2021 - 2023.
5. P0A0600: Motor Electronics Coolant Pump "A" Control Circuit Low
V468_X_1_0920_11_KSY_FSB_EAE_Elektrische_Kuehlmittelpumpe_00000
© 2023 Volkswagen Group of America, Inc.
Page 1 of 3
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual
property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this
document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these
materials be modified or reposted to other sites, without the prior expressed written permission of the publisher.
Service Information
- There is a sporadic event memory entry stored relating to the component (Low temperature circuit
coolant pump -V468-) present.
- For this reason, there will only be a visual inspection of the connector and the electrical wires to
the component (Low temperature circuit coolant pump -V468-).
- Test states fault code P0A0600 is sporadic but fault remains active and static in the ECM and will
not clear.
E8 - ID.4 2021 - 2023.
6. B107804: Right rear center parking aid sensor faulty
G205_X_1_0619_11_alle_MXB_Fahrzeugtypen_00000 ODS5003E.
- Test step: Evaluate event memory
- Error ID: Infrastructure.GFS.ODS5003E
BW - Tiguan 2018 – 2023.
7. B10131B: Driver's Belt Force Limiter Resistance too high is set but no test plan provided in current
Test plans for the fault code.
E8 - ID.4 2021 - 2023.
8. B102201: Passenger occupant detection system control module electrical error
J706_X_1_0314_11_00000.
- Test step: Voltage
- The vehicle voltage is: 0.0
- The vehicle voltage measured value is not read correctly and greater than 9 volts. The vehicle
voltage is greater than 12 volts.
BW - Tiguan 2018 – 2023.
9. P044900: EVAP System Vent Valve Control Circuit/Open
SYS_X_1_0816_11_X_X_OBD1_XX_FSB_OBD1_N288_00011
- Set all performed measures back to their original state.
- P044900 is active/static in the ECM; test plan is inconclusive and ends without performing any
system diagnosis.
CL - Taos 2022 - 2023.
10. B116229: Selector lever park position lock switch Range/Performance
F319_X_1_0913_11_BCM_UDS_00011
Test step: wiring check: Test step states to perform a visual inspection and to check wires and
connectors between the following:
- Vehicle Electrical System Control Module - J519
- Selector Lever Park Position Lock Switch - F319
The wiring diagram and repair manual does not show the vehicle is equipped with F319.
AU - Golf 2013 – 2021
© 2023 Volkswagen Group of America, Inc.
Page 2 of 3
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual
property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this
document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these
materials be modified or reposted to other sites, without the prior expressed written permission of the publisher.
Service Information
11. B1B17F0: Parking Aid Control Module Trained parking function not available is active/static in
0076 - Parallel Parking Assistance.
- There is no test plan in current test plans for the fault code B1B17F0
E8 - ID.4 2021 - 2023.
12. B10001B: Driver airbag igniter Resistance too high N95_X_1_0312_11_00011
- Test step: Voltage
- The vehicle voltage is: 0.0
-The vehicle voltage measured value is not read correctly and greater than 9 volts. The vehicle
voltage is greater than 12 volts.
AU - Golf 2013 – 2021
13. B101C07: Driver seat belt switch mechanical malfunction E24_4M_XXXX_1_0614_11_00021
Test step: Malfunction type 11_STEP1/2.
- Insert seat belt into belt lock. Observe the current measuring value below. The readout must
indicate connected.
- Remove seat belt from belt lock. Observe the current measuring value below. The readout must
indicate not connected.
- Current measuring value is not read/displayed.
E8 - ID.4 2021 - 2023.
14. P06C500: Cylinder 1 Glow Plug Incorrect is active in the ECM, but no test added to current Test
Plan for the fault code.
16 - Jetta 2011 – 2018, CVCA 2.0l TDI SCR / 110 kW.
15. General translation errors.
© 2023 Volkswagen Group of America, Inc.
Page 3 of 3
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual
property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this
document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these
materials be modified or reposted to other sites, without the prior expressed written permission of the publisher.