Polaris Slingshot 2015

• Recall 146111 [USA]: Damaged terminals may result in the loss of forward and rear lighting, instrument cluster gauges, or power steering assist. any of these scenarios increase the risk of a crash.
  Polaris inc. (polaris) is recalling certain 2015-2019 slingshot motorcycles. Excessive electrical current may damage the battery fuse holder terminals.
  polaris will notify owners, and dealers will inspect the battery fuse block terminals and relocate the 50 amp chassis fuse, free of charge. The recall began october 24, 2019. Owners may contact polaris customer service at 1-855-863-2284. Polaris's number for this recall is t-19-01.
  owners may also contact the national highway traffic safety administration vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to www.Safercar.Gov.

• Recall 130023 [USA]: The melted voltage regulator can increase the risk of a fire. the loss of a tail light can increase the risk of a crash.
  Polaris industries (polaris) is recalling certain 2015-2016 polaris slingshot, slingshot sl and slingshot sl le motorcycles equipped with a backup camera. The back-up camera may fail internally, possibly melting the voltage regulator and blowing the fuse for that circuit, thereby preventing the taillight from functioning properly. As such, these vehicles fail to comply with the requirements of federal motor vehicle safety standard (fmvss) number 108, lamps, reflective devices, and associated equipment.
  polaris will notify owners, and dealers will inspect and replace the back-up camera, as necessary, free of charge. The recall began january 2, 2019. Owners may contact polaris at 1-855-863-2284. Polaris' number for this recall is t-18-04.
  owners may also contact the national highway traffic safety administration vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to www.Safercar.Gov.

• Recall 134411 [USA]: If the seat belt buckle or seat back detach from the seat base, there would be an increased risk of injury in the event of a crash. if the driver's seat unexpectedly moves, it can cause the driver to lose control of the motorcycle, increasing the risk of a crash.
  Polaris industries, inc. (polaris) is recalling all 2015-2018 polaris slingshot motorcycles. The driver-seat and passenger-seat seat belt and seat back anchoring bracket may have been improperly welded. Additionally, differences in the seat assembly may prevent proper latching of the seat slider, allowing the driver's seat to move unexpectedly.
  polaris will notify owners, and dealers will inspect the seat belt bracket and seat back welds, and the seat slider latching function. If the weld is missing or incomplete, or if the slider doesn't latch properly, the seat bases will be replaced, free of charge. The recall began on april 16, 2018. Owners may contact polaris customer service at 1-855-863-2284. Polaris' number for this recall is t-18-01.
  owners may also contact the national highway traffic safety administration vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to www.Safercar.Gov.

• Recall 120921 [USA]: Contamination of the rear speed sensor will disable the abs and traction/stability control, increasing the risk of a crash.
  Polaris industries, inc. (polaris) is recalling certain 2015-2017 slingshot vehicles. The affected vehicles previously had their rear swingarms replaced during the remedy of nhtsa recall number 16v-255. The replacement swingarms may have been installed without the sealing grommets installed, potentially resulting in road debris contaminating the rear wheel speed sensor.
  polaris will notify owners, and dealers will inspect the swingarms for missing grommets, installing them as necessary, free of charge. The recall began june 13, 2017. Owners may contact polaris customer service at 1-888-704-5290. Polaris' number for this recall is t-17-04.
  owners may also contact the national highway traffic safety administration vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to www.Safercar.Gov.

• Recall 125607 [USA]: Due to the insufficient swing arm strength, the swing arm may fracture resulting in a loss of momentum or vehicle control, increasing the risk of a crash.
  Polaris industries, inc. (polaris) is recalling certain model year 2015-2017 slingshot motorcycles manufactured march 4, 2014, to september 7, 2016. The affected vehicles may have been manufactured with a swing arm that has insufficient strength.
  polaris will notify owners, and dealers will inspect, and repair or replace the swing arm, as necessary, free of charge. The recall began december 2016. Owners may contact polaris customer service at 1-855-863-2284. Polaris' number for this recall is t-16-06.
  owners may also contact the national highway traffic safety administration vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to www.Safercar.Gov.

• Recall 109425 [USA]: The insufficient clearance may allow the fuel line to rub against the hood until it leaks fuel. a fuel leak in the presence of an ignition source can increase the risk of a fire.
  Polaris idustries, inc. (polaris) is recalling certain model year 2015-2017 slingshot motorcycles manufactured march 4, 2014, to october 7, 2016. The affected vehicles may have insufficient clearance between the fuel line and the hood structure.
  polaris will notify owners, and dealers will replace the replace the engine fuel line, and inspect the retention clips to reduce the risk of interference, free of charge. The recall began december 2016. Owners may contact polaris customer service at 1-855-863-2284. Polaris' number for this recall is t-16-03.
  owners may also contact the national highway traffic safety administration vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to www.Safercar.Gov.

• Recall 110742 [USA]: A loss of headlights can reduce driver visibility, increasing the risk of a crash.
  Polaris industries, inc. (polaris) is recalling certain model year 2015-2016 slingshot motorcycles manufactured april 21, 2014, to october 22, 2015, slingshot sl motorcycles manufactured april 28, 2015 to october 23, 2015, and slingshot sl se motorcycles manufactured december 15, 2014, to october 22, 2015. In the affected motorcycles, the headlight relay may fail and result in a loss of headlights.
  polaris will notify owners, and dealers will replace the single headlight relay with a circuit that uses two headlight relays, free of charge. The recall began on december 3, 2015. Owners may contact slingshot customer service at 1-855-863-2284. Polaris' number for this recall is sli-15-05.
  owners may also contact the national highway traffic safety administration vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to www.Safercar.Gov.

• Recall 110012 [USA]: If the steering pinion gear disengages from the steering rack, a loss of steering control could result, increasing the risk of a crash.
  Polaris industries, inc. (polaris) is recalling certain model year 2015 slingshot motorcycles manufactured august 26, 2014, to january 9, 2015, and 2015 slingshot sl motorcycles manufactured august 18, 2014, to january 10, 2015. In the affected motorcycles, the upper pinion bearing may fail on the steering rack assembly, resulting in the pinion gear disengaging from the steering rack.
  polaris will notify owners, and dealers will replace the steering rack assembly, free of charge. The recall began on january 30, 2015. Owners may contact polaris customer service at 1-855-863-2284. Polaris' number for this recall is sli-15-02.
  owners may also contact the national highway traffic safety administration vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to www.Safercar.Gov.

• Recall 106093 [USA]: If the roll hoops do not meet strength specifications, in the event of a rollover crash they may not provide proper protection, increasing the risk of a personal injury.
  Polaris industries, inc. (polaris) is recalling certain model year 2015 slingshot motorcycles manufactured august 26, 2014, to december 16, 2014, and 2015 slingshot sl motorcycles manufactured august 18, 2014, to december 15, 2014. The affected motorcycles may be equipped with roll hoops that do not meet hardness specifications.
  polaris will notify owners, and dealers will replace the roll hoops, free of charge. The recall began on january 30, 2015. Owners may contact polaris customer service at 1-651-408-7579. Polaris' number for this recall is sli-15-01.
  owners may also contact the national highway traffic safety administration vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to www.Safercar.Gov.

• Recall RM/2018/045 [UK]: The backup camera could fail internally and melt the voltage regulator over-mold
  The backup camera could fail internally and cause the fuse for the rear lights to blow.
  inspect the camera version and replace if necessary.

• Recall RM/2016/044 [UK]: 1. brakes may fail. 2. risk of fire. 3. loss of control
  1. It is possible during production the brake pressure switch (brake light switch) may have been over torqued. This could result in a loss of brake fluid and subsequent reduction in braking performance which could cause a collision. 2. It is possible during production the fuel pipe may have been placed to close too the hood which resulted in insufficient clearance between the two. This could result in the abrasion of the fuel pipe which could leak. If this happens in the presence of an ignition source there will be a risk of fire. 3. It has been identified that the suspension swinging arm may not have been manufactured to the correct specification which affects its strength and could cause it to fail. If this occurs the directional control of the machine could be affected.
  recall all the affected machines to inspect check and if required replace the defective components.

• Recall RM/2019/028 [UK]: The vehicle's electrical current requirements may exceed the capability of the battery fuse box terminals
  Excess current may lead to terminal damage
  reposition the main chassis fuse

• Recall RM/2018/012 [UK]: Seat base frame may be defective
  Driver-side and passenger-side seatbase frames may have been improperly manufactured driver-side seatbase frames may also contain a seat slider defect.
  frames on affected vehicles will be checked and if necessary replaced.

• Recall 2019545 [Canada]: Electrical
  Issue: on certain vehicles, the terminals of the battery fuse block could be damaged during normal driving. This can result in a loss of forward and rear lighting, a loss of gauges, and a loss of power steering assist. Safety risk: a loss of forward lighting would reduce visibility. A loss of rear lighting could make the vehicle less visible and cause a following driver to not recognize that a vehicle ahead is braking. A loss of power steering assist could make the vehicle difficult to steer. These failures could increase the risk of a crash. Corrective actions: polaris will notify owners by mail and instruct them to take their vehicle to a dealer to inspect the battery fuse block terminals and relocate the 50-a chassis fuse.

• Recall 2019136 [Canada]: Seats and restraints
  Issue: on certain vehicles, the seat base may have been assembled improperly. This could cause the seat belt buckle to detach or cause the seat slider not to latch properly. This could result in unexpected movement of the seat or seat back. Safety risk: if the seat moves while driving, vehicle control could be affected. In a crash, a seat that moves or a seat belt that separates could increase the risk of injury. Corrective actions: the company will notify owners by mail. Owners will be instructed to take their vehicle to a dealer to have the seat belt bracket and the seat slider latch inspected. If an incomplete or missing weld is found, or if a slider does not latch properly, the seat base will be replaced. Note: this supersedes recall 2018-144. Vehicles repaired under the previous recall do not require repair under this recall.

• Recall 2018633 [Canada]: Electrical
  On certain vehicles, the rearview camera could fail internally and overheat, creating a fire risk. This could also result in loss of tail light function. Both of these conditions could increase the risk of a crash causing injury and/or damage to property. Correction: dealers will inspect and replace the camera as necessary.

• Recall 2018144 [Canada]: Seats and restraints
  On certain vehicles, the seat belt buckle and seat back may dislodge from seat base and/or the seat sliders may not latch properly. If the seat were to slide unexpectedly, vehicle control could be affected, and/or in the event of a crash, if the seat belt buckle and seat back were to dislodge from the seat base, an occupant may not be properly restrained, which would increase the risk of injury and/or damage to property. Correction: dealers will inspect the weld of the seat belt bracket and inspect the seat slider latching function. If a weld is found incomplete or missing, or if a slider does not latch properly, the seat base will be replaced. Note: this recall is superseded by recall 2019136. Please see recall 2019136 for more information.

• Recall 2017294 [Canada]: Suspension
  On certain vehicles which had a rear swing arm previously replaced under recall t-16-06 (transport canada no. 2016-520), the swing arm may have been installed without two dust plug grommets. Without dust plug grommets, debris could contaminate the rear wheel speed sensor, which could affect abs and traction/stability control functions, increasing the risk of a crash causing injury and/or property damage. Correction: dealers will inspect for the presence of the grommets, and install if found missing. Note: if the speed sensor were to become inoperative, abs and traction/stability control dash lights would illuminate.

• Recall 2017155 [Canada]: Seats and restraints
  Certain vehicles may not comply with canada motor vehicle safety standard (cmvss) 208 - occupant protection in frontal impacts. The vehicle fails to provide an audible warning if the driver's seatbelt is not buckled, contrary to the requirements of the standard. This could increase the risk that the driver remain unbelted, increasing the risk of injury in a crash. Correction: dealers will install a newly designed jumper harness which included the required seatbelt chime.

• Recall 2016521 [Canada]: Fuel supply
  On certain vehicles, there may be insufficient clearance between the fuel line and hood structure. This can result in abrasion of the fuel line, which could result in a potential fuel leak. A fuel leak in the presence of an ignition source could result in a fire causing injury and/or property damage. Correction: dealers will replace and re-route the fuel line.

• Recall 2016520 [Canada]: Suspension
  On certain vehicles, due to a defect in manufacturing, the rear swing arm may not meet strength specifications. This could result in the potential for the swing arm to fracture if the vehicle were to strike a pothole, or be subjected to a severe event, which could result in a a loss of control and a loss of propulsion which, in conjunction with traffic and road conditions, and the driver's reactions, could increase the risk of a crash causing injury and/or property damage. Correction: dealers will replace the rear swing arm with a swing arm with a stronger geometry.

• Recall 2015558 [Canada]: Lights and instruments
  On certain vehicles, the electrical relay used for the headlight circuit could cause the headlights to operate intermittently or turn off while the vehicle is in operation. This could compromise the driver's visibility, which could result in a crash causing injury and/or property damage. Correction: dealers will replace the single headlight relay with a circuit that uses two relays.

• Recall 2015020 [Canada]: Steering
  On certain vehicles, the steering rack may have been manufactured with a defective bearing. This could affect steering system function, or result in a loss of steering control, which could increase the risk of a crash causing injury and/or damage to property. Correction: dealers will replace the steering rack assembly.

• Recall 2015019 [Canada]: Structure
  On certain vehicles, some roll hoops do not meet the manufacturer's hardness specifications and may not provide the level of protection that was originally intended. In the event of a rollover, this could increase the risk of injury and/or damage to property. Correction: dealers will inspect, and if necessary, replace the roll hoops.

To ensure accuracy and for your safety, it is recommended to do a free VIN recall check here or here [USA] - UK - Canada.

Bulletins are notices put out by manufacturers in conjunction with the NHTSA to notify the public of manufacturing issues or changes.

• Seatbelt retractor failure investigation as of 20170918

  There is no summary currently available
  

  Show Content

• Front wheel failure investigation as of 20150420

  There is no summary currently available
  

  Show Content

While i was shifting, when i depressed the clutch, the engine fully revved. During this instance, i tapped the gas pedal to see if it was sticking. It was not sticking and was fully out. This happened so fast as i was driving on hills in the mountains and had to turn the key off, which was the only was to stop the revving. By the time all this had happened though, the tach went to 7,000 rpm. The motor redlines at about 6400, just fyi. This never happened before and a serious outcome could have developed, and would have definitely developed if my wife had been driving the bike. Thinking back, i was probably doing 40-50 mph. Sunny, about 90 degrees f. In the mountains with a lot of hills and turns. Now, returning home it "sort of" happened again. The engine revved to about 3500 rpm this time while depressing the clutch to shift. However, now being alert to the issue, i put it back in gear. Then put it in and out of gear to see if the revving stopped. Just fyi, yes the bike is a 2015. However, the bike only has 7,600 miles. When i arrived home, i had my wife depress the gas pedal several times to see if i noticed anything. First glance, without really investigating, i could see no linkage in the engine bay. This is a very dangerous situation as this just happened today. My wife will not be driving this bike now for reasons stated above.

While i was shifting, when i depressed the clutch, the engine fully revved. During this instance, i tapped the gas pedal to see if it was sticking. It was not sticking and was fully out. This happened so fast as i was driving on hills in the mountains and had to turn the key off, which was the only was to stop the revving. By the time all this had happened though, the tach went to 7,000 rpm. The motor redlines at about 6400, just fyi. This never happened before and a serious outcome could have developed, and would have definitely developed if my wife had been driving the bike. Thinking back, i was probably doing 40-50 mph. Sunny, about 90 degrees f. In the mountains with a lot of hills and turns. Now, returning home it "sort of" happened again. The engine revved to about 3500 rpm this time while depressing the clutch to shift. However, now being alert to the issue, i put it back in gear. Then put it in and out of gear to see if the revving stopped. Just fyi, yes the bike is a 2015. However, the bike only has 7,600 miles. When i arrived home, i had my wife depress the gas pedal several times to see if i noticed anything. First glance, without really investigating, i could see no linkage in the engine bay. This is a very dangerous situation as this just happened today. My wife will not be driving this bike now for reasons stated above.

Tl* the contact owns a 2015 polaris slingshot. The contact stated that he checked the tire pressure and removed the front passenger side tire. Afterwards, grease came out of the cracked seal and the wheel bearing looked worn and loose. The vehicle was not diagnosed or repaired. The dealer and manufacturer were not made aware of the failure. The failure mileage was 2,050.

Steering racket pinion broke fell apart bearing fell out

Tl* the contact owns a 2015 polaris slingshot. While driving, the cruise control failed to operate. The vehicle was taken to tousley motorsports (located at 1400 co rd e east, st paul, mn 55110, (651) 483-8296) where it was diagnosed that the rear wheel bearing and sensor were fractured. The vehicle was not repaired. The manufacturer was not notified of the failure. The approximate failure mileage was 37,000. The vin was not available.

Electrical short/fire in backup camera causing failure in break lights, tail lights, abs, cruise control, radio, blinkers, horn. Vehicle was being operated at approximately 60 mph when incident occurred.

After less than a year of operation, the brake failure light began turning on. I took the vehicle to auburn powersports at least 8-9 times to fix the problem and every time the problem was not fixed. All recalls are complete. The light comes on every time i ride the vehicle. It comes on when the vehicle is in motion on any highway. This has been going on for two years.

The brake pressure sensors fail. Randomly or when brakes are touched this causes the cruise control to suddenly disengage and a warning light in the instrument panel indicates brake failure. Polaris recommends "do not operate vehicle". Leaving driver and passenger stranded. When the brake failure light is reset the cycle repeats.

Wish i get my money back i hate the bike the heat that come inside be burning my feet it to hot inside to ride they did a arm change for the recall wheel are not even straight steering wheel be getting hard bike suck wish i had my money back08

Tl* the contact owns a 2015 polaris slingshot. The contact received nhtsa campaign numbers: 16v754000 (fuel system, gasoline) and 16v755000 (suspension) however, the parts to do the repairs were unavailable. The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repair. The manufacturer was notified of the issue but no further information was provided. The contact stated that he asked to speak to a manager and was placed on an extended hold when he disconnect. The contact had not experienced a failure. Parts distribution disconnect.

Tl* the contact owns a 2015 polaris slingshot. The contact received a recall notification of nhtsa campaign numbers: 16v755000 (power train) and 16v754000 (fuel system, gasoline). The part to do the repair was unavailable. The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue. The vin was unknown. The contact had not experienced a failure. Updated 02/07/2017*ct

Tl* the contact owns a 2015 polaris slingshot. The contact received notification of nhtsa campaign numbers: 16v754000 (fuel system, gasoline) and 16v755000 (power train); however, the parts to do the repairs were unavailable. The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repairs. The contact stated that the brake warning indicator remained illuminated and the passenger side seat belt did not pull out. The failure mileage was unknown. Parts distribution disconnect.

Polaris has issued a stop sale on slingshots due to safety defects but not a stop drive for us who have a slingshots with the same safety defects. Why???

Tl* the contact owns a 2015 polaris slingshot. The contact received notification of nhtsa campaign numbers: 16v754000 (fuel system, gasoline) and 16v755000 (power train); however, the parts to do the repairs were unavailable. The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repairs. The contact stated that the brake warning indicator remained illuminated and the passenger side seat belt did not pull out. The failure mileage was unknown. Parts distribution disconnect.

Tl* the contact owns a 2015 polaris slingshot. The contact received notification of nhtsa campaign number: 16v755000 (power train). The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue. The contact had not experienced a failure.

Tl* the contact owns a 2015 polaris slg slingshot. The contact received notification of nhtsa campaign numbers: 16v754000 (fuel system, gasoline) and 16v755000 (power train). The parts to do the repairs were unavailable. The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repairs. The contact spoke to pocono motorsports (938 pa-940, pocono lake, pa 18347) who stated that they were waiting for the manufacturer to send the repair parts. The manufacturer was made aware of the issue and stated that they were manufacturing the parts and did not have a time frame for when they would become available. The contact had not experienced a failure. Parts distribution disconnect.

Tl* the contact owns a 2015 polaris slingshot. The contact received notification of nhtsa campaign number: 16v755000 (suspension); however, the part to do the repair was unavailable. The contact stated that the manufacter exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue. The contact had not experienced a failure.

Consumer stated driving on hwy 80 when the car starts running weird, i slow down and pull to the slow lane. Then vehicle note smoke and flames coming into the area where my feet are. Got out and car burned to the ground..Bf

On august 13, 2016 my brother was driving his 2015 polaris slingshot (model # t15aapfaab) when the vehicle suddenly veered into on coming traffic. His vehicle then collided with a car being driven in the opposite direction, my brother did not survive. Soon after, it was discovered that his vehicle may be included it the nhtsa safety recall 15v-022 for loss of steering (polaris recall sli-15-02). I conveyed this information to the livonia, michigan police officer who was investigating the collision. Officer hayne, of the livonia pd then contacted the polaris dealer, monroe motorsports, in monroe, michigan where the vehicle was purchased to investigate. Monroe motorsports informed her that the only recall on the vehicle was sli-15-05, headlights which was completed the day of the collision. Hearing this, i explained to officer hayne that the information on the nhtsa recall contradicted these findings. I further explained to officer hayne that the vehicle owned and operated by my brother on the day of the collision clearly fit all of the nhtsa requirements. Model t15aapfaab production date 12/06/2014 vin 57xaapfa0f510xxxx officer hayne then contacted polaris and received a reply further indicating that nhtsa recall 15v-022 did not include this vehicle. How can a vehicle with the exact model number, and a production date and vin number that obviously fall within the recalled vehicles, not be recalled? Additionally, i noticed that the number of recalled vehicles may be incorrect. If you subtract the starting recalled vin [xxx] from the ending recalled vin [xxx], the total amount of recalled vehicles should be 2,344 and not the 1,896 stated in the nhtsa recall. I fear that my brother's vehicle may be one of the 448 overlooked defective vehicles. I await your reply in this serious matter. Information redacted pursuant to the freedom of information act (foia), 5 u.S.C. 552(b)(6). *tr

Tl* the contact owns a 2015 polaris slingshot. While driving at any speed, heat emitted from the radiator. While exiting the motorcycle, the contact feet was burned due to the extreme heat all the time. Medical attention was not required. The motorcycle was taken to the dealer where it was diagnosed that an air flow kit needed to be installed. The vehicle was repaired. The manufacturer was notified of the failure and stated that they were unaware. The failure mileage was approximately 5,000. Updated 09/28/16*lj *tr

After just less than 3,500 miles, the master brake failure light came on during a normal drive. Quickly brought the vehicle back to garage. Followed owner's manual guidelines, checked brake fluid level and contacted the dealer. Dealer indicated that this is a very common problem, no need to bring in for inspection if there is still braking. I expressed my concern with the brake failure light, and if the brakes do fail, this would result in a catastrophic accident. Over the phone they indicated that this is a very common issue; if so then polaris should fixed it quickly, as to the severity if the brakes do fail.

Brake failure light on dash. Abs and cruise control is disabled. This vehicle is 2 years old with less than 2,500 miles on it. This problem has plague most owners of the slingshot with the slingshot forums working to try to solve problem. This is a serious problem along with the spongy (air in brake lines) which has not be adequately addressed by polaris. This brake failure light is on all the time and of course is of concern only when the vehicle is moving. *tr

I was driving my slingshot down the road . The road is a sweeping curve around a pond . The cruise control turned on .The vehicle accelerated extremely fast forcing me off the road . I then stuck a tree . Resulting in two fractured ribs and a fractured spine .

Throttle sticks when shifting gears--and sometimes the engine will rev real high with foot off gas. Going into turns on blue ridge parkway-i take foot off gas and it keeps going as if i hadn't--scary!!

Cpsc:x15a0005a. 2015 polaris slingshot. Consumer stated problems with the high revolutions when he is shifting the transmission while driving. *ln

The wheel bearings failed at 1500 miles... Updated 12/08/2017*cn

In regards to an intermittent problem i am experiencing with my polaris slingshot purchased on june 6, 2015. Shortly after purchase i began experiencing extremely high engine evolutions during the process of shifting gears. I took my vehicle on 06/162015 closest polaris dealership xtreme machines located 700 state hwy 33 west, millstone township, nj 732-786-9696. The mechanic performed the road test but was not able to identify the problem. I then returned to the dealer as the problem was becoming more frequent. The dealer informed me a ecu was updated and should fix the problem but to no avail. *js

Tl* the contact owns a 2015 polaris slingshot. The contact stated that the motorcycle accelerated suddenly without warning. The contact was able to stop the motorcycle by shifting down the clutch and turning the key. The vehicle was taken to the dealer, but the technician was unable to duplicate the failure. When the contact picked up the vehicle, the traction control light illuminated and the cruise control stopped working. The vehicle was not repaired. The failure mileage was 5,000.

We took our slingshot sl back to our dealer to have them remove and check front wheel rims for crackles due to recent reports of over 10 other slingshot owners having their wheels rims failure due to cracks while driving. The dealer would multiple casting imperfections and one large crack approx 1 inch in length and 0.1 ml in width (wide enough to put a fingernail). Polaris was contacted by the dealer and by us - at this time polaris is refusing to allow dealers to replace these defective cracked wheel rims. The second safety issue this motorcycle has is the rpms increase when you take your foot off the gas pedal and hold in the clutch to shift gears causing the motorcycle to rev up. We have been told the wheel rims are cast aluminum from china and are concerned about our safety when driving with this vehicle. At this time we have parked our new 2015 slingshot until these safety issues can be addressed by polaris. *tr

From day one ive experienced occasional to frequent engine flares, which is, when i press the clutch all the in while taking my foot off of the throttle, the engine rpm will hang at it's current value and will sometimes increase 500-1000 rpms and remain there for several seconds before reducing on it's own. At times i can go through several shifting events to hours of normal operation without problems but, the flaring has always happened on every ride ive been on. About three weeks ago he re-flashed the ecu which made the engine run smoother but did not fix the flaring issue. My dealer tells me that polaris tells him, that engine flaring during shifting is normal and shouldnt be worried about. If i'm driving it incorrectly or "something is interfering by holding the throttle, it would happen every time i shifted however, after today i need action. I was in my garage starting my 2/15 built ss sl with 3500 miles. As i have from day one, i allowed the ecu to complete the booting cycle and allowed the fuel pump to stop before i pressed the dashboard start button. The engine start cycle started with a slightly different sound, almost as if the engine backfired slightly but not an actual backfire. As the engine came to life the rpm instantly went to the rev limiter and held there for 1.5 to 2.0 seconds then started down in a few decelerating stages to idle before i had my wits to turn off the key. I was stunned and my wife, who was standing in front of it, just about dislocated a hip getting out of the way. The fact that you must press the clutch in in order for the start cycle to commence and the fact that i always start in neutral, averted catastrophe. All owners and polaris should be on alert and are hereby notified my dealer has offered to come and pick it up. Polaris is not being responsive at all on this issue.

Tl* the contact owns a 2015 polaris slingshot. The contact received notification of nhtsa campaign numbers:15v022000 (steering) and 15v020000 (structure); however, the parts to do the repairs were unavailable. The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repair. The manufacturer was notified of the issue. The contact had not experienced a failure. Updated 5/18/15*cn the consumer stated the motorcycle was repaired. Updated 06/02/15*jb

Gas pedal revving by itself between 1-2-3-4 gears when taking foot off the pedal i reported the problem to dealer and they had no recall form polaris. I called the company and dealer 3-4 times and they had no answer for me. The gas pedal vevvs 500 to 3000rpm when i release the throttle gas pedal .I just went to the dealer for a change of micro clutch switch with no success on may19-2015. Your immediate attention would be appreciated. The slingshot forum for owners have had many many complaints with no results. [xxx] [xxx] there is a slingshot rally in maggie valley nc.On june 09-2015 with around 100 owners going to dragon tail ride with 318 curves in 11miles. I am concern. Reply asap information redacted pursuant to the freedom of information act (foia), 5 u.S.C. 552(b)(6).? *jb

Tl*the contact owns a 2015 polaris sling shot (n/a). The contact stated that while driving 10 mph, the traction control warning light illuminated. The failure recurred multiple times. The vehicle was taken to the dealer, where it was not diagnosed or repaired. The manufacturer was made aware of the failure. The failure mileage was 25.