Peterbilt 320 2011

• Recall 150752 [USA]: Rear turn signals that illuminate at the same time as the brake lights may create confusion and impair the effectiveness of the brake lights, increasing the risk of a crash.
  Paccar incorporated (paccar) is recalling certain 1990-2020 peterbilt 320 and 520 vehicles built with specific amber rear turn signals. The turn signals may also light up with the stop/tail lights when the brakes are applied. As such, these vehicles fail to comply with the requirements of federal motor vehicle safety standard (fmvss) number 108, "lamps, reflective devices, and associated equipment."
  paccar will notify owners, and for trucks with rear amber lights, dealers will add a jumper harness between the chassis electrical harness and amber tail lights, free of charge. The recall began august 1, 2019. Owners may contact paccar customer service at 1-940-591-4220. Paccar's number for this recall is 19pbc.
  owners may also contact the national highway traffic safety administration vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to www.Safercar.Gov.

  Show Content

• Recall 111047 [USA]: If engine oil comes into contact with a hot surface, there is an increased risk of a fire.
  Paccar incorporated (paccar) is recalling certain model year 2010-2016 kenworth t440, t800, and w900 trucks manufactured august 31, 2009, to april 20, 2015, and 2008-2015 peterbilt 320, 337, 348, 365, 382, and 384 trucks manufactured july 27, 2007, to april 28, 2015, and equipped with certain cummins westport isl g engines. Excessive engine crankcase pressures may cause the 90-degree elbow of the vent tube assembly to detach from the crankcase ventilation breather, possibly allowing engine oil to come into contact with hot surfaces.
  cummins will notify owners on behalf of paccar, and cummins service centers will administer the repairs which include securing the ends of the 90-degree elbow and reprogramming the electronic control module (ecm) with software that can adjust the engine output under misfire conditions to limit crankcase pressures. These repairs will be performed free of charge. The recall began on june 12, 2015. Owners may contact kenworth customer service at 1-425-828-5000, peterbilt customer service at 1-940-591-4000 or cummins inc. At 1-800-343-7357. Paccar's number for this recall is 15kwh and 515-g.
  owners may also contact the national highway traffic safety administration vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to www.Safercar.Gov.

  Show Content

• Recall 109480 [USA]: Undertorqued tie rod end clamp bolts are susceptible to corrosion, which may cause loose bolts to separate resulting in a loss of vehicle control and an increased risk of a crash.
  Paccar incorporated (paccar) is recalling certain model year 2009-2015 peterbilt 320, 365, 367, 388, and 389 trucks manufactured july 21, 2008, to february 28, 2014. The front axle tie rod end clamp bolts may be improperly torqued.
  paccar will notify owners, and dealers will replace the front axle tie rod assembly on any vehicle where the factory installed assembly has not been previously replaced, free of charge. Owners were mailed interim notices on may 11, 2015. The recall began on april 4, 2016. Owners may contact peterbilt customer service at 1-940-591-4220. Paccar's number for this recall is 215-c.
  owners may also contact the national highway traffic safety administration vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to www.Safercar.Gov.

  Show Content

• Recall 2015211 [Canada]: Engine
  On certain vehicles equipped with cummins westport isl-g engines, excessive engine crankcase pressure could cause the vent tube assembly elbow to detach from the breather. This could allow engine oil to come in contact with hot surfaces, increasing the risk of fire resulting in injury and/or damage to property. Correction: dealers will install clamps at both ends of the elbow of the breather tube assembly and reprogram the electronic control module (ecm) to improve diagnostic capabilities.

  Show Content

• Recall 2015078 [Canada]: Steering
  On certain vehicles, the tie rod end clamp bolts may not have been tightened to the correct specification. As a result, the tie rod ends could loosen, corrode, and eventually separate from the tie rod, resulting in a loss of steering control, increasing the risk of a crash causing injury and/or damage to property. Correction: dealers will replace tie rod assembly where the factory installed assembly has not been replaced.

  Show Content

To ensure accuracy and for your safety, it is recommended to do a free VIN recall check here or here [USA] - UK - Canada.

Bulletins are notices put out by manufacturers in conjunction with the NHTSA to notify the public of manufacturing issues or changes.