14-FL-004

@; HYUnDRI
nEW THlnKlnG.
nEW POSSIBILITIES.
Technical Service Bulletin
SUBJECT: I
GROUP
FUEL SYSTEM
NUMBER
14-FL-004
MODEL(S)
DATE
SANT A FE (AN)
SEPTEMBER, 2014
ECM UPDATE -AN 2.0L TURBO COLD START MISFIRE LOGIC
Description: This bulletin provides information related to an ECM software update on certain 20132014MY SANTA FE (AN) 2 .0L TURBO vehicles to update the cold start misfire logic for the following
DTCs: P0300 , P0301 , P0302 , P0303 and P0304 .
!Applicable Vehicles: 2013 - 2014MY SANTA FE (AN) 2.0L TURBO
GOS Information:
"323 .AN 2.0L TURBO COLD START LOGIC"
Warranty Information:
NOTE: Use the applicable ECM P/N listed in the ROM ID Information Table from the following
page.
Circulate To: General Manager, Service Manager, Parts Manager, Warranty Manager, Service
Advisors , Technicians , Body Shop Manager, Fleet Repair
ECM UPDATE -AN 2.0L TURBO COLD START MISFIRE LOGIC
SUBJECT:
ECM ROM ID INFORMATION TABLE:
Verify the ECM ROM ID before updating the vehicle 's software . Refer to the table below.
ROMID
Model
MY
ECM P/N
OPTION
IMMO
Previous
39100-2GBBO
2WD
YES
(Push Button Start)
39100-2GBCO
4WD
YES
(Push Button Start)
39100-2GBDO
2WD
NO
(Key Start)
39100-2GBEO
4WD
NO
(Key Start)
39100-2GBB1
2WD
YES
(Push Button Start)
BECORH2A
BECORH2B
39100-2GBC1
4WD
YES
(Push Button Start)
BECORH2A
BECORH2B
13MY
SANTA
FE
2.0L
(AN)
BDCORE3A
BDCORE3B
BDCORE5A
BDCORE5B
BDCORF2A
BDCORF3A
BDCORGOA
BDCORE3A
BDCORE3B
BDCORE5A
BDCORE5B
BDCORF2A
BDCORF3A
BDCORGOA
BDCOME3A
BDCOME3B
BDCOME5A
BDCOME5B
BDCOMF2A
BDCOMF3A
BDCOMGOA
BDCOME3A
BDCOME3B
BDCOME5A
BDCOME5B
BDCOMF2A
BDCOMF3A
BDCOMGOA
New
BDCORG01
BDCORG01
BDCOMG01
BDCOMG01
14MY
TSB #: 14-FL-004
Page 2 of 5
SUBJECT:
ECM UPDATE -AN 2.0L TURBO COLD START MISFIRE LOGIC
GENERAL PRECAUTIONS:
•
•
Connect the USB cable between the GOS and
the VCI.
Connect the 16-pin DLC connector from the
VCI into the DLC located under the driver's
side dash.
Make sure the battery icon at the bottom right of the GOS laptop shows at least 50%; if not,
charge the GOS or attach a battery charger.
•
•
•
•
Turn off all lights (Do not leave the headlight switch in auto mode) and all accessories
(including heater/air conditioner/fan , audio , heated seats , rea r defroster, etc) to ensure the
battery will not be discharged during the update .
Perform the update with the ignition key in the ON position . (Turn the ignition key to ON
position or press the Start-Stop Button two times without depressing the brake pedal) .
Do not disconnect any cables connected to the vehicle or the GOS during the update .
Do not start the engine or turn the ignition switch OFF during the update .
Confirm your GOS has the most recent version . If not, connect the GOS to an Internet port,
open the GOS home page and select "Update". Refer to instructions on hmaservice .com if
necessary.
If you encounter GOS related problems, call the GIT Helpline at 888-437-0308.
SERVICE PROCEDURE:
GOS AUTO MODE ECM UPDATE PROCEDURE
1.
2.
3.
From the GOS home page , select ECU Upgrade . If necessary, select the VIN .
Select Engine as the system and then select OK.
Select Auto Mode and then select Next.
TSB #: 14-FL-004
Page 3 of 5
SUBJECT:
4.
ECM UPDATE -AN 2.0L TURBO COLD START MISFIRE LOGIC
From the System tab , select Engine and then select OK. The GOS will read the ROM ID .
Confirm the ROM is applicable as shown on Page 2 , "ECM ROM ID Information".
NOTE: Record the ECM ROM ID in case the auto update fails and a manual update is needed .
GOS
5.
Update event "323.AN 2.0L TURBO COLD START LOGIC" will display.
Select Upgrade.
( •
Event Group
Event List
• Current ROM ID
jCMAN35"M2"" AC6A"
• Latest ROM ID
ICMAN~5" M2""AD1BS
.
Example Screen
6.
7.
8.
9.
10.
11 .
12.
13.
-
r
If the screen indicates "Voltage is OK" (voltage > 12volts), select OK. If not, select CANCEL
and charge the vehicle battery by running the engine for 10 minutes .
Updating will occur until 100% is reached on the bar graph. At the prompt, turn the ignition key
OFF for 10 seconds , then turn it ON and select OK.
The GOS will confirm that ECM update is successfully finished. Select OK.
If the ECM update was not successful , go to GOS MANUAL MODE ECM UPDATE
PROCEDURE.
Check for OTC in all systems and Erase All OTC that stored due to loss of CAN communication
during the ECM Update .
Turn OFF ignition for 10 seconds then turn ON before going to engine start.
Start the engine to confirm proper operation.
Clear OTC in the Bluelink system per instructions of TSB 12-BE-005-2.
In the event of AUTO MODE update failure:
• You must attempt MANUAL MODE . Use the ECM P/N from the vehicle's ECM
label if it is not clear from the ROM ID Table as to the correct ECM P/N to use for
your vehicle.
• Replacing an ECM without carefully documenting that a MANUAL MODE update
attempt was made may result in claims charged back.
TSB #: 14-FL-004
Page 4 of 5
SUBJECT:
ECM UPDATE-AN 2.0L TURBO COLD START MISFIRE LOGIC
GOS MANUAL MODE ECM UPDATE PROCEDURE
•
•
•
•
1.
2.
3.
4.
5.
6.
GOS Manual Mode is intended for recovery of an ECM Update should it begin but
then later fail in process in the Auto Mode .
The ECM connectors must be disconnected for 15 minutes to reset its contents
then perfo rm this Manual Mode Update .
Do not force Manual Mode if you get an error in Auto Mode that the vehicle's
current ROM ID did not apply.
It is critical to identify the correct ECM Part Number in the PASSWORD table or the
ECM may be permanently damaged. It is recommended to remove ECM and read
the part number from the label to confirm .
From the GOS home page , select ECU Upgrade . If necessary, select the VIN.
Select Engine as the system and then select OK.
Select Manual Mode and then select Next.
From the System tab , select Engine and then select OK.
Select update event "323.AN 2.0L TURBO COLD START LOGIC", then select Upgrade.
Be certain to enter the exact appropriate password from the table below and select OK.
PASSWORD
COMMENTS
OMA 2.0 IMMO 39100-2GBB0/2GBCO
9120
Push Button Start
OMA 2.0 IMMO 39100-2GBB1/2GBC1
9121
Push Button Start
OMA 2.0 NON IMMO 39100-2GB00/2GBEO
9122
Key Start
MENU
7.
The remaining steps are the same as Steps 6-13 of the Auto Procedure.
TSB # : 14-FL-004
Page 5 of 5