24-BD-002G
Service Bulletin Details
Public Details for: 24-BD-002G
This bulletin provides instructions to inspect and realign the panoramic sunroof on certain gv70 (jk1a) and gv70 electrified (jk1a ev) vehicles to reduce excessive wind noise conditions. This bulletin only applies if the excessive wind nois
Models from 2024
2024 GENESIS GV70 |
2024 GENESIS GV70 EV |
Models from 2023
2023 GENESIS GV70 EV |
GROUP NUMBER BODY DATE Technical Service Bulletin SUBJECT: 24-BD-002G MODEL(S) FEBRUARY 2024 GV70 (JK1A) GV70 ELECTRIFIED (JK1A EV) EXCESSIVE WIND NOISE FROM PANORAMIC SUNROOF Description: This bulletin provides instructions to inspect and realign the panoramic sunroof on certain GV70 (JK1A) and GV70 Electrified (JK1A EV) vehicles to reduce excessive wind noise conditions. This bulletin only applies if the excessive wind noise condition has been isolated to the panoramic sunroof. Applicable Vehicles (Certain): • 2024MY GV70 (JK1A) produced from 12/7/2022 – 9/30/2023. • 2023-2024MY GV70 Electrified (JK1A EV) produced from 1/25/2023 – 9/30/2023. NOTICE Genesis EV repairs can only be performed by Genesis EV Certified Retailers. Parts Information: Model Part Name Figure GV70 (JK1A) GV70 Electrified Plastic Shims (JK1A EV) NOTE: Plastic shims can be purchased at local hardware retailers. Remarks 1/16 inch (0.1 inch) or 2.5 mm minimum thickness Warranty Information: Model GV70 (JK1A) GV70 Electrified (JK1A EV) Op. Code 81600FF1 Operation Realignment of the Panoramic Sunroof Op. Time Causal Part Nature Code Cause Code 2.8 M/H Refer to WebLTS for applicable part to labor Op Code combination Q11 ZZ1 NOTE 1: Normal warranty applies. NOTE 2: Submit claim on Claim Entry Screen as “Warranty” type. NOTE 3: Refer to the latest Digital Documentation Policy for repair validation requirements. NOTE 4: If a part is found in need of replacement while performing this TSB and the affected part is still under warranty, submit a separate claim using the same repair order. If the affected part is out of warranty, submit a Prior Approval request for goodwill consideration prior to performing the work. NOTE 5: Dealer may include reimbursement for purchased plastic shims under sublet. Circulate To: General Manager, Service Manager, Parts Manager, Warranty Manager, Service Advisors, Technicians, Body Shop Manager, Fleet Repair SUBJECT: EXCESSIVE WIND NOISE FROM PANORAMIC SUNROOF Service Procedure: STUI This TSB includes Repair validation photos. Refer to the latest Digital Documentation Policy for requirements. 1. Using calipers, measure the distance between the edge of the sunroof glass (A) and the roof body panel (B) at the indicated locations in the diagram: • • If any of the 4 measurements are outside the specified range of 12.0 – 14.0 mm, then proceed to the next step. If all 4 measurements are within the specified range of 12.0 – 14.0 mm, this TSB does NOT apply. Please refer to the shop manual for further repair diagnosis. B A FR FL ↑Front RL TSB #: 24-BD-002G RR Page 2 of 4 SUBJECT: SUBJECT: 2. EXCESSIVE WIND NOISE FROM PANORAMIC SUNROOF Remove and lower the headliner (A). A Refer to the shop manual: • Body (Interior and Exterior) > Roof Trim > Roof Trim Assembly > Replacement OR Removal and Installation i Information The headliner does NOT need to be removed from the vehicle. 3. Loosen the 14 mounting nuts of the sunroof assembly (B). It is NOT necessary to remove the mounting nuts. 4. B Place a shim on each section of the panoramic sunroof to prevent excessive movement during adjustment. TSB #: 24-BD-002G Page 3 of 4 SUBJECT: SUBJECT: 5. EXCESSIVE WIND NOISE FROM PANORAMIC SUNROOF Adjust the sunroof assembly forward/rearward from inside the vehicle. A plastic mallet can be used to lightly tap on the sides of the sunroof assembly to move it into the correct position. 6. Measure all 4 locations of the sunroof again to ensure they are within the specified range (12 – 14 mm). Readjust if needed. Tighten the 14 mounting nuts of the sunroof assembly when all 4 measurements are within specifications. Tightening Torque: 7. lb-ft 3 N.m 5 STUI Using STUI, take a photo of each measurement at each location of the sunroof with the last 6 digits of the VIN and the date of repair on a piece of paper. Upload the photos to STUI. 8. Install all components in the reverse order of removal. TSB #: 24-BD-002G Page 4 of 4 SUBJECT: