Altec Aerial Device 2011

Vehicle Details: Recalls, Service Bulletins

Below you will find all available information on the 2011 ALTEC Aerial Device.

ManufacturerKnown WMI(s)Fuel Type
ALTEC
ALTEC VIN Decoder

Use the box here to look up VINs from ALTEC as well as other manufacturers

#
Frequently Asked Questions
  • Are there recalls for the 2011 ALTEC Aerial Device?
     - There are 12 recall(s) for the 2011 ALTEC Aerial Device, additional information is below.
NHTSA Mandated Recalls

  • Recall 255895 [USA]: A short circuit increases the risk of a fire.

  • Recall 207205 [USA]: A broken side plate may result in pedestal and truck frame separation, increasing the risk of injury.

  • Recall 188388 [USA]: Unintended movement of the lower and upper booms increases the risk of injury.

  • Recall 148142 [USA]: Loss of service brake pressure can increase the risk of a crash.

  • Recall 136862 [USA]: If the platform moves unexpectedly, it can increase the risk of injury.

  • Recall 126266 [USA]: Failure of the platform leveling yoke can cause the occupant of the platform to fall out, increasing their risk of injury.

  • Recall 139828 [USA]: The jib mast may bend and fail, increasing the risk of injury to those nearby.

  • Recall 108929 [USA]: If the aerial device is operated while the outrigger is not properly deployed it can cause instability of the boom, increasing the risk of person injury or death.

  • Recall 105842 [USA]: If the cylinder lug castings crack, they may fail, resulting in unintended movement of the boom, increasing the risk of personal injury or death to the aerial device user or those nearby.

  • Recall 109297 [USA]: In cooler temperatures, the improperly set hydraulic pressure transducer may result in inadvertent boom movement, increasing the risk of injury to the occupant or those nearby.

  • Recall 105178 [USA]: Once electrically conductive, the material is capable of melting and burning, increasing the risk of a fire.

  • Recall 64954 [USA]: The chassis batteries could short and cause a fire increasing the risk of death or serious injury.

To ensure accuracy and for your safety, it is recommended to do a free VIN recall check here or here [USA] - UK - Canada.

Recalls are also available on the Complaints page
Bulletins

Bulletins are notices put out by manufacturers in conjunction with the NHTSA to notify the public of manufacturing issues or changes.

  • SIL 3068 - EQUIPMENT: Altec has learned that certain digger derricks and aerial devices of various models built from january 2010 to january 2023 may contain access steps with a handrail and side plate that come together in a small space causing a potential pinc
  • SIL-3052 - EQUIPMENT: Altec has learned that the hydraulic ball valve on the hydraulic reservoir return line of certain l42/45 m/p units built from february 2002 to november 2019 might not get returned to the open position after being turned to the closed positi
  • PA713 - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL: Product advisory posted on our web site to inform owners, user, & operators that the new ansi a92.2-2021 standard has taken effect and they must review. The standard has changed some of the responsibilities of the parties who use or operat
  • CSR-3012 - SEAT BELTS: Altec industries, inc. Has received notification from ford motor company that a condition exists relating to motor vehicle safety, compliance, or emissions in a vehicle you possess that is equipped with altec equipment. In certain 2011
  • SIL 852 - EQUIPMENT: Altec has learned that the electrohydraulic outrigger/tools control valve on aa755l and a-series aerial devices and dlb, dmb, and d2/3/4000b series digger derricks could have the potential to produce a very small amount of flow into the low
  • No comms 2021-12 - UNKNOWN OR OTHER: There are no manufacturer communications in accordance with 49 cfr 579.5 to report for december 2021 for altec industries, inc.
  • SIL 783 - STRUCTURE: Structural cracking has been observed where the primary leveling cylinder mounting pin is welded to the lower boom side plate on ls 40/45/55 aerial devices. Failure of this connection could disable the hydraulic platform leveling system. Al
  • SIL 782 - STRUCTURE: There may be inadequate weld fusion between the boom extension cylinder rod and rod end on the affected units. This can lead to failure of the weld. Altec has developed a process to have the cylinder rod end attachment repaired by the cylin
  • SIL 764 - STRUCTURE: Altec has discovered that the protective fabric hose sock in the upper boom hose carrier on the affected units can become unsecured and slip out of place. This can expose the fiber optic lines to damage, resulting in intermittent operation
  • PUN 2020B - EQUIPMENT: Product update notice 2020b reminded customers that they may be unable to store necessary equipment in the body of the cutaway van without exceeding the rear axle capacity. For customers who are not satisfied with the remaining capacity of

© dot.report 2024

Use of this information constitutes acceptance for use in an AS IS condition. There are NO warranties, implied or otherwise, with regard to this information or its use. Any use of this information is at the user's risk. It is the responsibility of user to evaluate the accuracy, completeness or usefulness of any information, opinion, advice or other content. EACH USER WILL BE SOLELY RESPONSIBLE FOR ANY consequences of his or her direct or indirect use of this web site. ALL WARRANTIES OF ANY KIND ARE EXPRESSLY DISCLAIMED. This site will NOT BE LIABLE FOR ANY DIRECT, INDIRECT or any other kind of loss.