Nova Bus Nova Lfs 2010

Vehicle Details: Recalls, Service Bulletins

Below you will find all available information on the 2010 NOVA BUS Nova Lfs.

ManufacturerKnown WMI(s)Fuel Type
NOVA BUS
NOVA BUS VIN Decoder

Use the box here to look up VINs from NOVA BUS as well as other manufacturers

#
Frequently Asked Questions
  • Are there recalls for the 2010 NOVA BUS Nova Lfs?
     - There are 35 recall(s) for the 2010 NOVA BUS Nova Lfs, additional information is below.
NHTSA Mandated Recalls
  • Recall 246951 [USA]: The colorful lighting may cause confusion by distracting other drivers, increasing the risk of a crash.

  • Recall 211448 [USA]: Reduced visibility of the brake and tail lights can increase the risk of a crash.

  • Recall 115739 [USA]: If the seat belt anchorage assembly separates from the j-bracket, the bus driver may not be properly restrained in the event of a crash increasing their risk of injury.

  • Recall 108992 [USA]: A passenger could be injured if their arm is caught in the door.

  • Recall 107713 [USA]: If the axle half shaft fails, the bus would be disabled, increasing the risk of a crash.

  • Recall 104353 [USA]: If the abs malfunction light does not illuminate if the abs control unit loses power, the driver would not be aware that the abs is not functional and that the brakes may unexpectedly lock up under certain conditions when the brakes are applied, increasing the risk of crash.

  • Recall 104377 [USA]: Arcing of the alternator cable may result in an engine compartment fire.

  • Recall 100806 [USA]: Once electrically conductive, the material is capable of melting and burning, increasing the risk of a fire.

  • Recall 91896 [USA]: In the event the egress window fails during an emergency situation, passengers may be trapped in the bus placing them at risk of injury.

  • Recall 94717 [USA]: If the inlet or outlet sections disconnect, hot exhaust gases can vent prior to exiting the tailpipe, creating the risk of combustion and a fire. if both clamps fail, there is a risk in some applications that the doc/dpf housing may detach completely, creating a road hazard.

  • Recall 82056 [USA]: The vehicle may move inadvertently even when the parking brake is applied increasing the risk of a crash.

  • Recall 82512 [USA]: The bolts can be worn prematurely and break off, increasing the risk of a crash.

  • Recall 84752 [USA]: Deterioration of these o-rings may occur and leaking or seepage of hydraulic oil.

  • Recall 86871 [USA]: The manufacturer has not yet provided a consequence for this campaign.

  • Recall 2021128 [Canada]: Lights and instruments

  • Recall 2018456 [Canada]: Seats and restraints

  • Recall 2016144 [Canada]: Seats and restraints

  • Recall 2015065 [Canada]: Powertrain

  • Recall 2014545 [Canada]: Seats and restraints

  • Recall 2014263 [Canada]: Electrical

  • Recall 2014262 [Canada]: Brakes

  • Recall 2013412 [Canada]: Electrical

  • Recall 2012393 [Canada]: Other

  • Recall 2012206 [Canada]: Brakes

  • Recall 2011398 [Canada]: Steering

  • Recall 2011381 [Canada]: Engine

  • Recall 2011110 [Canada]: Steering

  • Recall 2010021 [Canada]: Engine

  • Recall 2010048 [Canada]: Other

  • Recall 2010065 [Canada]: Fuel supply

  • Recall 2010226 [Canada]: Brakes

  • Recall 2010311 [Canada]: Steering

  • Recall 2010389 [Canada]: Engine

  • Recall 2009253 [Canada]: Steering

  • Recall 2022248 [Canada]: Lights and instruments

To ensure accuracy and for your safety, it is recommended to do a free VIN recall check here or here [USA] - UK - Canada.

Bulletins

Bulletins are notices put out by manufacturers in conjunction with the NHTSA to notify the public of manufacturing issues or changes.

  • LI5170E - SUSPENSION: New lower shock mount available with an adapter plate better suited for the front and rear axle.
  • LI5178R1 - SERVICE BRAKES, HYDRAULIC: Installation of new pressure regulator for retarder interlock. Obsolete part replacement
  • LI3978E - ENGINE AND ENGINE COOLING: Information about the engine coolant. Coolant types should not be mixed in the engine.
  • LI5011E - EQUIPMENT: Recommendations on the disinfection of vehicles as well as products and precautions to be taken.
  • LI4955E - FUEL SYSTEM, OTHER:FUEL FILTER: The auxiliary heater fuel filter is now obsolete. The fuel filter and its support will have to be replaced at its next maintenance.
  • LI4696ER1 - EQUIPMENT: Auxiliary heater thermo 300 is discontinued. The thermo plus unit will replace the current unit only if the whole unit needs to be replaced. There is no need to retrofit any buses with the new thermo plus units. Replacement parts are availa
  • LI4432ER1 - STEERING: Trw has eliminated from service procedure tas-103 the greasing of the steering gearbox output shaft.
  • APS4896E - EQUIPMENT ADAPTIVE/MOBILITY: Introduction of a new steering gearbox without the lubrication zerk.
  • LI4577ER1 - EQUIPMENT: The repair kit parts will require a specific installation procedure. Current stock parts may still be used
  • APS4531E - EQUIPMENT: Availability of a dust protection kit to remove the maintenance need to clean the flame sensor sight glass when excessive soot or debris is accumulated on the internal burner head disc.
  • LI4546E - UNKNOWN OR OTHER: To avoid the risk of air being trapped which could damage the egr cooler.
  • LI4512E - BRAKES (PWS): Brake wear signal reads 0% or fluctuates
  • LI4396E - ENGINE (PWS): An inadequate assembly sequence of the engine cradle may cause cracks in certain cases.
  • LI3994ER1 - ENGINE AND ENGINE COOLING: N41269 pal hydraulic filter head discontinued and replaced by hydraulic filter head n8905938 and filter n8905939
  • LI4083E - EQUIPMENT: N64662 pal hydraulic filter head discontinued and replaced by hydraulic filter head n8905938 and filter n8905939
  • LI4059ER1 - STRUCTURE: In case of replacing the existing radiator, there is an option to either refit the radiator to the existing frame or replace the complete radiator assembly with frame.
  • LI3402ER3 - ENGINE AND ENGINE COOLING:COOLING SYSTEM: Low coolant level sensor warning
  • BS4051ER3 - BRAKES (PWS): Interlock brake is activated when the b-bus network is disconnected or lost.
  • LI3188 - SUSPENSION: A new radius rod bolt torque is now in effect.
  • LI3191 - ELECTRICAL SYSTEM:SOFTWARE: A new procedure is available to reprogram a new io/a or io/b without a laptop
  • APS3176 - ELECTRICAL SYSTEM:ALTERNATOR/GENERATOR/REGULATOR: Alternator in load signal may cause malfunction of io/b v-bea module
  • BS3070 - SERVICE BRAKES, AIR:SUPPLY:HOSES, LINES/PIPING, AND FITTINGS: Possible chafing between the brake hoses and surrounding components.
  • BS3148 - ENGINE AND ENGINE COOLING: Ventilate the engine compartment
  • LI3193 - LATCHES/LOCKS/LINKAGES:HOOD:LATCH: The rear engine access door may not close properly
  • BS3192E - ENGINE AND ENGINE COOLING:EXHAUST SYSTEM: Exhaust system flexible joint bellows, isl10 engine: the flexible joint bellows may be deformed
  • BS1783ER2 - EQUIPMENT ADAPTIVE/MOBILITY: Bolts could become loose, which could cause the seat to drop.
  • BS1783ER1 - EQUIPMENT ADAPTIVE/MOBILITY: Bolts could become loose, which could cause the seat to drop.
  • LI2116E - SERVICE BRAKES, AIR:DISC: Diagnose a potentiel bendix disk brake thermal overload.
  • LI1995ER2 - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : Modifications to the fuel tank warranty
  • LI3129E - EQUIPMENT ADAPTIVE/MOBILITY: Exterior speaker may stop working.
  • APS3277 - ENGINE (PWS): Cummins engine code 584. Prevent unjustified logging of starter lockout code.
  • LI1846E - EQUIPMENT ADAPTIVE/MOBILITY: New procedure for the radiator assembly anchorage levelling to optimize the filling of the coolant and surge tank cap n36242 replaced by n65114
  • BS2030A - EQUIPMENT ADAPTIVE/MOBILITY: Rubber support breaks on the horizontal cac pipe.
  • BS1592AR1 - EQUIPMENT ADAPTIVE/MOBILITY: Rubber support breaks on the horizontal cac pipe.
  • LI1995ER1 - EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL : Modifications to the fuel tank warranty
  • BS1908ER1 - ENGINE (PWS): The engine air intake hose could rub against the air conditioning compressor components
  • BS1908E - ENGINE (PWS): The engine air intake hose could rub against the air conditioning compressor components
  • LI3402ER1 - ENGINE AND ENGINE COOLING: Low coolant level sensor warning
  • LI3402ER2 - ENGINE AND ENGINE COOLING: Low coolant level sensor warning
  • BS3419E - VISIBILITY:WINDSHIELD WIPER/WASHER:MOTOR: The wiper motor cannot be stopped by the driver.
  • BS3359ER2 - ENGINE (PWS): Cummins isl10 engine does not have the configuration to support fault code 2448.
  • BS3239ER2 - ENGINE AND ENGINE COOLING:COOLING SYSTEM:RADIATOR ASSEMBLY: Coolant filling of the radiator surge tank might be erratic and create air pockets.
  • APS3429E - ELECTRICAL SYSTEM:12V/24V/48V BATTERY: Terminal lugs of the battery cables may crack due to stress.
  • LI3732ER1 - EQUIPMENT ADAPTIVE/MOBILITY: Procedure to follow when replacing a plastic motorize valve by a metal motorize valve.
  • BS4051ER2 - PARKING BRAKE: Interlock brake is activated when the b-bus network is disconnected or lost.
  • LI2068E - EQUIPMENT ADAPTIVE/MOBILITY: Risk of oil leaks, particularly in hot climates, o-rings on zf axle type av-132
  • BS1818ER1 - ENGINE AND ENGINE COOLING:COOLING SYSTEM:HOSES/LINES/PIPING/FITTINGS: Coolant fluid hoses for the def reservoir may come into contact with the engine cradle and the streetside engine support, close to the transmission. In cases of contact, tearing of the hoses could result.
  • BS4051E - BRAKES (PWS): Interlock brake is activated when the b-bus network is disconnected or lost
  • LI3948E - SERVICE BRAKES, AIR:ANTILOCK: In case of replacing the existing zf abs sensor of av-132, there is an option to refit the abs sensor in accordance with av-132 ii
  • BS1906E - EQUIPMENT ADAPTIVE/MOBILITY: A break may occur between the mounting plate and the stanchion.
  • BS1800ER1 - SEATS: Seat retainer clips break due to repeated removal of bench for engine access.
  • BS1800E - SEATS: Seat retainer clips break due to repeated removal of bench for engine access.
  • LI1841ER3 - EXTERIOR LIGHTING:HEADLIGHTS: Repair procedure of the front beam box
  • BS1901ER1 - EQUIPMENT ADAPTIVE/MOBILITY: Cancelling document for mounting bolts become loose in service,fuel tank mounting bolts
  • BS1901E - EQUIPMENT ADAPTIVE/MOBILITY: Mounting bolts become loose in service,fuel tank mounting bolts
  • BS1742ER1 - SERVICE BRAKES, AIR:ANTILOCK:ABS WARNING LIGHT: Possible chaffing between brake hoses and surrounding components, possibly causing the loss of abs sensor signal.
  • BS1905ER1 - ELECTRICAL SYSTEM: Corrosion may create poor electrical conductivity. Excessive current passing through the main disconnect switch may lead to the failure of the pdb.
  • BS1742ER2 - SERVICE BRAKES, AIR:ANTILOCK:ABS WARNING LIGHT: Possible chaffing between brake hoses and surrounding components, possibly causing the loss of abs sensor signal.
  • BS2036ER1 - EQUIPMENT ADAPTIVE/MOBILITY: Abnormal delay in retarder application
  • BS2036E - EQUIPMENT ADAPTIVE/MOBILITY: Abnormal delay in retarder application
  • LI3061E - ENGINE AND ENGINE COOLING:COOLING SYSTEM:HOSES/LINES/PIPING/FITTINGS: Eliminate the overheating of the dosage module by adding an extension to the cooling hose to maintain the supply of cooling liquid to the dosing valve.
  • BS1876ER1 - POWER TRAIN: Zf differential thrust washer failure
  • LI3753E - STRUCTURE:FRAME AND MEMBERS: Vertical beam might crack above front door, second post capping.
  • LI1911ER1 - EQUIPMENT ADAPTIVE/MOBILITY: Zf wheel head suspension. Zf introduced an optimized axial roller bearing. Replace the axial roller bearing and lower seal ring with an optimized roller bearing.
  • BS3047ER1 - ELECTRICAL SYSTEM: N22759 protective cable sheathing. The protective sheathing may be damaged and cause error codes on the diagnostic network.
  • LI3187 - STEERING:HYDRAULIC POWER ASSIST:HOSE, PIPING, AND CONNECTIONS: The power steering hydraulic lines may be loose in the radiator compartment
  • BS3186E - SUSPENSION:FRONT: Radius rod bolts may come loose
  • BS3510e - ENGINE (PWS): Sensor supply (tps2) cable replacement. Cummins code 1242 for accelerator interlock circuit
  • bs3270e - EQUIPMENT: Unable to perform stationary regeneration.
  • bs3310er2 - EQUIPMENT ADAPTIVE/MOBILITY: Cummins code 1242 for accelerator interlock circuit
  • BS3239E - ENGINE AND ENGINE COOLING:COOLING SYSTEM:RADIATOR ASSEMBLY: Coolant filling of the radiator surge tank might be erratic and create air pockets.
  • BS3147E - EQUIPMENT ADAPTIVE/MOBILITY: Aic module records noise error codes.
  • BS3282E - EQUIPMENT ADAPTIVE/MOBILITY: A/c compressor belts may split down the center.
  • LI1643ER1 - EQUIPMENT ADAPTIVE/MOBILITY: The crystallization of urea creates leaks and venting odors, and dirt may enter the reservoir.
  • BS3239ER1 - ENGINE AND ENGINE COOLING:COOLING SYSTEM:RADIATOR ASSEMBLY: Coolant filling of the radiator surge tank might be erratic and create air pockets. Document ''on hold'' waiting for the next revision.
  • BS3239E - ENGINE AND ENGINE COOLING:COOLING SYSTEM:RADIATOR ASSEMBLY: Coolant filling of the radiator surge tank might be erratic and create air pockets.
  • BS3147E - EQUIPMENT ADAPTIVE/MOBILITY: Aic module records noise error codes.
  • BS3282E - EQUIPMENT:APPLIANCE:AIR CONDITIONER: A/c compressor belts may split down the center.
  • LI1643ER1 - EQUIPMENT: The crystallization of urea creates leaks and venting odors, and dirt may enter the reservoir.
  • BS3334E - EQUIPMENT ADAPTIVE/MOBILITY: The skinner valve of the interlock may trigger on code in the clever device
  • BS3369E - ELECTRICAL SYSTEM: The starter may damaged the ring gear.
  • BS3362E - ENGINE AND ENGINE COOLING:COOLING SYSTEM:RADIATOR ASSEMBLY: Coolant filling of the radiator surge tank might be erratic and create air pockets
  • BS3359E - ENGINE (PWS): Cummins isl10 engine does not have the confi guration to support fault code 2448
  • BS3225E - ENGINE AND ENGINE COOLING:COOLING SYSTEM: Coolant leak near engine thermostat
  • BS3223E - EQUIPMENT:APPLIANCE:AIR CONDITIONER: The engine air intake hose could rub against the air conditioning compressor components
  • BS3218E - EQUIPMENT:APPLIANCE:AIR CONDITIONER: The engine air intake hose could rub against the air conditioning compressor components
  • Bs3240e - ENGINE AND ENGINE COOLING:COOLING SYSTEM:RADIATOR ASSEMBLY: Coolant filling of the radiator surge tank might be erratic and create air pockets
  • BS3210ER1 - EQUIPMENT:ELECTRICAL: New auxiliary heater pump piping configuration
  • LI1953E - SEATS: Moisture may accumulate in the space under the driver's seat and cause corrosion of the power steering hydraulic fittings and piping.
  • BS3372E - EQUIPMENT ADAPTIVE/MOBILITY: Front defroster unit hose clamp too large for proper installation
  • APS3146E - ELECTRICAL SYSTEM: A new power switch relay design is now available
  • LI3402E - ENGINE AND ENGINE COOLING: Low coolant level sensor warning
  • BS3310ER1 - ENGINE (PWS): Cummins code 1242 for accelerator interlock circuit
  • BS3359ER1 - ELECTRICAL SYSTEM:SOFTWARE: Cummins isl10 engine does not have the configuration to support fault code 2448
  • BS3148ER1 - ENGINE AND ENGINE COOLING: Ventilate the engine compartment
  • bs3735er1 - ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:MANIFOLD/HEADER/MUFFLER/TAIL PIPE: Flexible bellows n79197 and n79198 may have an exhaust leak near the rigid exhaust pipe.
  • BS3447E - FUEL SYSTEM, OTHER:STORAGE:TANK ASSEMBLY: Hydraulic tank bushing failure after campaign.
  • LI3446ER2 - EQUIPMENT: Introducing new hardware and installation procedure for pitman arm. (r2 revision is for: road number and vin has been updated for l860 ttc)
  • li3788er1 - EQUIPMENT ADAPTIVE/MOBILITY: Introduction of nord-lock washers to front engine mount bolts with new torque specification for improved clamping. (r1 rephrased the document justification)
  • li3478er1 - ELECTRICAL SYSTEM:SOFTWARE: Incompatibility of actia gauge programs a fault may appear on the actia gauge if an incorrect program version is used (r1 modifications: speedo sw 109633v08_00 changed to 109633v08_02 for atuq. For ttc speedo sw 116724v04_35 changed to 11
  • li3446er5 - STEERING:GEAR BOX:SHAFT PITMAN: Introducing new hardware and installation procedure for pitman arm. (r5 updated the torque value in procedure line 1.9)
  • LI3478E - ELECTRICAL SYSTEM:SOFTWARE: This communication is a letter of information concerning a fault that may appear on the actia gauge if an incorrect program version is used.
  • BS3667E - STRUCTURE: This communication is a service bulletin concerning the vertical beam that might crack above front door second post capping.
  • BS3735ER1 - ENGINE AND ENGINE COOLING:EXHAUST SYSTEM: Flexible bellows n79197 and n79198 may have an exhaust leak near the rigid exhaust pipe.
  • LI3714 - EQUIPMENT: This letter is to inform that cr3670e replaces cr3492er3 for l573, l640, l671, l727, l787 and l902.
  • LI3713 - EQUIPMENT: This letter is to inform that for l559, cr3669e replaces cr3492er3
  • LI3788ER1 - EQUIPMENT: "introduction of nord-lock washers to front engine mount bolts with new torque specification for improved clamping. (r1 rephrased the document justification)"
  • LI3478ER1 - ELECTRICAL SYSTEM: "incompatibility of actia gauge programs a fault may appear on the actia gauge if an incorrect program version is used (r1 modifications: speedo sw 109633v08_00 changed to 109633v08_02 for atuq. For ttc speedo sw 116724v04_35 changed to 1
  • LI3446ER5 - SUSPENSION: Introducing new hardware and installation procedure for pitman arm. (r5 updated the torque value in procedure line 1.9)
  • BS3497ER1 - ENGINE AND ENGINE COOLING: Manufacturing tolerances do not always allow optimal starter engagement. Starter shim removal is required.
  • BS3457E - ENGINE AND ENGINE COOLING: Coolant supply to mk2 radiator might be erratic and create air pocket in radiator
  • BS3447ER1 - EQUIPMENT: Hydraulic tank bushing failure after campaign
  • BS2030E - ENGINE AND ENGINE COOLING: Rubber support breaks on the horizontal cac pipe.
  • APS3429ER1 - ELECTRICAL SYSTEM: Terminal lugs of the battery cables may crack due to stress.
  • BS3310ER2 - VEHICLE SPEED CONTROL: Cummins code 1242 for accelerator interlock circuit
  • BS3270E - ELECTRICAL SYSTEM:ALTERNATOR/GENERATOR/REGULATOR: Unable to perform stationary regeneration.
  • LI3446ER4 - STEERING: Introducing new hardware and installation procedure for pitman arm.
  • LI3446ER3 - STEERING: Introducing new hardware and installation procedure for pitman arm.
  • LI3788E - ENGINE (PWS): Introduction of nord-lock washers to front engine mount bolts with new torque specification for improvised clamping.
  • LI3770E - ENGINE (PWS): No access to suspend #6 lifter. Cut hole for access to #6 cylinder exhaust lifter.
  • LI3732E - ENGINE (PWS): Procedure to follow when replacing a plastic motorize valve by a metal motorize valve. For the driver's compartment defroster valve.

© dot.report 2024

Use of this information constitutes acceptance for use in an AS IS condition. There are NO warranties, implied or otherwise, with regard to this information or its use. Any use of this information is at the user's risk. It is the responsibility of user to evaluate the accuracy, completeness or usefulness of any information, opinion, advice or other content. EACH USER WILL BE SOLELY RESPONSIBLE FOR ANY consequences of his or her direct or indirect use of this web site. ALL WARRANTIES OF ANY KIND ARE EXPRESSLY DISCLAIMED. This site will NOT BE LIABLE FOR ANY DIRECT, INDIRECT or any other kind of loss.