Bmw F-800-gs 2005
Vehicle Details: Service Bulletins
BMW VIN Decoder
Use the box here to look up VINs from BMW as well as other manufacturers
Frequently Asked Questions
-
Where is the 2005 BMW F-800-GS produced?
- The 2005 BMW F-800-GS is produced in Munich Bavaria, Germany.
NHTSA Mandated Recalls
Bulletins
Bulletins are notices put out by manufacturers in conjunction with the NHTSA to notify the public of manufacturing issues or changes.
- B611305 - ELECTRICAL SYSTEM: The electrical system of bmw vehicles has been subject to an ongoing development process over the last few years. This has led to increased demands being placed on the battery. This document covers important information for the dealer on ho
- MC55297495 - ELECTRICAL SYSTEM: Vehicle battery not charged despite the battery charger being connected to the on-board socket (manufactured before 2009)headlights and rear lights light up intermittently despite the ignition being switched off and the battery charger bein
- MC210221 - POWER TRAIN: The clutch plates do not tolerate frequent and prolonged operation at the clutch friction zone, causing a shorter service life in motorcycles that see intensive use
- B611305 - ELECTRICAL SYSTEM: Discharged battery energy diagnosis must be performed: the electrical system of bmw vehicles has been subject to an ongoing development process over the last few years. This has led to increased demands being placed on the battery. This doc
- MC1965083203 - ENGINE (PWS): Oil leaking from around the oil sump gasket.
- MC53055102 - POWER TRAIN: Gear lever does not return to neutral position. Uneven faces on shifting pawl.
- MC62332524 - POWER TRAIN: Occasionally it's not possible to downshift the transmission; especially from 3rd to 2nd gear.
- MC62133778 - EQUIPMENT: Map data should be stored on a 64 gb sd card. In garmin express the note appears that a maximum of 32 gb is possible.
- MC59759165 - ENGINE (PWS): Transmission rattles when the engine is at operating temperature and idling.
- MC6100215 - SERVICE BRAKES, HYDRAULIC: Details: bmw motorrad has ascertained that in the process of assembly, on some motorcycles even though abs connector (2) was connected to abs pressure modulator (3), retaining clip (1) is not correctly engaged in the lock (black arrow).
- SIB-63-02-01 - EXTERIOR LIGHTING: Bmw: procedure for determining and replacing incandescent and halogen light bulbs under warranty. *rm
- SIB-16-02-09 - FUEL SYSTEM, GASOLINE:DELIVERY:FUEL PUMP: Bmw vehicles: fuel level sensor repairs. Where it is necessary to replace the right or the left side fuel level sensor due to a failure, the entire pump and housing or delivery unit (suction jet assembly) do not need to be replaced as wel
- SB-00-021-07 - FUEL SYSTEM, OTHER: Bmw motorcycle: engine fuels containing ethanol. Bmw motorrad has no objection to the use of si engine fuels containing up to a maximum of 10% ethanol and imposes no warranty restrictions. Ethanol mixtures in proportions higher than 10%
- TSB-17-001-09 - ENGINE AND ENGINE COOLING:COOLING SYSTEM:HOSES/LINES/PIPING/FITTINGS: Bmw motorcycle: the coolant inlet hose is not compliant with the applicable bmw specifications. Engine operation can cause the inlet hose to widen and become correspondingly shorter; overtime this contraction in length can cause the hose to
- SB-61-003-08 - SERVICE BRAKES, HYDRAULIC:ANTILOCK/TRACTION CONTROL/ELECTRONIC LIMITED SLIP:WHEEL SPEED SENSOR: Bmw vehicles: routing abs front wheel speed sensor cable. The wiring harness front wheel speed sensor periphery plug connection is mounted on the fork cover at the bottom. *pe
- 13-003-08 - STEERING: STEERING WHEEL/HANDLE BAR: Bmw motorcycle: replacement of fuel-pressure sensor. Check of position of protective film (f-800 gs only). *pe