TSB001313
Service Bulletin Details
Public Details for: TSB001313
Tt: some 2007 ? 2012 model year tundra vehicles may exhibit a rubbing or grinding noise from the rear when making left-hand or right-hand turns. New parking brake plate sub-assemblies have been developed to address this condition.
- 2012 - 2011 - 2010 - 2009 - 2008 - 2007 -
Models from 2012
2012 TOYOTA TUNDRA |
Models from 2011
2011 TOYOTA TUNDRA |
Models from 2010
2010 TOYOTA TUNDRA |
Models from 2009
2009 TOYOTA TUNDRA |
Models from 2008
2008 TOYOTA TUNDRA |
Models from 2007
2007 TOYOTA TUNDRA |
T-SB-0013-13 Rev1 January 29, 2013 Rubbing or Grinding Noise From Rear on Turns Service Category Brake Section Brake (rear) Market USA Applicability YEAR(S) MODEL(S) 2007 - 2012 Tundra ADDITIONAL INFORMATION REVISION NOTICE February 20, 2023 Rev1: • The Parts Information and Repair Procedure sections have been updated. Any previous printed versions of this bulletin should be discarded. Introduction Some 2007 – 2012 model year Tundra vehicles may exhibit a rubbing or grinding noise from the rear when making left-hand or right-hand turns. New parking brake plate sub-assemblies have been developed to address this condition. Warranty Information OP CODE DESCRIPTION TIME BR1210 R & R Parking Brake Sub-assembly** 2.2 Combo A Opposite Side 1.0 OFP T1 T2 46503-#####* 46504-#####* 36 13 *Special Service Part Bearing Kit can no longer be ordered. Replace ALL parts with new ones listed in the Parts Information section of this bulletin. **Warranty claim MUST be submitted with the correct 10-digit OFP. Choose the correct OFP for the vehicle being repaired by searching for the parts in the Electronic Parts Catalog using the VIN filter. APPLICABLE WARRANTY • This repair is covered under the Toyota Basic Warranty. This warranty is in effect for 36 months or 36,000 miles, whichever occurs first, from the vehicle’s in-service date. • Warranty application is limited to occurrence of the specified condition described in this bulletin. © 2022 Toyota Motor Sales, USA Page 1 of 5 T-SB-0013-13 Rev1 January 29, 2013 Page 2 of 5 Rubbing or Grinding Noise From Rear on Turns Parts Information PART NUMBER PREVIOUS 04002-4310C 04002-4320C PART NAME QTY 42423-34040 Retainer, RR, Axle Bearing, Inner 1 42450-0C011 Bearing Assy, RR Axle W/ABS Rotor, RH 1 46503-0C012 Plate Sub-Assy, Parking Brake, RH 1 90119-A0276 Bolt, W/Washer 2 90301-A0015 Ring, O 1 90310-A0004 Seal, Type S Oil 1 90468-08035 Clip 1 42423-34040 Retainer, RR, Axle Bearing, Inner 1 42460-0C011 Bearing Assy, RR Axle W/ABS Rotor, LH 1 46504-0C012 Plate Sub-Assy, Parking Brake, LH 1 90119-A0276 Bolt, W/Washer 2 90301-A0015 Ring, O 1 90310-A004 Seal, Type S Oil 1 90468-08035 Clip 1 NEW © 2022 Toyota Motor Sales, USA T-SB-0013-13 Rev1 January 29, 2013 Page 3 of 5 Rubbing or Grinding Noise From Rear on Turns Required Tools & Equipment SPECIAL SERVICE TOOLS (SST) PART NUMBER Oil Seal Puller** 09308-00010 Brake Shoe Return Spring Tool* 09703-30011 1 Shoe Hold Down Spring Driver* 09718-00011 1 Rear Axle Shaft Puller** 09521-25011-01 1 Rear Axle Shaft Puller Adapter** 09521-60010-01 1 Rear Axle Shaft Puller Spacer** 09521-25000-01 Seal Ring Tool** 09631-12090 1 Lower Control Shaft Bearing Replacer* 09726-40010 1 Replacer Set #3** (Replacer 110) 09950-60030-01 (09951-01100-01) 1 Outer Bearing Cup Replacer* 09950-60020 1 Handle Set** 09950-70010-01 1 *Special order. **Essential SST. NOTE Additional SSTs may be ordered by calling 1-800-933-8335. © 2022 Toyota Motor Sales, USA QTY T-SB-0013-13 Rev1 January 29, 2013 Page 4 of 5 Rubbing or Grinding Noise From Rear on Turns Repair Procedure 1. Test-drive the vehicle and confirm the condition exists. Does the vehicle exhibit a rubbing or grinding noise from the rear when making left-hand and right-hand turns? • YES — Continue to step 2. • NO — This bulletin does NOT apply. Continue diagnosis using the applicable Repair Manual. 2. Place the vehicle on the lift, remove the rear wheels and rear rotors, and check for any irregular contact on the brake plate from the rotors. Figure 1. Example of Irregular Contact on Brake Plate 3. If there appears to be irregular contact from the rotor to the brake plate, replace ALL parts specified in the Special Service Part Bearing Kit (including the parking brake backing plate). Refer TIS, applicable model year Repair Manual: • 2007 Tundra: Drivetrain – Axle/Differential – “Axle: Rear Axle Shaft: Removal / Disassembly / Reassembly / Installation” • 2008 Tundra: Drivetrain – Axle/Differential – “Axle: Rear Axle Shaft: Removal / Disassembly / Reassembly / Installation” • 2009 Tundra: Drivetrain – Axle/Differential – “Axle: Rear Axle Shaft: Removal / Disassembly / Reassembly / Installation” • 2010 Tundra: Drivetrain – Axle/Differential – “Axle: Rear Axle Shaft: Removal / Disassembly / Reassembly / Installation” © 2022 Toyota Motor Sales, USA T-SB-0013-13 Rev1 January 29, 2013 Page 5 of 5 Rubbing or Grinding Noise From Rear on Turns Repair Procedure (continued) 4. Settle the parking brake shoe and disc. A. Drive the vehicle for approximately 0.25 miles (400 m) under the following conditions: (1) Drive the vehicle at approximately 31 mph (50 km/h) on a level, dry road. (2) Depress the parking brake pedal. B. Repeat the procedure above two or three times. C. Stop and depress the parking brake three times. The vehicle should hold position with six to nine clicks of travel. 5. Test-drive the vehicle once more to confirm there is NO noise coming from the rear of the vehicle when making left-hand and right-hand turns. © 2022 Toyota Motor Sales, USA