TS45-FC-2304

SERVICE BULLETIN
Subject: General Software Improvement Bulletin
Bulletin Type: Field Fix Conditional
Bulletin No: TS45-FC-2304
PQR No:500000007246
Rev No: 00
Ref. No: 700004230
Vehicle Model: TS45
Flat Rate Time / Code:60 min
Date of issue: 31.03.2023
Modify Before: 31.03.2024
What to do with off coming parts:
What to do with outstanding parts of previous
revision:
☐ Scrap
☐Return
☐Use with additional parts
☐On consignment
☒ No off coming parts
☐Scrap
☐Return
☐Use with additional parts
☐On consignment
☒ No outstanding parts
Description of the modification:
The purpose of the bulletin is to ensure the
improvement of Handicapped Lift algorithm and
Multiviu brightness setting.
Bulletin Responsible: Abdulsamed ÇİFTCİOĞLU
Published & Approved By: Alper TEKNİKER
SERVICE BULLETIN
SAFETY INSTRUCTIONS
1. Mechanical Requested Dress Code
WARNING:
➢ Dress properly to avoid personal injury and damage to the
vehicle
✓
✓
✓
✓
✓
Always wear protective clothing
Do not wear any worn or loose-fitting clothing
Remove jewelry before starting to work
In case of long hair, use hairnet
The illustration on the left shows some of the correct and
incorrect clothing
✓ Sharp edged items should be avoided in order not to
scratch vehicle (i.e. belts, watches, necklace)
2. Protect Seats when Mechanic Starts Working
✓ Seats, trimming, upholstery stuff and carpeting should be
protected with appropriate coverings.
3. Welding on the Chassis
a. Always disconnect the batteries (starting with the negative lead).
b. Disconnect the connectors of electrical and electronic equipment (electronic control units,
sensors and actuators) if they are less than 2 meters away from the chassis part to be
welded or the earth terminal of the welding equipment.
c. The earth terminal should never be attached to vehicle components such as engine, axles
and springs. Arcing on these parts is not permitted, because of the risk of damage to
bearings, springs, etc.
d. The earth terminal must make good contact and be placed as close as possible to the part to
be welded.
e. Plastic pipes, rubber parts and parabolic springs should be well protected against welding
spatter and temperatures higher than 70°.
f. The contact switch must not be in the accessory or contact position. The contact key should
be removed.
g. Reconnect in reversed order of disconnecting. Ensure that a good earth connection is made
between chassis, engine and cab.
SERVICE BULLETIN
The program Link
Kibes :
** TS00-LC3-019 software should be installed on vehicles with software starting with
TS00-LC3-…
https://content.temsa.com/sapcs?get&pVersion=0045&contRep=ZADNSPEKTEP07101&docId=90E2BA0455251EDDB
3931F6943D45F56&accessMode=r&compId=TS00-LC3-019.7z
Multiviu :
**TS00-MV-026 software should be installed on vehicles with software starting with
TS00-MV-…
https://content.temsa.com/sapcs?get&pVersion=0045&contRep=ZADNSPEKTEP07101&docId=90E2BA0455251EDDB
392C07A4C42DF56&accessMode=r&compId=TS00_MV_026.L2P.7z
Uploading the up to date program(Kibes):
1- Park the vehicle to an area which is proper to work.
SERVICE BULLETIN
2- To install the KIBES software, locate the KIBES socket next to the OBD socket by looking at the label
on the cover.
3- Connect one end of the KIBES cable to the CANalyzer or Peak cable and the other end to the KIBES
diagnostic socket. Connect the CANalyzer or Peak output to the computer. Make sure that the KIBES
dongle is inserted to your computer.
SERVICE BULLETIN
SERVICE BULLETIN
4- Install the KIBES software on the vehicle as described in the images. Turn the ignition switch on. Do not
start the engine.
SERVICE BULLETIN
Hint: The software version must be selected correctly. The number shown in the picture may be
representative.
SERVICE BULLETIN
SERVICE BULLETIN
Click "Preferences" to check the Baudrate and port. (for TS Coachs 250000)
SERVICE BULLETIN
Click on the instruction shown in order in the picture.
2.click
here
1.click
here
SERVICE BULLETIN
3.click
here
SERVICE BULLETIN
Uploading the up to date program (Multiviu):
1-Park the vehicle to an area which is proper to work.
2-Connect your computer to the vehicle by using the CANalyzer interface. Plug the USB part into your
computer and connect your CAN cable to the 9 pinned OBD port with the D pin low and the C pin high.
D
C
SERVICE BULLETIN
3- Turn the ignition switch on. Do not start the engine.
4- Make sure that the KIBES dongle is inserted to your computer.
SERVICE BULLETIN
5- Select the “Open Project” selection and click “next”.
SERVICE BULLETIN
Click here
5- Select TS00_MV_026. Then click “ok” after that click “Finish”.
Hint: The software version must be selected correctly. The number shown in the picture may be
representative.
SERVICE BULLETIN
Make sure you
choose the
right program.
!
SERVICE BULLETIN
7-Right click on Mulviu then click “Communication Settings” check the Port and Baudrate.
You can change port
here. Please make
sure correct port.
You can change
“Download Baudrate”
here
You can change
“Start Baudrate”
here
SERVICE BULLETIN
8-Right click on Mulviu again then click “Archive Download”
SERVICE BULLETIN
Click here
9- You should find program in your workspace then double click the program.
SERVICE BULLETIN
SERVICE BULLETIN
SERVICE BULLETIN
10- Click on “MRT” then click “Open”.
Make sure you choose the right program here!
SERVICE BULLETIN
11- After the software is checked, click the “Build New Archive”, then click the “Archive
Download” .
12-When a warning occurs, click OK, then wait for the program to be downloaded. Do not cut the
power off during the download process, this could cause the body controller to dysfunction .
Vehicle List
#
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
VIN
NLTEJXA94M1000329
NLTEJXA92M1000328
NLTEJXA96N1000334
NLTEJXA99N1000330
NLTEJXA90N1000331
NLTEJXA92N1000332
NLTEJXA90P1000333
NLTEJXA98N1000335
NLTEJXA9XN1000336
NLTEJXA91N1000337
NLTEJXA9XP1000338
NLTEJXA95N1000339
NLTEJXA91N1000340
NLTEJXA93N1000341
NLTEJXA95N1000342
NLTEJXA97N1000343
NLTEJXA95P1000344
NLTEJXA90N1000345
NLTEJXA92N1000346
NLTEJXA94N1000347
NLTEJXA92P1000348
NLTEJXA94P1000349
NLTEJXA90P1000350
NLTEJXA92P1000351
NLTEJXA94P1000352
NLTEJXA96P1000353
NLTEJXA93P1000357
NLTEJXA95P1000358
NLTEJXA97P1000359
Country
US
US
US
US
US
US
US
US
US
US
US
US
US
US
US
US
US
US
US
US
US
US
US
US
US
US
US
US
US
SERVICE BULLETIN
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
NLTEJXA9XP1000355
NLTEJXA98P1000354
NLTEJXA91P1000356
NLTEJXA93P1000360
NLTEJXA95P1000361
NLTEJXA97P1000362
NLTEJXA99P1000363
NLTEJXA90P1000364
NLTEJXA92P1000365
NLTEJXA94P1000366
NLTEJXA96P1000367
NLTEJXA98P1000368
NLTEJXA9XP1000369
NLTEJXA96P1000370
NLTEJXA98P1000371
NLTEJXA9XP1000372
NLTEJXA91P1000373
NLTEJXA93P1000374
NLTEJXA95P1000375
NLTEJXA97P1000376
NLTEJXA99P1000377
NLTEJXA90P1000378
NLTEJXA92P1000379
NLTEJXA99P1000380
NLTEJXA90P1000381
NLTEJXA92P1000382
NLTEJXA94P1000383
NLTEJXA96P1000384
NLTEJXA98P1000385
NLTEJXA9XP1000386
NLTEJXA91P1000387
NLTEJXA93P1000388
NLTEJXA95P1000389
NLTEJXA91P1000390
NLTEJXA93P1000391
NLTEJXA95P1000392
NLTEJXA97P1000393
NLTEJXA91P1000423
NLTEJXA99P1000394
NLTEJXA90P1000395
NLTEJXA92P1000396
NLTEJXA94P1000397
NLTEJXA96P1000398
US
US
US
US
US
US
US
US
US
US
US
US
US
US
US
US
US
US
US
US
US
US
US
US
US
US
US
US
US
US
US
US
US
US
US
US
US
US
US
US
US
US
US
SERVICE BULLETIN
73
74
75
76
77
78
79
80
81
82
NLTEJXA98P1000399
NLTEJXA90P1000400
NLTEJXA92P1000401
NLTEJXA94P1000402
NLTEJXA96P1000403
NLTEJXA98P1000404
NLTEJXA94P1000433
NLTEJXA96P1000434
NLTEJXA9XP1000405
NLTEJXA91P1000406
US
US
US
US
US
US
US
US
US
US
LABOR BREAKDOWN
Application
Time
Uploading the up-to-date Kibes and Multiviu program.
60
Total Labor Time
60