V0124042073713_1
Service Bulletin Details
Public Details for: V0124042073713_1
Update engine/motor control module programming for implausible evap system leak detection dtc P148D.
Models from 2019
2019 VOLKSWAGEN ATLAS |
Models from 2018
2018 VOLKSWAGEN ATLAS |
Technical Service Bulletin 01-24-04 - Update Programming DTC P148D Stored in Engine/Motor Control Module -J623- Transaction No: 2073713/1 Release date: 4/30/2024 Condition Applicable Vehicles Model(s) Year Eng. Code Trans. Code VIN Range From VIN Range To Atlas 2018-2021 3.6L All All All All All All (CDVC) Atlas Cross Sport 2020-2021 3.6L (CDVC) Revision Table Instance Number Published Date Version Number Reason For Update 2073713/1 04/30/2024 01-24-04 Original Publication The following fault code is stored in the Engine/Motor Control Module -J623- (ECM) Fault Memory: DTC Description P148D Evaporative Emission System Leak Detection Pump Implausible Frequency Do NOT diagnose or replace components due to P148D fault before performing the update function as explained in this bulletin. Page 1 of 7 Plus attachment © 2024 Volkswagen Group of America, Inc. All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher. Technical Service Bulletin 01-24-04 - Update Programming DTC P148D Stored in Engine/Motor Control Module -J623- Transaction No: 2073713/1 Release date: 4/30/2024 Technical Background Updated programming of the Engine/Motor Control Module -J623- (ECM) software is based on most recent engineering experiences and makes this knowledge available for the monitoring strategies. Production Solution Updated Engine/Motor Control Module -J623- (ECM) software introduced in Model Year 2022 Production. Service Update-Programming Procedure: Critical Warning: The VAS5908KIT battery charger must be connected to the vehicle battery for the duration of the programming, to ensure the battery state of charge remains above 12.5 volts during the update process. If the battery drops below 12.5 volts, the programming could fail which may result in damage to the control module. Control modules damaged by inadequate voltage will not be covered under the warranty policy. The technician should verify the vehicle voltage prior to starting the update process and should monitor the voltage for the duration of the update. The procedure may cancel itself if the hazard warning lights are not switched ON. The hazard warning lights prevent the system from switching to bus sleep mode during the update. ODIS-Service tester should be updated to the latest GFF technical version 24.0.1 or higher and SW version 2.49.18 or higher. Radiator Fan(s) may cycle ON high speed during the Update process! There is a risk that personal injury may result if contact is made with spinning blades. Keep hands and all objects away from the Radiator Fan(s) during the update process! Prior to launching the ODIS Service diagnostic applications and starting control module update process, confirm tester screen saver and power settings in accordance with Diagnostic Device Hardware & Windows® - VHW-22-13 Change Power Options After Windows®10 Upgrade. Failure to do so may result in the tester entering power save mode during data transfer, and subsequent control module failure. When using a VAS 6150/X or 6160/X tester in conjunction with a VAS6154A wireless transmitter head for a flash procedure, connect a USB cable between the transmitter head and the tester. Failure to do so may lead to errors during the flash procedure. VAS tools must only be used with their power adapters plugged in. Under no circumstances should they be used on battery power alone during the programming procedure Page 2 of 7 Plus attachment © 2024 Volkswagen Group of America, Inc. All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher. Technical Service Bulletin 01-24-04 - Update Programming DTC P148D Stored in Engine/Motor Control Module -J623- Transaction No: 2073713/1 Release date: 4/30/2024 To Update-Programming using Software Version Management (SVM), review and follow instructions in Technical Bulletin Instance 2014603 “Software Version Management”. The SVM process must be completed in its entirety so the database receives the update confirmation response. A warranty claim may not be reimbursed if there is no confirmation response to support the claim or action is carried out that is not explicitly stated in the Technical Bulletin. • Update the Engine Control Module using the SVM Unit code as listed in the table below: Model Engine Old Software Part No. Old Software Version New Software Part No. New Software Version (or higher) SVM Unit Code MY 18 Atlas 3.6L 03H.906.026.E 4744 03H.906.026.E 9974 4DB8 03H.906.026.F 9974 4DB8 03H.906.026.J 9974 4DB8 CDVC 6024 6695 9970 9971 9972 9973 03H.906.026.F 4745 6025 6696 9970 9971 9972 9973 03H.906.026.J 4748 6026 6697 9970 Page 3 of 7 Plus attachment © 2024 Volkswagen Group of America, Inc. All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher. Technical Service Bulletin 01-24-04 - Update Programming DTC P148D Stored in Engine/Motor Control Module -J623- Transaction No: 2073713/1 Release date: 4/30/2024 9971 9972 9973 MY 19 Atlas 3.6L 03H.906.026.R CDVC 6692 03H.906.026.R 9974 4DB8 03H.906.026.S 9974 4DB8 03H.906.026.AA 9974 4DB8 03H.906.026.AH 9977 4DB8 03H.906.026.AG 9977 4DB8 9970 9971 9972 9973 03H.906.026.S 6693 9970 9971 9972 9973 03H.906.026.AA 6694 9970 9971 9972 9973 MY20 Atlas 3.6L 03H.906.026.AH CDVC 9970 9971 9972 9973 9975 9976 03H.906.026.AG 9970 9971 9972 9973 9975 Page 4 of 7 Plus attachment © 2024 Volkswagen Group of America, Inc. All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher. Technical Service Bulletin 01-24-04 - Update Programming DTC P148D Stored in Engine/Motor Control Module -J623- Transaction No: 2073713/1 Release date: 4/30/2024 9976 03H.906.026.AF 9970 03H.906.026.AF 9977 4DB8 03H.906.026.AG 9977 4DB8 03H.906.026.AJ 3644 4DB8 03H.906.026.AJ 3644 4DB8 9971 9972 9973 9975 9976 MY20 Atlas Cross Sport 3.6L 03H.906.026.AG CDVC 9970 9971 9972 9973 9975 9976 MY21 Atlas 3.6L 03H.906.026.AJ CDVC 0454 0638 1017 1689 2666 3172 MY21 Atlas Cross Sport 3.6L 03H.906.026.AJ CDVC 1017 1689 2666 3172 The procedure can be found in GFF under Functions/ Component Selection, Software Version Management, Adapting Software. Ensure attached ECM/TCM Tuning Form has been completed and signed by customer as required in SVM Technical Bulletin Instance 2014603. Page 5 of 7 Plus attachment © 2024 Volkswagen Group of America, Inc. All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher. Technical Service Bulletin 01-24-04 - Update Programming DTC P148D Stored in Engine/Motor Control Module -J623- Transaction No: 2073713/1 Release date: 4/30/2024 Warranty To determine if this procedure is covered under Warranty, always refer to the Warranty Policies and Procedures Manual 1) Model(s) Year(s) Eng. Code(s) Trans. Code(s) VIN Range From VIN Range To Atlas 2018-2021 3.6L All All All All All All (CDVC) Atlas Cross Sport 2020-2021 3.6L (CDVC) SAGA Coding Claim Type: Use applicable Claim Type 1) Damage HST Damage Location (Depends on Service No.) -- -- Atlas / Atlas Cross Sport WWO 2) Service Number: Code 2470 0039 Parts Manufacturer Labor Operation 3) : Preparation and battery charge 01500010 = See Elsa for latest time units Labor Operation 3) : Update Programming Engine/Motor Control Module -J623- 24705599 = Actual GFF Print out, up to 50 TU max Causal Part: 24705599 Diagnostic Time 4) GFF Time expenditure 01500060 = Actual GFF print out NO Road Test 01210004 = 10 TU YES Technical Diagnosis 01320000 = 00 TU max. NO Claim Comment: Input “As per Technical Bulletin 2073713” in comment section of Warranty Claim. Page 6 of 7 Plus attachment © 2024 Volkswagen Group of America, Inc. All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher. Technical Service Bulletin 01-24-04 - Update Programming DTC P148D Stored in Engine/Motor Control Module -J623- Transaction No: 2073713/1 Release date: 4/30/2024 1) Vehicle may be outside any Warranty in which case this Technical Bulletin is informational only. 2) Code per warranty vendor code policy. 3) Labor Time Units (TUs) are subject to change with ELSA updates. 4) Documentation required per Warranty Policies and Procedures Manual. Required Parts and Tools No Special parts required. Tool Description Tool No: Battery Tester/Charger VAS5908KIT Or MTRMSP0702 battery maintainer/charger VAS Diagnostic Tool VAS 6150/X & VAS 6160/X and ODIS Service with current online updates Additional Information All part and service references provided in this Technical Bulletin are subject to change and/or removal. Always check with your Parts Dept. and Repair Manuals for the latest information. Page 7 of 7 Plus attachment © 2024 Volkswagen Group of America, Inc. All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher. OWNER INFORMATION ABOUT CONTROL MODULE TUNING* ACKNOWLEDGEMENT AND AUTHORIZATION FOR REPROGRAMMING (REFLASHING) OF CONTROL MODULE(S) *) “TUNING” is described as the addition of or modification of any component which causes a Volkswagen vehicle to perform outside the normal parameters and specifications approved by Volkswagen Group of America / Volkswagen Group Canada. Date: Dealer Number: Vehicle Identification Number: Repair Order Number: Dealer stamp I , owner or driver of the above identified Volkswagen, confirm: - “Tuning” as described above (especially power increasing modifications) has NOT been performed on my vehicle. - “Tuning” as described above has been performed on my vehicle and the following components were modified or installed: TUNING was performed by (Please provide Company name and telephone number, if you wish us to contact them): I understand that if my Control Module is determined to have been tuned, any damage caused by the tuning of the Control Module (including adverse emissions consequences) will not be covered by VWGoA / VGC warranties. I am permitting an authorized Volkswagen Dealer to reflash (update) my Control Module, and by doing so, I understand that this process will automatically overwrite (destroy) and permanently delete any tuning program that was previously installed on the Control Module of my Volkswagen vehicle. By signing below, I fully acknowledge and understand that the tuning program will not be restored and VWGoA / VGC, will not be liable in any way for the loss of tuning data. Signature of Customer E 2024 Volkswagen Group of America Inc. All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright intellectual property rights of VGoA / VGCA Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or other and by any means, .electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher.