NTB12-043

SB-10044039-4198
Classificatio n:
Reference:
EL12-034
Date:
NTB12-043
May 4, 2012
2008 – 2012 ROGUE ENGINE HARNESS REPLACEMENT
APPLIED VEHICLES:
2008 – 2012 Rogue (S35)
SERVICE INFORMATION
Front
If for any reason the engine harness is replaced, during the replacement of the harness,
install a rubber protective pad on the battery tray support bracket at the location shown in
Figure 1 below. Refer to the Service Procedure for installation instructions.
Install rubber
protective pad here
Battery tray
support bracket –
under battery tray
Figure 1
PARTS INFORMATION
DESCRIPTION
Rubber Protective Pad
PART #
76884-CA00A
QUANTITY
1
Nissan Bulletins are intended for use by qualified technicians, not 'do-it-yourselfers'. Qualified technicians are
properly trained individuals who have the equipment, tools, safety instruction, and know-how to do a job
properly and safely. NOTE: If you believe that a described condition may apply to a particular vehicle, DO
NOT assume that it does. See your Nissan dealer to determine if this applies to your vehicle.
1/3
SERVICE PROCEDURE
Only ½ of the
pad will be used
1. Cut the rubber protective pad in half,
length wise.
•
Only ½ (either half) of the pad will
be used.
Figure 2
Pad installed
here; clean area
2. Clean the area where the protective
pad will be installed.
•
Installation area is shown with
dashed line.
•
Clean both sides of the bracket
edge. Pad will be folded over and
attached to both sides.
Figure 2
2/3
NTB12-043
3. Attach the rubber protective pad as
shown.
4. Fold the protective pad over the
bracket edge so it covers and sticks to
both side.
Install pad
and fold over
Figure 3
NOTE: Figure 4 shows the finished installation of the protective pad on both sides of the
bracket.
Figure 4
3/3
NTB12-043

SB-10044039-8671
Classification:
Reference:
EL12-034a
Date:
NTB12-043a
May 18, 2012
2008 – 2012 ROGUE ENGINE HARNESS REPLACEMENT
This bulletin has been amended. Applied VIN and Applied Date have been added.
Please discard previous versions of this bulletin.
APPLIED VEHICLES:
APPLIED VIN:
APPLIED DATE:
2008 – 2012 Rogue (S35)
Built on or before JN8AS5M(*)(*)CW 713595
Built on or before March 28, 2012
SERVICE INFORMATION
Front
If for any reason the engine harness is replaced, during the replacement of the harness,
install a rubber protective pad on the battery tray support bracket at the location shown in
Figure 1 below. Refer to the Service Procedure for installation instructions.
Install rubber
protective pad here
Figure 1
Battery tray
support bracket –
under battery tray
PARTS INFORMATION
DESCRIPTION
Rubber Protective Pad
PART #
76884-CA00A
QUANTITY
1
Nissan Bulletins are intended for use by qualified technicians, not 'do-it-yourselfers'. Qualified technicians are
properly trained individuals who have the equipment, tools, safety instruction, and know-how to do a job
properly and safely. NOTE: If you believe that a described condition may apply to a particular vehicle, DO
NOT assume that it does. See your Nissan dealer to determine if this applies to your vehicle.
1/3
SERVICE PROCEDURE
Only ½ of the
pad will be used
1. Cut the rubber protective pad in half,
length wise.
•
Only ½ (either half) of the pad will
be used.
Figure 2
2. Clean the area where the protective
pad will be installed.
•
Installation area is shown with
dashed line.
•
Clean both sides of the bracket
edge. Pad will be folded over and
attached to both sides.
Pad installed
here; clean area
Figure 2
2/3
NTB12-043a
3. Attach the rubber protective pad as
shown.
4. Fold the protective pad over the
bracket edge so it covers and sticks to
both side.
Install pad
and fold over
Figure 3
NOTE: Figure 4 shows the finished installation of the protective pad on both sides of the
bracket.
Figure 4
3/3
NTB12-043a