13-AT-012-2

GROUP
HVUnDRI
~
-
I nEWTHlnKlnG.
nEW POSSIBILITIES.
NUMBER
AUTOMATIC
TRANSMISSION
MODEL
DATE
Technical Service Bulletin
13-AT-012-2
OCTOBER
2013
Tucson (LM), Santa Fe (CM/AN/NC),
Sonata (YF/YF HEV), El antra
(UD/MD/GD/JK), Accent (RB), Azera
(TG/HG) , Veloster Turbo (FS)
AUTOMATIC TRANSAXLE (6-SPEED)
OIL TEMPERATURE SENSOR OTC P0711, P0712 & P0713
SUBJECT:
This TSB supersedes bulletin 13-AT-012-1 to add Op Codes.
Description: Do not replace the transaxle for the OTC listed below. Instead , follow the repair
procedure and replace the related part.
Applicable
Vehicles:
Model Years
Model
2010 -
Tucson (LM) & Santa Fe (CM)
2011 -
Sonata (YF/HEV) , Elantra (UD/MD) & Azera (TG )
2012 -
Accent (RB), Azera (HG)
2013-
Veloster Turbo (FS) , Elantra Coupe (JK) , Elantra GT (GD)
and Santa Fe (AN/NC)
-
OTC LIST:
OTC
DESCRIPTION
P0711
Transmission Fluid Temperature Sensor - Rationality check
P0712
Transmission Fluid Temperature Sensor - Circuit Low Input
P0713
Transmission Fluid Temperature Sensor - Circuit High Input
Circulate To : Service Manager, Warranty Manager, Service Advisors, Technicians , Fleet Repair
ATM OIL TEMPERATURE SENSOR OTC P0711, P0712 & P0713
SUBJECT:
PARTS INFORMATION:
*NOTE
The oil temperature sensor has been integrated with the internal harness from early
March, 2013. The oil temperature sensor is not available separately for these models.
Previous (separate parts)
Oil temperature sensor
and internal harness
MODEL
ENGINE
OIL TEMPERATURE
SENSOR
HARNESS
PLASTIC OIL PAN
GASKET
2012- Accent (RB)
1.6L
46386-38000
46307-38***
45282-26100
2011 Azera (TG)
3.3L/3.8L
46386-38000
46307-38***
45283-38010
2012- Azera (HG)
3.3L
46386-38000
46307-38***
45283-38010
2011- Elantra (MD/UD)
1.8L
46386-38000
46307-38***
45282-26100
2013- Elantra Coupe (JK)
1.8L
46386-38000
46307-38***
45282-26100
2013- Elantra GT (GD)
1.8L
46386-38000
46307-38***
45282-26100
2010-12 Santa Fe (CM)
2.4L
46386-38000
46307-38***
45282-26100
2010-12 Santa Fe (CM)
3.5L
46386-38000
46307-38***
45283-38010
2013- Santa Fe (AN)
2.0L
46386-38000
46307-38***
45283-38010
2013- Santa Fe (AN)
2.4L
46386-38000
46307-38***
45283-38810
2013- Santa Fe (NC)
3.3L
46386-38000
46307-38***
45283-38010
2011- Sonata Turbo (YF)
2.0L
46386-38000
46307-38***
45283-38010
2011- Sonata (YF)
2.4L
46386-38000
46307-38***
45283-38810
2011- Sonata HEV (YF HEV)
2.4L
46386-38000
46307-38***
45283-30100
2010- Tucson (LM)
2.0L/2.4L
46386-38000
46307-38***
45283-38810
2013- Veloster Turbo (FS)
1.6L
46386-38000
46307-38***
45283-38810
TSB #: 13-AT-012-2
Page 2 of 10
SUBJECT:
ATM OIL TEMPERATURE SENSOR OTC P0711, P0712 & P0713
WARRANTY INFORMATION - REPLACE OIL TEMPERATURE SENSOR AND HARNESS (SEPARATE):
MODEL
OPCODE
OPERATION
OP TIME
201 2- Accent (RB)
1.3
201 1 Azera (TG )
1.9
201 2- Azera (HG)
1.6
NATURE
CODE
CAUSE
CODE
46307-xxxxx
(See Parts
Catalog)
N69
C15
1.5
2011- Elantra (MD/UD)
Auto
transm ission
valve body
harness
2013- Elantra Coupe (JK)
2013- Elantra GT (GD)
2010- Santa Fe (CM)
CAUSAL
PART
46307ROO
201 3- Santa Fe (NC)
1.5
1.9
(includes time
for oil
temperature
sensor)
2013- Santa Fe (AN)
1.5
1.9
1.9
2010- Tucson (LM)
1.5
201 3- Veloster Turbo (FS)
1.5
2011- Sonata (YF)
1.5
1.5
2011- Sonata (YF HEV)
ALL
46307RH1
Additional
1.5
46307RQO
GOS Operation
0.3
WARRANTY INFORMATION - REPLACE HARNESS WITH INTEGRATED OIL TEMPERATURE SENSOR:
MODEL
OPCODE
OPERATION
OP TIME
2012- Accent (RB)
1.3
2012- Azera (HG)
1.6
2011- Elantra (MD/UD)
1.5
2013- Elantra Coupe (JK)
1.5
2013- Elantra GT (GD)
2013- Santa Fe (AN)
46308ROO
2013- Santa Fe (NC)
Valve body
harness
equipped with
oil temperature
sensor
1.5
1.9
1.9
2010- Tucson (LM)
1.5
2013- Veloster Turbo (FS)
1.5
2011- Sonata (YF)
1.5
CAUSAL
PART
NATURE
CODE
CAUSE
CODE
46307-xxxxx
(See Parts
Catalog)
N69
C15
1.5
2011- Sonata (YF HEV)
ALL
TSB #: 13-AT-012-2
46308RH1
Additional
1.5
46308RQO
GOS Operation
0.3
Page 3 of 10
SUBJECT:
ATM OIL TEMPERATURE SENSOR DTC P0711, P0712 & P0713
SERVICE PROCEDURE:
1.
Using a GOS, check for OTC in the "Automatic Transaxle" menu . Record the OTC and
description. Delete the OTC .
2.
From the GOS , select the following parameters. Drive the vehicle and monitor the sensors .
• Vehicle and A/T menu .
• "Current Data"
• Oil temperature sensor.
Repair
Preparation
.C:: . . .
-
I
Senso r Name
621 Oil Temper111ure Sensor
OSelect a Sensor Data
item to view its relative
information.
0
Input Speed(PG..A)
0
Output Speed(PG.B)
Cl
Shift Lever Switch
0
··El
D RPIA
D RPtA
p
Pfll
0 Current Gea r
D Next Gear Position
0 Engine RPM
D Gear Ratio
D Shift Contro l Soleno id Valve
0 Shift Control Solenoid Valve
D Shift Conrrol Solenoid Va lve
D Shift Control Solenoid Valve
O Shift Contro l Solenoid Va lve
.....
Value I Unit
104 'F
'
0
0.0
0
0
0
D
OFF
OFF
0
0
OFF
0
0
0.0
OFF
OFF
OFF
8.2
0.0
OFF
A(UDIB)
B(l.618)
C.{.35Rrq
D(OO/q
E(SS.A)
Shift Control Solenoid Valve F(SS -8)
D Pressure Contro l Solenoid Valve(VFS) •A·
D Torque Converter Outch Solenoid Valve
0 Torque Co nverter Clutch Control State
D Torq ue Converter Clutch Sllp
0 Vehicle Speed
O Engine Torque
O Sports Uocle Select
D Sports Mode Up Switch
D Sports Mode Down Switch
D Throttle Position Senso r Angle
D Accelerator Peda l Position Senso r
n Brake Switch
Ac!uatlon
l est
FliglllRecoid
OVOM
I
RPM
mA
mA
mA
mA
mA
mA
RPM
MPH
•
••
~~
·no
0 "' scope
Shm.JaliOO
Test
3.
If the sensors show:
• Continuous and changing output while driving , the wiring currently has no open/short
circuits. Go to Step 5.
• No output or unchanging output, go to Step 4.
4.
Visually check the wiring harness between the PCM and transmission for a damaged wire or
short circuit to ground . Check for a damaged pin or pin not fully inserted into the connector.
• If damage exists, repair or replace the ECM control harness and drive the vehicle to confirm
the repair.
• If no damage , go to Step 5.
5.
Refer to the OTC recorded in Step 1 and follow the repair procedure shown below:
P0711
P0712
P0713
OTC
Transmission Fluid Temperature Sensor Rationality check
Transmission Fluid Temperature Sensor Circuit Low Input
Transmission Fluid Temperature Sensor Circuit Hiqh Input
TSB #: 13-AT-012-2
REPAIR PROCEDURE
Go to Step 6 and replace the oi l
temperature sensor and valve body
harness
Page 4 of 10
SUBJECT:
ATM OIL TEMPERATURE SENSOR OTC P0711 , P0712 & P0713
6.
Remove the battery and battery tray .
7.
Remove the undercover below the transmission .
8.
Drain the radiator and remove the lower radiator hose from the radiator.
Drain the ATF .
9.
Use a screwdriver to release the tab and
remove the solenoid connector on top of the
case .
Remove the bolt that secures the connector
and push the connector into the transmission.
Disconnect the vent hose at the top of the oil
pan.
10. Remove the oil pan bolts and remove the pan .
-
11:::, CAUTION
Use rubber hammer to tap the oil pan
cover on a corner until the cover is
loose.
11 . Use a small screwdriver to pry the connector
from the oil temperature sensor (except for
vehicles with integrated temperature sensor
and harness) .
TSB # : 13-AT-012-2
Page 5 of 10
SUBJECT:
ATM OIL TEMPERATURE SENSOR OTC P0711, P0712 & P0713
12. Remove three bolts to the solenoid valve
connector.
13. Pull the solenoid connector outward and move
the connector out of position.
14. Remove the bolt that secures the detent spring
and remove the spring .
Torque: 8-11 lb.ft (1 .2-1 .6 kgf.m)
TSB # : 13-AT-012-2
Page 6 of 10
SUBJECT:
15.
ATM OIL TEMPERATURE SENSOR DTC P0711, P0712 & P0713
Remove 8 bolts in the order shown and
remove the valve body.
16. Use a screwdriver to depress the locking tab
and pull outward on the connector to the input/
output speed sensor.
17.
Remove two bolts that secure the valve body
harness to the case.
Pull the connector downward out of the case.
Install a new harness and insert the connector
into the case. Attach the retainer and bolt on
top of the case as shown in Step 9.
Install the bolts that secure the harness .
Torque: 6-7 lb.ft (0.9-1.0 kgf.m)
TSB #: 13-AT-012-2
Page 7 of 10
SUBJECT:
ATM OIL TEMPERATURE SENSOR DTC P0711, P0712 & P0713
18. Confirm two o-rings are installed correctly in
the case.
Reconnect the input and output speed sensor
connector to the harness .
19. Align the manual shaft to the shift lever and
install the valve body.
20.
Install the valve body bolts and torque the bolts
to specification in the order shown.
Toque: 6-7 lb.ft (0.9-1.0 kgf.m)
TSB #: 13-AT-012-2
Page 8 of 10
SUBJECT:
ATM OIL TEMPERATURE SENSOR OTC P0711, P0712 & P0713
21 . Reconnect the solenoid harness to the
solenoids and oil temperature sensor.
Install the bolts to the solenoid harness
connector and torque to specification .
Torque : 6-7 lb.ft (0 .9-1 .0 kgf.m)
22 . STEEL OIL PAN:
Apply Permatex Ultra Gray Sealer or Hyundai
Ultra Gray Gasket Sealer, P/N 00232-19039,
to the oil pan and reinstall the pan .
PLASTIC OIL PAN:
Install a new gasket to the oil pan , reinstall the
pan and tighten the bolts to specification .
Torque: 6-7 lb.ft (0 .9-1.0 kgf.m)
See part number list on Page 2.
23.
Remove the transaxle fill plug .
Filling and checking of fluid level is
done through valve body side cover
Use a funnel to add approximately 5-6 quarts of
SP4-M ATF through the fill plug opening . Reinstall
the fill plug.
Attach the GOS to the DLC and select vehicle , A/T
menu , Current Data and "Oil Temperature Sensor".
Start the engine and shift to Park. When the ATF is
122°F-140°F (50-60°C) , remove the level
checking plug . The level is correct when oil flows
out of the level checking plug in a thin steady
stream.
Collect and dispose of any excess fluid in
accordance with local regulations.
TSB #: 13-AT-012-2
I
Fill Plug shown
I Level Checking Plug
ATF TEMPERATURE= 122 - 140F (50- 60C)
SHIFT LEVER IN "P" AND ENGINE RUNNING
Page 9 of 10
ATM OIL TEMPERATURE SENSOR OTC P0711 , P0712 & P0713
SUBJECT:
24 . Attach the GOS and erase all OTC .
25 . Clear OTC in the Bluelink system per instructions of TSB 12-BE-005-2 .
26 . Drive the vehicle for two drive cycles (two key-on to key-off driving cycles) .
• If the OTC do not occur again , return the vehicle to the customer.
• If the OTC return , perform the following repairs :
P07 11
P0712
P071 3
27 . •
•
•
OTC
Transmission Fluid Temperature Sensor Rationality check
Transmission Fluid Temperature Sensor
- Circuit Low Input
Transmission Fluid Temperature Sensor Circuit Hiqh Input
•
•
REPAIR PROCEDURE
Repair or replace the control harness
between the PCM and the transmission .
Drive the vehicle for two drive cycles . If
the OTC return again , replace the PCM .
Attach the GOS and erase all OTC.
Clear the OTC in the Bluelink system per instructions of TSB 12-BE-005-2.
Drive the vehicle for two drive cycles (two key-on to key-off driving cycles). If the OTC do not
occur again , return the vehicle to the customer.
TSB # : 13-AT-012-2
Page 10 of 10