14-01-007

(/B) HYUnDRI I
GROUP
nEWTHlnKlnG.
nEW POSSIBILITIES.
Technical Service Bulletin
CAMPAIGN
DATE
JANUARY 2014
NUMBER
14-01-007
MODEL
TUCSON (LM)
AUTOMATIC TRANSAXLE ECM & TCM UPDATE (SERVICE CAMPAIGN TS3)
(Si))
HYUn~RI
ECU Update
*IMPORTANT
*** Retail Vehicles Only ***
Dealers must perform this Campaign whenever an affected vehicle is in the shop for any
maintenance or repair.
When a vehicle arrives at the Service Department, access Hyundai Motor America's "Warranty
Vehicle Information" screen via WEBDCS to identify open Campaigns.
Description: This bulletin provides a procedure to update the ECM and TCM software for 2013
Tucson (LM) 2.4L vehicles to:
•
Revise the shift feeling in ECO mode
•
To
./
./
./
./
./
revise logic for the following DTCs:
P0300: Random/Multiple Cylinder Misfire Detected
P0301: Cylinder 1 - Misfire Detected
P0302: Cylinder 2 - Misfire Detected
P0303: Cylinder 3 - Misfire Detected
P0304: Cylinder 4 - Misfire Detected
Applicable Vehicles: 2013 MY Tucson (LM) 2.4L with automatic transaxles
Applicable Production Date Range: From May 24, 2012 through October 4, 2012
GDS INFORMATION:
Event #
EVENT #317
EVENT #287
Description
317 . 13MY LM 2.4 MPI P030X OTC LOGIC IMPROVEMENT
287.13MY LM 2.4 ACTIVE ECO ACCELERATION LOGIC IMPROVEMENT -TCM
WARRANTY INFORMATION:
NOTE: Submit claim on Campaign Claim Entry Screen
Circulate To: Service Manager, Warranty Manager, Service Advisors , Technicians , Fleet Repair
SUBJECT:
-·
TUCSON (LM) ECM & TCM UPDATE (SERVICE CAMPAIGN TS3)
I
-·
.. :
MODEL
ECM PART
NUMBER
EMISSION
I
' .
'
.
IGNITION
' ' •
.
IMMO
.
.
ECM ROM ID
PREVIOUS
39106-2G803
39106-2G813
39106-2G823
NO
LDC4MSOA
LDC4MTOA
LDC4MTOB
LDC4MT1B
SSB
YES
LDC4RSOA
LDC4RTOA
LDC4RTOB
LDC4RT1B
KEY
NO
LDS4MSOA
LDS4MTOA
LDS4MTOB
LDS4MT1B
SSB
YES
LDS4RSOA
LDS4RTOA
LDS4RTOB
LDS4RT1B
SU LEV
39106-2G883
NEW
KEY
ULEV
2013
TUCSON (LM)
2.4L
.
TCM ROM ID TABLE: Verify the TCM ROM ID before updating vehicle software.
MODEL
PCM (TCM) PART
NUMBER
TCM ROM ID
PREVIOUS
NEW
TLMOC24NA6
TLMOC24NA7
TLMOC24N10
39106-2G803
TUCSON (LM)
2.4L
39106-2G813
39106-2G823
39106-2G883
TSB #: 14-01-007
Page 2 of 7
TUCSON (LM) ECM & TCM UPDATE (SERVICE CAMPAIGN TS3)
GENERAL PRECAUTIONS
•
•
Connect the USB cable between the GOS and
the VCI.
Connect the 16-pin DLC connector from the VCI
into the DLC located under the driver's side
dash .
*NOTE
Make sure the battery icon at the bottom right of the GOS laptop shows at
least 50%; if not, charge the GOS or attach a battery charger.
•
Turn off all lights (Do not leave the headlight switch in auto mode) and all accessories (including
heater/air conditioner/fan , audio, heated seats, rear defroster, etc) to ensure the battery will not
be discharged during the update.
•
Perform the update with the ignition key in the ON position. (Turn the ignition key to the ON
position or press the Start-Stop Button two times without depressing the brake pedal).
•
Do not disconnect any cables connected to the vehicle or the GOS during the update .
•
Do not start the engine or turn the ignition switch OFF during the update.
*NOTE
Confirm your GOS has the most recent version. If not, connect the GOS to an
Internet port, open the GOS home page and select "Update".
If you encounter GOS related problems, call the GIT Helpline at 888-437-0308.
TSB # : 14-01-007
Page 3 of 7
SUBJECT:
TUCSON (LM) ECM & TCM UPDATE (SERVICE CAMPAIGN TS3)
GDS AUTO MODE ECM UPDATE PROCEDURE
1. From the GOS home page , select ECU Upgrade. If necessary, select the VIN.
2. Select Engine as the system and then select OK.
3. Select Auto Mode and then select Next.
4. From the System tab , select Engine and then select OK. The GDS will read the ROM ID.
Confirm the ROM is applicable as shown on Page 1, "ECM ROM ID Information ".
NOTE: Record the ROM ID in case the auto update fails and a manual update is needed .
5. Update event 317.13MY LM 2.4 MPI P030X OTC LOGIC IMPROVEMENT will display. Select
Upgrade.
• Mode
Auto Mode
>System
• Current ROM ID
jLDS4RTOA
• Latest ROM ID
jLDS4RTOB
286 13MY LM 2 4 ACTIVE ECO ACCELERATION LOGIC IMPROVEMENT-ECM
ENGINE
-~)
D Event selection
1. Review and understand relate d TSB for vehicle reprogramming.
2. Select repro gramming event f ro m Upgrade Event pull down menu above .
3. Click the Upgrade button to begin ECU upgrade.
Sample Screen
case Analysis
OTC
Current Data
Ac~':s~
6. If the screen indicates "Voltage is OK", select OK. If not, select CANCEL and charge the
vehicle battery by running the engine for 10 minutes .
7. Updating will occur until 100% is reached on the bar graph. At the prompt, turn the ignition key
OFF for 10 seconds , then turn it ON and select OK.
8. The GOS will confirm that ECM reprogramming is successfully finished. Select OK.
9. If the ECM update was not successful , go to GOS MANUAL MODE ECM UPDATE
PROCEDURE.
10. Check for Diagnostic Trouble Codes and erase any DTC .
11 . Clear the OTC in the Bluelink system according to instructions in TSB 12-BE-005-2.
12. Start the engine to confirm proper operation .
TSB #: 14-01-007
Page 4 of 7
TUCSON (LM) ECM & TCM UPDATE (SERVICE CAMPAIGN TS3)
GOS MANUAL MODE ECM UPDATE PROCEDURE
*NOTE
In the event of AUTO MODE update failure (after it initiated the progress bar):
• You must attempt MANUAL MODE. Use the ECM P/N from the vehicle's
ECM label if the correct ECM P/N is not clear from the ROM ID table.
• Replacing an ECM without carefully documenting that a MANUAL MODE
update attempt was made will result in a charge back of your claim .
1. From the GOS home page , select ECU Upgrade. If necessary, select the VIN .
2. Select Engine as the system and then select OK.
3. Select Manual Mode and then select NEXT.
4 . From the System tab , select Engine and then select NEXT.
5. Select Update event 317. Select OK.
6 . Select the correct control module part number according to ECM part number on the ECM label.
Select Upgrade .
Repair
~---1
• Current ROM ID
•Mode
• Latest ROM ID
M:inu;:i.IMode
~
ILDC4MTOB
1
11$tjH@1Hl815t•*€"•¥iilf$:1 g
• System
j
LM 2.4 IMMO : 39106/3911S.2G813
LM 24 NON IMMO · 39 10S. 2G823
ENG INE
.. ....... ........ . . ... . ,............ . . . . . ....... "
•Event Group
m. m~Y~J.ll4ACTiVE ECOAr,
D CAUTION
wmm•
• During th e ECU Upgrade. obse rve the following precautions.
Failure to fo llo w th ese precauti ons may result in ECU damage.
ID Register
Option Treatment
Data Treatment
Inspection I Test
ECU !tapping Velffication 1
.ta•
. ., .. , .... ., .......
7.
l
Sample screen
Clise Arliltys!S
OTC
C1.1Tent08ta
ActuatiOn
Tes t
fllgf\1 Record
OllOM
I .-
0 5ciUoscope
Sl,:i;tfon
Tf!SI
~t
O
Update
Iii..
,..
...... .
Enter the Password and click OK.
13MY
13MY
13MY
13MY
8.
,_.,
I
1) DO NOT operate any other computer program.
2) DO NOT disturb or disconnect the DLC(Data Unk Connector).
3) DO NOT tum off the VCI or DO NOT disconnect VCI USB Connector.
4) DO NOT start the vehicle or turn the lG key off.
5) DO NOT operate any of the vehicles other systems(climate control. lighting,
audio. etc.)
LM
LM
LM
LM
2.4
2.4
2.4
2.4
MENU
ULEV NON IMMO : 39106/39116-2G803
ULEV IMMO: 39106/39116-2G813
SULEV NON IMMO : 39106-2G823
SULEV IMMO: 39106-2G883
IGNITION
KEY
SSB
KEY
SSB
PASSWORD
2803
2813
2823
2883
If the "Voltage is OK", select OK. If not, select CANCEL and charge the vehicle battery.
9. The remaining steps are the same as Step 7-12 of the Auto Procedure.
TSB # : 14-01-007
Page 5 of 7
SUBJECT:
TUCSON (LM) ECM & TCM UPDATE (SERVICE CAMPAIGN TS3)
GOS AUTO MODE TCM UPDATE PROCEDURE
1. From the GOS home page , select ECU Upgrade . If necessary, select the VIN.
2. Select AT as the system and then select OK.
3. Select Auto Mode and then select Next.
4. From the System tab , select AT and then select OK. The GOS will read the ROM ID . Confirm
the ROM is applicable as shown on Page 1, "ROM ID Information".
5. Update event 287.13MYLM 2.4 ACTIVE ECO ACCELERATION LOGIC IMPROVEMENT -TCM
will display. Select Upgrade.
• Mode
Auto Mode
• Current ROM ID
jTLMOC24NA 7
• Latest ROM ID
fi"LMOC24N 10
287 13MY LM 24 ACTIVE ECO ACCELERATION LOGIC IMPROVEMENT-TCM
•System
AT
a
1
Event se lection
1. Review and understand related TSB for vehic le reprogramming.
2. Select rep rogramming even t from Upgrade Event pull down menu above.
3. Click the Upgrade bu tton to begin ECU upgrade.
ID Register
Option Treatment
Data Treatment
Inspection I Test
ECU Mapping VsifiC