Hino Nj8j 2013
Vehicle Details: Recalls, Service Bulletins
Below you will find all available information on the 2013 HINO Nj8j.
| Manufacturer | Known WMI(s) | Fuel Type |
|---|---|---|
| HINO |
HINO VIN Decoder
Use the box here to look up VINs from HINO as well as other manufacturers
Frequently Asked Questions
-
Are there recalls for the 2013 HINO Nj8j?
- There are 3 recall(s) for the 2013 HINO Nj8j, additional information is below.
NHTSA Mandated Recalls
Recall 128444 [USA]: If the vehicle pulls left, it may cross into another lane unexpectedly, increasing the risk of crash.
Recall 92183 [USA]: If the b+ circuit shorts to ground, it may lead to a fire.
Recall 2013464 [Canada]: Steering
To ensure accuracy and for your safety, it is recommended to do a free VIN recall check here or here [USA] - UK - Canada.
Bulletins
Bulletins are notices put out by manufacturers in conjunction with the NHTSA to notify the public of manufacturing issues or changes.
- TT-14-033 - EQUIPMENT: When replacing an engine block with service part no., 11401e0380 there is potential that 2 rear oil passage plugs may be missing in the rear of the replacement engine block. In the event your replacement engine block does not have these 2 o
- TT-14-017 - EQUIPMENT: Bendix? Air dryer service
- TT-14-016 - ENGINE AND ENGINE COOLING:EXHAUST SYSTEM: Exhaust combustion chamber with loose insulation
- SB-14-020 - EQUIPMENT ADAPTIVE/MOBILITY: When replacing a broken hood grille, an enhanced replacement hood grille is available. This procedure should be used when installing this enhanced grille to make certain that the hood grille is correctly installed.
- SB-14-016 - SERVICE BRAKES, HYDRAULIC:ANTILOCK/TRACTION CONTROL/ELECTRONIC LIMITED SLIP:ABS WARNING LIGHT: In the event that one of the subject vehicles is driven while the abs warning lamp is illuminated, operation of the torque converter clutch will be suspended. Driving the vehicle with an abs warning lamp illuminated can lead to overheating
- SB-14-014 - EQUIPMENT: Subject vehicles may exhibit a concern where manual regeneration does not complete within one hour of depressing the manual regeneration button. In these cases, there will be no indicators showing why manual regeneration will not complete.
- SB-14-013 - ENGINE AND ENGINE COOLING:EXHAUST SYSTEM: Dpr damage, "burner misfire due to excessive soot on the burner igniter surface", and "dpr push out" may occur due to the increase in the amount of soot in exhaust gas as a result of engine component degradation. In order to reduce the soot
- 14-002 - ELECTRICAL SYSTEM: Coe hybrid safety equipment, tools and practices
- TSB-14-025 - ELECTRICAL SYSTEM: Subject vehicles may exhibit electrical symptoms which can include, but are not limited to erratic operation of the exterior lamps, warning lamps illuminated in the instrument cluster, or erroneous dtc?S (diagnostic trouble codes) setting i
- SB-15-010 - EQUIPMENT: Some vehicles that operate in extreme cold weather climates may exhibit ice accumulation on the egr (exhaust gas recirculation) butterfly plate with a repeat P1604 dtc (diagnostic trouble code) stored in the engine ecu. A heated egr valve h
- HINO 12-002 TT - FUEL SYSTEM, GASOLINE: Some engines may erroneously record a P202E dtc in the dcu along with a P204F in the ecu. This fault condition is due to dcu software misdetection of def system pressure being delivered to the def injector.
- 167-B1904-01 - SERVICE BRAKES, HYDRAULIC: Sa-19-011 aacl0 conventional alp drum and dust shield procedure changes
- 167-T1514-12 - STRUCTURE:BODY: Tt-15-016 the purpose of this publication is to communicate the standard measuring positions on the hino chassis. In some cases, the customer may report a visual chassis posture concern where the chassis appears to be leaning more towards t
- 167-T1513-12 - POWER TRAIN: Tt-15-014 the transmission dtc?S P0974 and P0986, may be found on 12my-15my coe models. There could also be a complaint of low power and erratic shifting. These diagnostic codes may be set due to low voltage between the transmission case an
- 167-T0706-12 - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : 07 - 006 voltage drop test
- 167-B1312-12 - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : Sb-13-009 this bulletin is to inform dealers and workshops of proper paint codes for all hino models. All models
- 167-B1307-12 - POWER TRAIN:AUTOMATIC TRANSMISSION:GEAR POSITION INDICATION (PRNDL): 13-008 design change of the idler gear case and idler gear bolt. Abnormal load such as a stuck supply pump was applied to gear train then causing the bolt to loosen. Therefore, an enhancement to the case and bolt were carried out. The idle
- 167-B1302-12 - POWER TRAIN:DRIVELINE:DIFFERENTIAL UNIT: Sb -13 - 001 incorrect rear axle differential fluid. Certain rear drive axles were improperly filled with non-synthetic differential fluid during assembly at the wv assembly plant instead of the intended full synthetic differential fluid.
- 167-B1625-12 - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : Sb-16-021 correction of workshop manual for hino600 series correction of electrical wiring diagram
- 167-B1621-12 - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : Sb-16-010 correction of the inspection of the dpr filter.
- 167-T1415-12 - ENGINE AND ENGINE COOLING:EXHAUST SYSTEM: Tt-14-016 during service of the exhaust aftertreatment system, the technician may visually find that the insulation within the outer shell of the combustion chamber is pushing out or loose. In the event that loose insulation is found, it is
- 167-B1529-12 - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : Sb-15-032 troubleshooting information and inspection procedure of the dtc/P2030 were revised.
- 167-B1528-12 - EQUIPMENT:ELECTRICAL: Sb-15-031 foreign debris in the def (diesel exhaust fluid) tank may cause the scr (selective catalyst reduction) system to malfunction. This can result in dtc?S (diagnostic trouble codes) P20E8 or P20E9 - def pressure abnormality. An inlet
- 167-B1523-12 - ENGINE AND ENGINE COOLING: Sb-15-026 a subject vehicle may exhibit an engine oil leak or engine coolant leaking externally from the engine head gasket sealing area on the exhaust manifold side of the engine. An improved head gasket has been made available as a servic
- 167-B1521-12 - SUSPENSION: Sb-15-022 in the rare event that a subject vehicle equipped with the 23k comfort ride air suspension experiences a premature main leaf failure, a 23k hd comfort ride air suspension may be installed with prior approval from hmm qa.
- 167-B1515-12 - ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:MANIFOLD/HEADER/MUFFLER/TAIL PIPE: Sb-15-016 new parts are available to prevent repeat exhaust manifold stud failures on the j05 engine. This bulletin provides instructions for installing longer manifold studs at the #4 cylinder location.
- 167-B1511-12 - STEERING: STEERING WHEEL/HANDLE BAR: Sb-15-011 the following tsb (technical service bulletin) outlines the inspection method for steering wheel free play and the adjustment procedure of the steering gear.
- 167-B1510-12 - ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:GAS RECIRCULATION VALVE (EGR VALVE): Sb-15-010 some vehicles that operate in extreme cold weather climates may exhibit ice accumulation on the egr (exhaust gas recirculation) butterfly plate with a repeat P1604 dtc (diagnostic trouble code) stored in the engine ecu. A heated e
- 167-B1504-12 - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : Sb-15-003 correction of workshop manual for hino 2015my (revision of troubleshooting procedure for the dtc P0421)
- 167-B1503-12 - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : Sb-15-002 correction of workshop manual for 2013 - 2015my (revision of troubleshooting procedure for the dtc P2123)
- 167-B1415-12 - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : Sb-14-003 the following is to inform you of the revision of the inspection procedure for the dtc?S P0340 and P0341. You are kindly requested to attach this service data to the relevant pages of the workshop manuals for maintenance and to us
- 167-B1426-12 - STRUCTURE:BODY:HOOD:HINGE AND ATTACHMENTS: Sa-14-026 the broken hood grille procedure (sb-14-020) has been revised to reuse the grille nuts (sz17906009) if possible. There is a limited quantity of the nuts available and it has been confirmed that the nuts are reusable. The revised p
- 167-B1423-12 - EQUIPMENT:ELECTRICAL: Sb-14-005 2011my-2015my conventional keyless entry programming
- 167-B1423-12 - ELECTRICAL SYSTEM:SOFTWARE: Sb-14-005 2011my-2015my conventional keyless entry programming
- 167-T1303-12 - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : 13-003 injection quantity test 11 thru 14my
- 167-T1203-12 - ENGINE AND ENGINE COOLING: 12 - 002 diagnosis procedure for P202E (dcu) associated with P204F (ecu) some engines may erroneously record a P202E dtc in the dcu along with a P204F in the ecu. This fault condition is due to dcu software misdetection of def system pressu
- 167-T1202-12 - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : 12-001 recording the burner event log (bel) on 11-13my trucks
- 167-B0803-12 - WHEELS:LUGS/NUTS/BOLTS/STUDS: Sb - 08 - 005 this document is to inform dealers and workshops of the design change to the hood damper, support bolt and the addition of a support collar.
- 167-B0602-12 - ENGINE AND ENGINE COOLING:ENGINE:OTHER FUEL TYPES:TURBO/SUPERCHARGER: Sb ? 06 - 002 fuel filter usage. This bulletin provides technical information for proper fuel filter usage as well as an example of damage caused by foreign material allowed to enter the fuel system as a result of using an improper fuel fil
- 167-B0601-12 - ENGINE AND ENGINE COOLING: Sb ? 06 - 001 design change of engine oil cooler housing. The casting for the engine oil cooler housing has been revised to include 2 shallow machined grooves on both sides of the engine oil cooler housing. These grooves aid in the retentio
- 167-B0508-12 - POWER TRAIN:AXLE ASSEMBLY: Sb - 05 - 005 proper maintenance procedures for grease lubricated front axles
- 167-B0506-12 - ENGINE (PWS): Sb ? 05 - 008 this document is to inform the dealers about the addition of the pressure sensor cover and related part for the j08e engine.
- 167-B0505-12 - EQUIPMENT ADAPTIVE/MOBILITY: Sb ? 05 - 007 design change of water pipe for j08e
- 167-B0504-12 - ENGINE AND ENGINE COOLING:EXHAUST SYSTEM: Sb - 05 - 003 this document is to inform dealers and workshops on procedures to activate exhaust brake operation.
- 167-B0503-12 - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : Sb ? 05 - 010 correction to workshop manuals for the j08e engine. A) resistance between terminals of the air intake pre-heater relay should be 64.0 ? 96.0 ohms b) illustration of the air intake pre-heater terminal should be revised. C) r
- 167-B0502-12 - TIRES: Sb - 05 - 004 speedometer recalibration. This document is to inform of the procedure to calibrate the pulse adjust module whenneeded (ex. Tire size change, rear carrier ratio change).
- 167-B0501-12 - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : 05 - 011 corrections to workshop manuals for j08 engines. The standard gap between ends of the second piston ring and the oil ring.
- 167-R1306-12 - ENGINE (PWS): Sb -13 - 001 certain rear drive axles were improperly filled with non-synthetic differential fluid during assembly at the wv assembly plant instead of the intended full synthetic differential fluid. The non-synthetic differential fluid must
- 167-P1602-12 - FUEL SYSTEM, GASOLINE:DELIVERY:FUEL PUMP: 13-008 injection pump drive case. Please note the following part number changes to the injection pump bearing case. Not replacing the correct replacement parts will result in major engine damage. The hino ordering system has been modified
- RCB-001-13 - ENGINE AND ENGINE COOLING:ENGINE:DIESEL: Hino: soot accumulates on the igniter. Burner ignition could perform improperly. Replacement of the diesel particulate regeneration (dpr) igniter plugs. *kb
- RCB-009-12 - ELECTRICAL SYSTEM:SOFTWARE: Hino: software update for burner control unit (bcu). Ignition of the burner system may perform improperly and cause a mil light to illuminate in the instrument cluster. *kb
- RCB-002-13 - ELECTRICAL SYSTEM:SOFTWARE: Hino trucks: malfunction indicator lamp (mil) may be illuminating. Vehicle may also experience reduced power. Performing a software enhancement should correct this problem. *kb