A3523442070217_1

Technical Service Bulletin
35 Gearbox warning comes on, various DTC memory entries in TCM
35 23 44 2070217/1 September 15, 2023.
Model(s)
A3, and RS 3
S3
Year
VIN Range
Vehicle-Specific Equipment
All
Not Applicable
2017 – 2020
2022 – 2024
2018 – 2020
2022 – 2024
TT, and TT
Roadster
2018 – 2023
TTS
2019 - 2023
TT RS
2018 - 2022
Condition
Customer states:
• The vehicle shudders while driving.
and
• The gearbox warning lamp is illuminated.
and/or
• The message “Gearbox Malfunction” appears on the instrument cluster display.
and/or
• The gearbox only changes gear in Limp Home Mode; it is only possible to drive in the gears 1-3-5-7 or 2-4-6.
Workshop findings:
• One or more of the customer statements can be reproduced.
• One or more of the following DTC(s) may be stored in the transmission control module (TCM), -J217- (address
word 0002):
Description
Gearbox
Type
10666
Clutch position sensor 1, electrical malfunction
0GC/0DL
10668
Clutch position sensor 2, electrical malfunction
0GC/0DL
DTC Entry
Symptom Code
P173500
P173600
© 2023 Audi of America, Inc.
Page 1 of 21
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other
intellectual property rights of Audi of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this
document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may
these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher.
Technical Service Bulletin
P175D00
10693
Clutch 1 opens unintentionally
0GC/0DL
P176E00
10694
Clutch 2 opens unintentionally
0GC/0DL
P175E00
10747
Clutch 1 closes unintentionally
0GC/0DL
P176F00
10748
Clutch 2 closes unintentionally
0GC/0DL
P060700
10658
Control module implausible
0GC/0DL
P060700
10660
Control module implausible
0GC/0DL
P060700
10662
Control module implausible
0GC/0DL
P060700
10664
Control module implausible
0GC/0DL
P176A00
10912
Gear selector 1 cannot be regulated
0GC/0DL
P176B00
10913
Gear selector 2 cannot be regulated
0GC/0DL
P176C00
10914
Gear selector 3 cannot be regulated
0GC/0DL
P176D00
10915
Gear selector 4 cannot be regulated
0GC/0DL
P176A00
10725
Gear selector 1 cannot be regulated
0GC/0DL
P176B00
10726
Gear selector 2 cannot be regulated
0GC/0DL
P176C00
10727
Gear selector 3 cannot be regulated
0GC/0DL
P176D00
10728
Gear selector 4 cannot be regulated
0GC/0DL
P071500
10753
Transmission Input Speed Sensor 1, electrical fault in
circuit
0GC/0DL
P276500
10754
Transmission Input Speed Sensor 2, electrical fault in
circuit
0GC/0DL
P174A00
10739
Valve 3 in partial transmission 1 electrical malfunction
0DL
P174E00
10740
Valve 3 in partial transmission 2 electrical malfunction
0DL
P173E00
10741
Valve 1 in partial transmission 1 electrical malfunction
0DL
P174C00
10742
Valve 1 in partial transmission 2 electrical malfunction
0DL
P173F00
10743
Valve 2 in partial transmission 1 electrical malfunction
0DL
P174D00
10744
Valve 2 in partial transmission 2 electrical malfunction
0DL
© 2023 Audi of America, Inc.
Page 2 of 21
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other
intellectual property rights of Audi of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this
document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may
these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher.
Technical Service Bulletin
Technical Background
Hardware issue in transmission control unit.
Production Solution
Not applicable.
Service
1.
The Software part number and Software Version number and of the Transmission control unit must first be
checked (Figure 1).
Figure 1. Software part number and Software version number.
2.
If the installed Software part number and Software version number is not included in the table below, then
this TSB does not apply. Continue the diagnosis and repair outside of this TSB.
3.
If the installed Software part number and Software version number is included in the table below continue
with the TSB instructions.
Software Part Number Software Version Number
0GC300042J
1402
0GC300012A
1403
0GC300012M
2308
0GC300013M
2401
0GC300013M
2402
0GC300013N
2404
0GC300014B
2405
© 2023 Audi of America, Inc.
Page 3 of 21
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other
intellectual property rights of Audi of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this
document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may
these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher.
Technical Service Bulletin
0GC300014B
2406
0GC300043A
2303
0GC300044H
2402
0DL300012H
2111
0DL300012H
2112
0DL300013E
3020
0DL300013E
3023
0DL300013L
3104
0DL300013L
3101
Tip: Offboard Diagnostic Information System Service: In the Offboard Diagnostic Information
System (ODIS), the baseline version (diagnosis data – didb_GFS-a) 2023.03.01 / 2.30.5 or higher must
be installed (Figure 2).
Figure 2. ODIS Version.
4. It is only possible to deliver the correct control
unit if 89 values are read out and transmitted in
the global variables under the address DA0002
at the start of the diagnostic session. To check
this, save the diagnostic protocol (Figure 3) to the
desktop of the scan tool and open it
Figure 3. Save Diagnosis Log.
© 2023 Audi of America, Inc.
Page 4 of 21
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other
intellectual property rights of Audi of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this
document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may
these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher.
Technical Service Bulletin
5. Click the + to expand the “Global Variables”
(Figure 4).
Figure 4. Global Variables.
6. With the “Global Variables” expanded (Figure 5), there should be a long list of values.
Figure 5. Global Variables Expanded
7. Check the global variables; there should be a long list of values with the title DA0002 ending with
the values “STOPP”.
Figure 6. Global Variables DA0002.
There should be 89 values stored with the title DA0002. Quickly check if there are 89 values by
performing a “Search text” or “Find” (Control +F) in the browser window; search for DA0002 to
verify that the number of results is 89 (Figure 7).
© 2023 Audi of America, Inc.
Page 5 of 21
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other
intellectual property rights of Audi of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this
document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may
these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher.
Technical Service Bulletin
Figure 7. Search Text / 89 Values.
Tip: It is only possible to receive the correct control unit if the diagnostic log was sent with
the relevant event memory entry, the completed test plan, and the 89 values shown in the Global
Variables.
8. If there are less than 89 values this TSB repair will not work, and it does not apply to the
vehicle. Repairs should be made outside this TSB according to ODIS test plans and the
repair manual.
9. Perform Guided Fault Finding for the relevant event memory entry and follow the instructions.
10. Answer ‘YES’ to the question “Could you locate relevant Technical Service Bulletin (TSB)” or
“Could you locate relevant Technical Product Information (TPI)?”
If the test plan requests a TSB or TPI number enter: 2058356
11. Continue with the test plan, and the following message will come up with important information
you need for parts ordering (Figure 8). Make note of the 4 letter index of the Mechatronic and
compare it to the parts list table in this TSB. If the index shown in the test plan is available in one
of the parts list below answer the test plan question with “Yes” if the 4 letter index of the
Mechatronic is not shown available in one of the parts list below answer the test plan question
with “No” and this TSB doesn’t apply to the vehicle.
© 2023 Audi of America, Inc.
Page 6 of 21
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other
intellectual property rights of Audi of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this
document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may
these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher.
Technical Service Bulletin
• Figure 8. Index of the Mechatronic and test plan question.
12. If the index shown in the test plan is available in one of the parts lists below, and the test plan
was finished correctly, upload the GFF log to GFF paperless and order the correct parts
from one of the tables below. Read all notes in the parts information section of this TSB.
Tip: The immobilizer must be readapted after replacing the control unit. For this purpose, it
is essential that all vehicle keys are present at the time of the repair.
13. After receiving the required genuine parts, remove mechatronics unit from gearbox according to
the repair manual.
14. The sensors are on the back of the mechatronics unit and must not be touched/damaged. The
mechatronic unit must not be placed down on its sensors (Figure 9, red markings).
© 2023 Audi of America, Inc.
Page 7 of 21
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other
intellectual property rights of Audi of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this
document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may
these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher.
Technical Service Bulletin
Figure 9. Mechatronics Sensors
Note:
For this repair the special tool VAS 6613 ESD Work Surface is required
Touch a suitable earthed object (VAS 6613 ESD Work Surface) before working on electrical
components of mechatronic unit. Do not touch the contacts or electronic components directly
Note:
You must ensure the highest levels of cleanliness for all work on the mechatronic unit. Even the
smallest dirt particles or hairs in the system can lead to restricted functions and ultimately to
failure of the mechatronic unit.
15. After removing the mechatronic unit, place it in the assembly aid to protect the sensors. The
assembly aid comes with the new control unit. First take the control unit out of the assembly aid
and store it safely in the packaging. Place the mechatronic unit in the assembly aid (Figure 10)
with sensors facing downwards.
© 2023 Audi of America, Inc.
Page 8 of 21
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other
intellectual property rights of Audi of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this
document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may
these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher.
Technical Service Bulletin
Figure 10. Mechatronics unit in the assembly aid.
16. The contact plate must be detached from the mechatronic unit. To do so, loosen and remove the
bolts (Figure 11 - 0GC Transmission or Figure 12 - 0DL Transmission).
© 2023 Audi of America, Inc.
Page 9 of 21
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other
intellectual property rights of Audi of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this
document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may
these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher.
Technical Service Bulletin
Figure 11: Contact plate bolts – 0GC
transmission.
Figure 12: Contact plate bolts 0DL transmission.
17. Starting at the top corners, detach the contact plate (figure 13, red marking) carefully and evenly
(without levering it upwards) from the mechatronic unit. It is essential to ensure that the contacts
on the valves are not bent or damaged.
© 2023 Audi of America, Inc.
Page 10 of 21
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other
intellectual property rights of Audi of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this
document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may
these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher.
Technical Service Bulletin
Figure 13. Removing contact plate.
18. Take the mechatronic unit out of the assembly aide, turn the mechatronic unit over, and place it
back in the assembly aid (Figure 14). When doing so, take care not to damage the valve contacts
and the sensors.
© 2023 Audi of America, Inc.
Page 11 of 21
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other
intellectual property rights of Audi of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this
document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may
these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher.
Technical Service Bulletin
Figure 14. Mechatronic unit with the control unit in the assembly aide facing upwards.
19. Move the connecting tab between the contact plate and the control unit in the direction of the
arrow (less than 10°) (Figure 15, red arrow). When it is in place, the connecting tab engages in
the correct position with an audible click.
© 2023 Audi of America, Inc.
Page 12 of 21
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other
intellectual property rights of Audi of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this
document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may
these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher.
Technical Service Bulletin
Figure 15. Connecting tab between the contact plate and the control unit.
20. Unscrew the 4 bolts (Figure 16) (A, D short and B, C long), then carefully detach the gearbox
control unit upwards from the mechatronic unit.
© 2023 Audi of America, Inc.
Page 13 of 21
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other
intellectual property rights of Audi of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this
document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may
these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher.
Technical Service Bulletin
Figure 16. Bolts for the transmission control unit.
21. Replace the seals for the pressure sensors (Figure 17). When doing so, ensure that the seals are
seated correctly.
Figure 17. Seals for the pressure sensors.
22. Remaining assembly is performed in reverse sequence.
Tighten the control unit with new bolts in 2 stages (Figure 16).
Stage 1:
• Bolts A and D (short): 6 Nm
© 2023 Audi of America, Inc.
Page 14 of 21
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other
intellectual property rights of Audi of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this
document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may
these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher.
Technical Service Bulletin
• Bolts B and C (long): 4.5 Nm
Stage 2:
• Bolts A and D (short): 8 Nm + 30°
• Bolts B and C (long): 5 Nm + 25°
23. Fit the new contact plate, making sure it engages audibly on the contacts.
When pressing the contact plate on, it is essential to ensure that all of the contacts are inserted
in the intended/correct connector and do not get bent (Figure 18 and Figure 19).
Figure 18. Correct contact, circled.
Figure 19. Bent contact, circled.
24. Tighten the contact plate with new bolts in specified sequence in 2 stages.
• For 0GC Transmission (figure 20):
• For 0DL Transmission (figure 21):
• Stage 1: 2 Nm
• Stage 1: 2 Nm
• Stage 2: 3 Nm + 30°
• Stage 2: 3 Nm + 45°
• Tightening sequence: 1 -> 2 -> 3 -> 12 -> 5 -> 4 ->
11 -> 10 -> 9 -> 8 -> 6 -> 7
• Tightening sequence: 1 -> 2 -> 3 -> 4 > 5 -> 6 -> 7 -> 8 -> 9 -> 10 -> 11
© 2023 Audi of America, Inc.
Page 15 of 21
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other
intellectual property rights of Audi of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this
document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may
these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher.
Technical Service Bulletin
Figure 20. Contact Plate Bolts 0GC Transmission.
Figure 21.Contact Plate Bolts 0DL
Transmission.
25. Reassemble the mechatronics unit with new cover into the transmission, including refilling the
transmission with oil according to the repair manual.
26. Activate the new control unit using the Guided Function “0002 - Replace mechatronic unit
(control unit)”.
27. Perform basic setting for gearbox.
Warranty
Claim Type:
• 110 up to 48 Months/50,000 Miles.
• G10 for CPO Covered Vehicles – Verify Owner.
• If the vehicle is outside any warranty, this Technical Service Bulletin is informational
only.
Service Number:
3511
Damage Code:
0040
Labor Operations: Remove and install mechatronic unit
Repair mechatronic unit
© 2023 Audi of America, Inc.
3511 19xx
See SRT(s) with
associated
operation.
3511 4199
50 TU
Page 16 of 21
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other
intellectual property rights of Audi of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this
document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may
these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher.
Technical Service Bulletin
Diagnostic Time:
GFF
0150 0000
Time stated on
diagnostic
protocol (Max 120
TU)
Road test prior to service procedure
No allowance
0 TU
Road test after service procedure
No allowance
0 TU
As per TSB 2070217/1
Claim Comment:
All warranty claims submitted for payment must be in accordance with the Audi Warranty Policies and Procedures
Manual. Claims are subject to review or audit by Audi Warranty.
Required Parts and Tools
Note:
Parts cannot be ordered until Step 11 of this TSB has been completed and the index of the Mechatronics
unit is shown in one of the lists below! It is only possible to deliver the correct control unit if the
diagnostic log was sent online with the relevant DTC entry and the completed test plan.
Note:
Only order parts for the correct index of the Mechatronics unit! If the installed mechatronics unit does not
have index that matches one of the parts tables below this TSB does not apply to the vehicle!
Note:
Red Order all parts using the VIN of vehicle when ordering!
Always check with your Parts Department and/or ETKA for the latest information and parts bulletins.
Transmission Service Code: 0GC (A3 and TT)
Index of Mechatronics unit 0GCB, 0GCC or 0GCD Parts list:
Part Number
Part Description
Quantity
See ETKA
Fasteners, Bolts, Nuts and Screws as needed per the
Repair Manual
See ETKA/ELSA
0GC 927 711 G VI1 Control unit
01
0GC 927 709 A
Contact plate
01
N 101 243 04
Bolt for control unit (short)
02
N 104 057 05
Bolt for control unit (long)
02
© 2023 Audi of America, Inc.
Page 17 of 21
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other
intellectual property rights of Audi of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this
document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may
these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher.
Technical Service Bulletin
N 904 552 02
Bolt for contact plate
12
WHT 004 007 B
O-ring for pressure sensor
02
0GC 325 201 H
Cover for mechatronic unit
01
N 105 540 02
Bolt for mechatronic unit
09
N 910 327 02
Bolt for cover for mechatronic unit
04
0BH 325 147
Retaining clip
01
N 043 809 2
Oil seal
01
G 055 529 A2
Gear oil
07
Always check with your Parts Department and/or ETKA for the latest information and parts bulletins.
Transmission Service Code: 0GC (A3 and TT)
Index of Mechatronics unit 0GCE or 0GCH Parts list:
Part Number
Part Description
Quantity
See ETKA
Fasteners, Bolts, Nuts and Screws as needed per the
Repair Manual
See ETKA/ELSA
0GC 927 711 H VI1 Control unit
01
0GC 927 709 A
Contact plate
01
N 101 243 04
Bolt for control unit (short)
02
N 104 057 05
Bolt for control unit (long)
02
N 904 552 02
Bolt for contact plate
12
WHT 004 007 B
O-ring for pressure sensor
02
0GC 325 201 H
Cover for mechatronic unit
01
N 105 540 02
Bolt for mechatronic unit
09
N 910 327 02
Bolt for cover for mechatronic unit
04
0BH 325 147
Retaining clip
01
N 043 809 2
Oil seal
01
G 055 529 A2
Gear oil
07
© 2023 Audi of America, Inc.
Page 18 of 21
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other
intellectual property rights of Audi of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this
document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may
these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher.
Technical Service Bulletin
Always check with your Parts Department and/or ETKA for the latest information and parts bulletins.
Transmission Service Code: 0DL (RS3 and TTRS)
Index of Mechatronics unit 0GC* (*Any 4th digit) Parts list:
Part Number
Part Description
Quantity
See ETKA
Fasteners, Bolts, Nuts and Screws as needed per the
Repair Manual
See ETKA/ELSA
0GC 927 711 H VI1 Control unit
01
0GC 927 709 A
Contact plate
01
N 101 243 04
Bolt for control unit (short)
02
N 104 057 05
Bolt for control unit (long)
02
N 904 552 02
Bolt for contact plate
12
WHT 004 007 B
O-ring for pressure sensor
02
0GC 325 201 H
Cover for mechatronic unit
01
N 105 540 02
Bolt for mechatronic unit
09
N 910 327 02
Bolt for cover for mechatronic unit
04
0BH 325 147
Retaining clip
01
N 043 809 2
Oil seal
01
N 013 813 2
Oil seal
01
G 052 182 A2
Gear oil
07
Always check with your Parts Department and/or ETKA for the latest information and parts bulletins.
Transmission Service Code: 0DL (RS3 and TTRS)
Index of Mechatronics unit 0BH* (*Any 4th digit) Parts list:
Part Number
Part Description
Quantity
See ETKA
Fasteners, Bolts, Nuts and Screws as needed per the
Repair Manual
See ETKA/ELSA
0GC 927 711 H VI1 Control unit
© 2023 Audi of America, Inc.
01
Page 19 of 21
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other
intellectual property rights of Audi of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this
document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may
these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher.
Technical Service Bulletin
0BH 927 709 A
Contact plate
01
N 101 243 04
Bolt for control unit (short)
02
N 104 057 05
Bolt for control unit (long)
02
N 904 552 02
Bolt for contact plate
11
WHT 004 007 B
O-ring for pressure sensor
02
0GC 325 201 H
Cover for mechatronic unit
01
N 105 540 02
Bolt for mechatronic unit
09
N 910 327 02
Bolt for cover for mechatronic unit
04
0BH 325 147
Retaining clip
01
N 043 809 2
Oil seal
01
N 013 813 2
Oil seal
01
G 052 182 A2
Gear oil
07
Always check with your Parts Department and/or ETKA for the latest information and parts bulletins.
Transmission Service Code: 0DL (RS3 and TTRS)
Index of Mechatronics unit 0DL* (*Any 4th digit) Parts list:
Part Number
Part Description
Quantity
See ETKA
Fasteners, Bolts, Nuts and Screws as needed per the
Repair Manual
See ETKA/ELSA
0GC 927 711 H VI1 Control unit
01
0BH 927 709 A
Contact plate
01
N 101 243 04
Bolt for control unit (short)
02
N 104 057 05
Bolt for control unit (long)
02
N 904 552 02
Bolt for contact plate
11
WHT 004 007 B
O-ring for pressure sensor
02
0GC 325 201 H
Cover for mechatronic unit
01
N 105 540 02
Bolt for mechatronic unit
09
© 2023 Audi of America, Inc.
Page 20 of 21
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other
intellectual property rights of Audi of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this
document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may
these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher.
Technical Service Bulletin
N 910 327 02
Bolt for cover for mechatronic unit
04
0BH 325 147
Retaining clip
01
N 043 809 2
Oil seal
01
N 013 813 2
Oil seal
01
G 052 182 A2
Gear oil
07
Special Tools Required:
•
VAS 6613 ESD Work Surface
Additional Information
All parts and service references provided in this TSB (2070217) are subject to change and/or removal.
©2023 Audi of America, Inc. All rights reserved. The information contained in this document is based on the
latest information available at the time of printing and is subject to the copyright and other intellectual property
rights of Audi of America, Inc., its affiliated companies, and its licensors. All rights are reserved to make changes
at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or
transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may
these materials be modified or reposted to other sites without the prior expressed written permission of the
publisher.
© 2023 Audi of America, Inc.
Page 21 of 21
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other
intellectual property rights of Audi of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this
document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may
these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher.