2008 FORD E250Ford E250 2008

Vehicle Details: Recalls, Investigations, Consumer Complaints, Decoded VIN Details, Service Bulletins

Below you will find all available information on the 2008 FORD E250.
The vehicle is described as a 4x2 Large Van-Includes van-based buses (B150-B350, Sportsman, Royal Maxiwagon, Ram, Tradesman,...).

ManufacturerKnown WMI(s)Fuel Type
FORDGasoline
FORD VIN Decoder

Use the box here to look up VINs from FORD as well as other manufacturers

#

Sub-models: - E-250 - E250 Van - E250 Cutaway - E250 Van Ffv - E250 Cutaway Chassis Cab -

Frequently Asked Questions
  • Where is the 2008 FORD E250 produced?
     - The 2008 FORD E250 is produced in Avon Lake Ohio, United States (usa).
  • Are there recalls for the 2008 FORD E250?
     - There are 18 recall(s) for the 2008 FORD E250, additional information is below.
  • What is the GVWR of a 2008 FORD E250?
     - The 2008 FORD E250 has a GVWR of Class 2G: 8,001 - 9,000 lb (3,629 - 4,082 kg) lbs.
  • How much horsepower does the 2008 FORD E250 have?
     - The 2008 FORD E250 has 255 horsepower.
NHTSA Mandated Recalls
  • Recall 131637 [USA]: If the wheelchair lift platform stops above the vehicle floor, the wheelchair user can tip inwards towards the vehicle when exiting the lift, increasing their risk of injury.

  • Recall 119853 [USA]: If the platform side plates crack or the platform mounting fails from out-of-position bearings, the lift platform can separate from the lift and come to rest against the vehicle's lift door. when the vehicle's doors are opened, the platform may fall onto the lift operator, increasing their risk of injury.

  • Recall 119601 [USA]: If the bearings move out of position, the stowed platform may have excessive movement resulting in failure of the platform mounting. this failure could cause the wheel chair lift platform to fall out of the vehicle when the doors are opened, increasing the risk of injury for the lift operator.

  • Recall 120055 [USA]: If the platform side plates crack, the lift platform can separate from the lift and come to rest against the vehicle's lift door. when the doors are opened, the platform may fall out, increasing the risk of injury to the lift operator. additionally, if the bearings move out of position, the stowed platform may have excessive movement resulting in failure of the platform mounting. this failure could cause the wheel chair lift platform to fall out of the vehicle when the doors are opened, increasing the risk of injury for the lift operator.

  • Recall 118673 [USA]: If the bearings move out of position, the stowed platform may have excessive movement resulting in failure of the platform mounting. this failure could cause the wheel chair lift platform to fall out of the vehicle when the doors are opened, increasing the risk of injury for the lift operator.

  • Recall 109204 [USA]: If the platform side plates crack, the lift platform can separate from the lift and come to rest against the vehicle's lift door. when the doors are opened, the platform may fall out, increasing the risk of injury to the lift operator.

  • Recall 97481 [USA]: If the cable does not clear the wheel chair lift it may contact the power lug and, if it does not have a nonconductive cover, or it has an improperly installed non-conductive cover, a short circuit may occur that could result in a fire.

  • Recall 94191 [USA]: A fuel leak in the presence of an ignition source may result in a fire.

  • Recall 68589 [USA]: When the platform overruns the vehicle floor level and stops at an angle from 15-20 degrees, it is possible for a person in a wheelchair to tip over and for someone standing on the platform to fall, possibly resulting in injuries.

  • Recall 80583 [USA]: The user of the lift could be injured should the lift move without the restraint belt properly buckled.

  • Recall 82746 [USA]: When the platform overruns the vehicle floor level and stops at an angle from 15-20 degrees, it is possible for a person in a wheelchair to tip over and for someone standing on the platform to fall, possibly resulting in injuries.

  • Recall 68681 [USA]: The user of the lift could be injured should the lift move without the restraint belt properly buckled.

  • Recall 83990 [USA]: This defect could result in a fire.

  • Recall 87169 [USA]: The user of the lift could be injured should the lift move unintentionally.

  • Recall 80950 [USA]: The user of the lift could be injured should the lift move unintentionally.

  • Recall 78253 [USA]: A lift occupant can be injured should the lift begin to stow unintentionally.

  • Recall 78017 [USA]: The user of the lift could be injured should the lift move unintentionally.

  • Recall 2008060 [Canada]: Other

To ensure accuracy and for your safety, it is recommended to do a free VIN recall check here or here [USA] - UK - Canada.

Bulletins

Bulletins are notices put out by manufacturers in conjunction with the NHTSA to notify the public of manufacturing issues or changes.

  • SSM 52476 - EQUIPMENT: All accessory stick-on keyless entry keypads come with a wallet card containing the master code. If the accessory keypad was factory installed, this card will be placed in the glove box and should be handed to the vehicles owner during ini
  • SSM 51909 - POWER TRAIN:AUTOMATIC TRANSMISSION: When performing any transmission fluid changes or topoffs involving mercon sp, mercon lv has replaced all versions of mercon sp and can be used going forward. Mixing mercon lv and mercon sp in the same transmission is acceptable. After 30-j
  • TSB160032 - POWER TRAIN: 4r75e transmission - grinding/whine/vibration/gear slippage - serrvice kit available
  • SSM 47009 - EQUIPMENT:ELECTRICAL: The accessory (wireless) keyless entry keypad can only be used with vehicles that are factory built with remote keyless entry (rke). The master code for the accessory (wireless) keyless entry keypad can be retrieved from fmcdealer - parts a
  • SSM 47201 - EQUIPMENT: Replacing the original equipment sync/navigation system with either an aftermarket sync/navigation kit or modifying original sync/navigation parts to provide additional features is not recommended nor supported on any ford, mercury or linco
  • TSB T2007-02 - ELECTRICAL SYSTEM:IGNITION:MODULE: On some vehicles, when the gateway 401 module transitions from its power down mode (ignition off) to its power up mode (ignition on) the module may not wake up. If this action occurs, the module's led display panels will not prove-out and t
  • 16-0032 - POWER TRAIN: 4r75e transmission - grinding/whine/vibration/gear slippage - service kit available issue a service kit has been released to assist with proper repair of the 4r75e transmission in 2008 mark lt, 2008-2010 f-150, 2008-2010 / 2013-2014 e-ser
  • TSB-14-0153 - POWER TRAIN:AUTOMATIC TRANSMISSION: Ford/lincoln/mercury: failure of planetary gear assembly is due to transmission, on certain vehicles, exhibiting grinding, gear slippage, whine type noise, vibration, while driving or loss of reverse. *pe
  • ASI-44534 - POWER TRAIN:AUTOMATIC TRANSMISSION: Ford: when shifting between park, reverse and/or during 2-3 shift, an intermittent clunk occurs with a torqshift transmission. Model 2003-2014 f-super duty, e series, excursion, f-53 motorhome chassis, low cab forward. *p
  • ASI-44538 - POWER TRAIN:AUTOMATIC TRANSMISSION: Ford/lincoln/mercury: the indicator may illuminate overdrive off and/or slipping in 3rd or no 4th gear, due to direct clutch failure and diagnostic trouble code (dtc) P0733 and/or P0734. Model 2008-2013 mark lt, f-150, crown victoria, gra
  • ASI-44404 - ENGINE AND ENGINE COOLING:ENGINE:DIESEL: Ford: on some trucks, there is a no crank situation and if voltage on transmission range sensor at pin 21, is less than 5 volts, disconnect the engine cooling fan clutch, electronically, and recheck voltage. Model 2003-2007 f super duty,
  • CSP-13B15 - TIRES: Ford: there is an increasing number of tires experiencing rapid air loss and/or tread loss, on some vans, causing tire failure and possible crash and tires need to be replaced. Model 2010-2013 e series (e-150, 250, 350, 450).
  • TSB-10-17-7 - POWER TRAIN:AUTOMATIC TRANSMISSION: Ford: there are driveability concerns such as hesitation, low idle, or loss of power. 2007-2008 e150/250. *rm
  • AS-21769 - SERVICE BRAKES, AIR:ANTILOCK: Ford: if there is an intermittent lack of power, surge, or hesitation while driving the brakes will override acceleration. *rm
  • TSB-09-20-7 - SUSPENSION:FRONT:CONTROL ARM:LOWER BALL JOINT: Ford: steering wander. Some vehicles may exhibit steering wander or free play. Steering gear mesh load adjustment. Front end alignment may be adjusted to improve the wander/free play condition. Sticky on center feel may also be due to b
Known Recall Investigations
  • Hvac switch failures investigation # EA10003

    This investigation was opened based on one complaint and reports from four transportation fleets alleging 182 blower motor control switch failures.Odi was concerned that these melting and burning switches could lead to an open flame that could spread throughout the vehicle.After a comprehensive review of all data related to overheating blower motor control switches in the subject vehicles, odi did not identify the existence of a safety defect trend.Odi reviewed 1,036 complaints, claims, and field reports of failed blower motor control switches and determined that only two fires were likely to have been caused by a failing subject blower motor control switch.This represents a failure rate of 0.2 r/100k on a population of 1,076,975 vehicles that have been in service for up to 14 years.Odi has found that when the subject switches do fail and begin to melt, they are constructed in a manner that typically prevents the failing switch from igniting and developing into an open flame.Ford motor company has agreed to take two actions to further reduce the likelihood an overheated blower motor switch in the subject vehicles.Ford informed odi that it has implemented a series of design changes to the subject switch that will help prevent it from developing internal high resistance short circuits.Ford has also informed odi that it would release a technical service bulletin (tsb-11-11-21) instructing subject vehicle owners to replace the electrical connector at the same time a failed switch is replaced.In light of the low rate of failure resulting in open flame and fire spread on the subject vehicles, and fords actions to reduce the likelihood of a switch failure through switch design changes and a tsb, further use of agency resources does not appear to be warranted.The closing of this investigation does not constitute a finding by nhtsa that no safety-related defect exists.The agency reserves the right to take further action if warranted by the circumstances.The odi complaints cited above can be reviewed at www-odi.Nhtsa.Dot.Gov/owners/searchnhtsaid under the following (odi) numbers: 10427875, 10114393, 10257890for additional information, see the attached closing report.

NHTSA decoded information from VIN

139 Results returned successfully. NOTE: Any missing decoded values should be interpreted as NHTSA does not have data on the specific variable. Missing value should NOT be interpreted as an indication that a feature or technology is unavailable for a vehicle.

Variable Value
Air Bag Loc Front1st Row (Driver and Passenger)
Body ClassCargo Van
Brake System TypeHydraulic
DisplacementCC5400.0
DisplacementCI329.52821811155
DisplacementL5.4
Drive Type4x2
Engine ConfigurationV-Shaped
Engine Cylinders8
EngineHP255
EngineKW190.1535
Error Text0 - VIN decoded clean. Check Digit (9th position) is correct
Fuel Type PrimaryGasoline
GVWRClass 2G: 8,001 - 9,000 lb (3,629 - 4,082 kg)
MakeFORD
MakeID460
ManufacturerFORD MOTOR COMPANY, USA
Manufacturer Id976
ModelE-250
ModelID1817
Model Year2008
NCSA Body TypeLarge Van-Includes van-based buses (B150-B350, Sportsman, Royal Maxiwagon, Ram, Tradesman,...)
NCSA MakeFord
NCSA ModelE-Series Van/Econoline
Other Engine InfoEFI
Other Restraint System InfoSec. Gen. Air Bags
Plant CityAVON LAKE
Plant Company NameOhio Assebly Plant
Plant CountryUNITED STATES (USA)
Plant StateOHIO
Seat Belts AllManual
SeriesEconoline
VIN1FTNE24L28DB10110
Vehicle TypeTRUCK
Most Recent Consumer Complaints and Accidents
CrashFireTowedInjuredDeathsFailure
Date
NoNoN NoneNone20201228

Thankfully i was driving slowly between curves on a stretch of roadway with a 30mph speed limit (one lane each direction) when i 'blew a spark plug'. The coil was also damaged i was told. I was also told there's no guarantee that it would never happen again, and i have 7 other spark plugs and coils in the engine, so expect it. Allegedly 3 were replaced just before we bought this used in 2016. I tried to get receipts for vehicle maintenance records, but the shop refused and the private owner had moved and thrown her paperwork away. This was in massachusetts. I had no warning, that i know of. Suddenly there was a loud bang and a repeated bang, bang, bang! I pulled over immediately. (thankfully it wasn't a 3 or more lane highway with my mother in her wheelchair!) the banging only stopped when the engine was off. I was unable to look at the engine compartment with the van on because i was afraid of more damage! It was put on a flatbed and towed by aaa, to a shop a few miles away. Unfortunately, this shop couldn't get it inside to work on. A friend of mine did the repair in the parking lot. ***apparently this is a very frequent problem with these ford e250 engines. There is a lot of people experiencing the same problem. I had no idea! It could be extremely dangerous on a multi lane highway, traveling at high speeds, going up and down the mountains (i travel between nys & massachusetts), in subzero temperatures especially with someone in a wheelchair onboard!*** i have no receipts. Aaa of central ny should have a record of the tow.

NoNoN NoneNone20201227

Thankfully i was driving slowly between curves on a stretch of roadway with a 30mph speed limit (one lane each direction) when i 'blew a spark plug'. The coil was also damaged i was told. I was also told there's no guarantee that it would never happen again, and i have 7 other spark plugs and coils in the engine, so expect it. Allegedly 3 were replaced just before we bought this used in 2016. I tried to get receipts for vehicle maintenance records, but the shop refused and the private owner had moved and thrown her paperwork away. This was in massachusetts. I had no warning, that i know of. Suddenly there was a loud bang and a repeated bang, bang, bang! I pulled over immediately. (thankfully it wasn't a 3 or more lane highway with my mother in her wheelchair!) the banging only stopped when the engine was off. I was unable to look at the engine compartment with the van on because i was afraid of more damage! It was put on a flatbed and towed by aaa, to a shop a few miles away. Unfortunately, this shop couldn't get it inside to work on. A friend of mine did the repair in the parking lot. ***apparently this is a very frequent problem with these ford e250 engines. There is a lot of people experiencing the same problem. I had no idea! It could be extremely dangerous on a multi lane highway, traveling at high speeds, going up and down the mountains (i travel between nys & massachusetts), in subzero temperatures especially with someone in a wheelchair onboard!*** i have no receipts. Aaa of central ny should have a record of the tow.

NoNoN NoneNone20170228

My transmission went about two weeks ago. I was told that ford had bad transmissions in the years of my van, by the mechanic. Then friday night i was driving along and the van started acting funny, not accelerating and a wrench light came on. Then a little engine light came on and my car died. I got it to go about 30mph on the expressway and got it to the garage. :[ i looked up what happened and found out that the throttle body problem is common in the ford, just not the e250. But it is the same problem as the escape, so obviously a ford problem!! I have already put in a new transmission and now this. I feel that these things should not go after only 9 years. This vehicle is for transporting my two boys in wheelchairs with a muscle disease. I need my car!!! But i am going broke! If these problems are ford and you are fixing them for free within ten years, then that is what you should do! [xxx]. [xxx] information redacted pursuant to the freedom of information act (foia), 5 u.S.C. 552(b)(6). *tr

CrashNoN 1 InjuredNone20130717

I was driving in the rain going 45 and as i was heading downhill i attempted to slow down. The vehicle began to hydroplane and i could not control the direction i was going. I ran front first into a guardrail and my van flipped over and rolled. The air bags never deployed and the vehicle was totaled. *tr

CrashNoN 1 InjuredNone20090724

When the engine on the 2008 e250 ford cargo van was started and the truck put into the drive gear, the engine raced at a high rpm rate sufficient to spin the rear wheels, lunge forward under what felt like full power, slammed through a fence and down into a ravine. The van was a rental from enterprise leasing co. The passenger's right ring finger was severed in the crash. No air bags deployed and apparently never installed in the 2008 van. The accelerator appeared to be stuck in the out-of-control run-away. *tr

Common OBD-II Error Codes
  • P0733 [1] Gear 3 Incorrect ratio
  • P0734 [1] Gear 4 Incorrect ratio
Latest VINs Decoded for this Manufacturer
VIN Year Model Manufactured In
1FTNE24L28DB101102008E-250AVON LAKE OHIO, UNITED STATES (USA)
1FTNE24W28DB496002008E-250AVON LAKE OHIO, UNITED STATES (USA)
1FTNE24W58DA033222008E-250AVON LAKE OHIO, UNITED STATES (USA)
1FTNE24W78DB216292008E-250AVON LAKE OHIO, UNITED STATES (USA)
1FTNS24W08DA013112008E-250AVON LAKE OHIO, UNITED STATES (USA)
1FTNE24W78DA445662008E-250AVON LAKE OHIO, UNITED STATES (USA)
1FTNS24W98DA724882008E-250AVON LAKE OHIO, UNITED STATES (USA)
1FTNE24L98DA733322008E-250AVON LAKE OHIO, UNITED STATES (USA)
1FTNE24LX8DA830582008E-250AVON LAKE OHIO, UNITED STATES (USA)
1FTNE24W48DB028612008E-250AVON LAKE OHIO, UNITED STATES (USA)
1FTNE24L28DA789542008E-250AVON LAKE OHIO, UNITED STATES (USA)
1FTNS24W18DA283412008E-250AVON LAKE OHIO, UNITED STATES (USA)
1FTNE24W48DA714512008E-250AVON LAKE OHIO, UNITED STATES (USA)
1FTNS24WX8DB535022008E-250AVON LAKE OHIO, UNITED STATES (USA)
1FTNS24W08DA839142008E-250AVON LAKE OHIO, UNITED STATES (USA)
1FTNE24W08DA841502008E-250AVON LAKE OHIO, UNITED STATES (USA)
1FTNE24LX8DB552462008E-250AVON LAKE OHIO, UNITED STATES (USA)
1FTNE24L58DB046902008E-250AVON LAKE OHIO, UNITED STATES (USA)
1FTNE24W68DA556552008E-250AVON LAKE OHIO, UNITED STATES (USA)
1FTNE24W68DA028122008E-250AVON LAKE OHIO, UNITED STATES (USA)
1FTNE24W98DA996482008E-250AVON LAKE OHIO, UNITED STATES (USA)
1FTNE24W98DA174202008E-250AVON LAKE OHIO, UNITED STATES (USA)
1FTNE24W28DA904352008E-250AVON LAKE OHIO, UNITED STATES (USA)
1FTNS24W38DB137292008E-250AVON LAKE OHIO, UNITED STATES (USA)

© dot.report 2024

Use of this information constitutes acceptance for use in an AS IS condition. There are NO warranties, implied or otherwise, with regard to this information or its use. Any use of this information is at the user's risk. It is the responsibility of user to evaluate the accuracy, completeness or usefulness of any information, opinion, advice or other content. EACH USER WILL BE SOLELY RESPONSIBLE FOR ANY consequences of his or her direct or indirect use of this web site. ALL WARRANTIES OF ANY KIND ARE EXPRESSLY DISCLAIMED. This site will NOT BE LIABLE FOR ANY DIRECT, INDIRECT or any other kind of loss.