ARTICLE 64634

Printable Version
ROADSTER High Windshield Dropping on Bumpy Road (ST)_000064634_TST61Y014S09_en
Rate This Article
(Average Rating: No Rating)
Version 2
Rate This Article
(Average Rating: No Rating)
Version 2
Language
!U!!ic!i,!,
Summary:
Some customers have reported that wi h the installa ion of the high windshield for PAC that in some certain driving conditions the windshield drops.
Type:
General
TST Detail:
The solu ion consists in the installa ion of 219800352 - High Windshield Refurbish Kit springs to increase he pre-load on the balls and slide rail.
You will notice the windshield adjustment is much stiffer. Show he customer how to properly adjust the height of he windshield using both hands and pulling/pushing evenly.
Attachment:
First Published By: Dany Davey on 2013-1 0-30
Last Modified By: Dany Davey on 2014-09-05
Article_Detail_TST 3 htm(2014-10- 15 10:45:42 AM]
Show Properties
!
Language U!!icli,!,
Show Properties
Printable Version
ROADSTER KIT - High Windshield Refurbish Kit 219800352_000096028_INS61Y014S88_en
Rate This Article
(Average Rating: No Rating)
Version 1
Rate This Article
Produ ct:
Roadster
Project no:
rsi2014·030
In struction S heet PIN:
219800353
(Average Rating: No Rating)
Version 1
Language
!U!!ic!i,!,
Show Properties
!
Language U!!icli,!,
Show Properties
Revision no :
Revision date:
High Windshield Refurbish Kit (Kit PIN : 219800352)
Item covered :
PRIOR TO INSTALLATION, PLEASE VERIFY IF A REVISED VERSION OF THIS INSTRUCTION SHEET IS AVAILABLE ON KNOWLEDGE CENTER.
The following symbols may be used in t his document:
CAUTION: Indicates an instruc ion which, if not followed, could severely damage vehicle components or other property.
•/11111•@ Indicates an instruction which, if not followed, could severely damage vehicle components or other property.
A
WARNING
• This kit is designed for specific applicable models only (authorized BRP dealers will confinn model(s)). It is not recommended for units other than the one (those) for which it was sold.
• This instruc ion sheet MUST be given to the purchaser.
• Should removal of a locking device (e.g. lock tabs, self-locking fasteners, etc.) be required when undergoing disassembly/assembly, always replace with a new one.
• Torque wrench tightening specifications must strictly be adhered to.
NOTE: The illustrations in this document show typical construction of he different assemblies and may not reproduce the full detail or exact shape of the parts; however, hey represent parts that have the same or si milar function.
Installation time is approximately 0.4 hour.
ICON LEGEND
Icon
om
Article_Detail_ Instruction_Sheet 4htm[2014- 10.15 10:45:12 AM)
indicates
Parts to be discarded
Parts kept for reinstallation
PULLEY FLANGE CLEANER (P/N 413 711 809)
XPS SYNTHETIC GREASE (P/N 293 550 010)
ITEMS IN KIT
Item
Description
Part Number
Quantity
P1
Position plate
705 005 459
2
P2
Slider
705 005 275
4
P3
Ball
705 001 705
4
Standard Spring for factory windshield
705 005 277
4
Yellow spring for use with PAC high windshield (P/N 219 400 354)
705 009 458
4
M6 elastic nut
232 561 414
6
P4
P5
INSTRUCTIONS
Article_Detail_Instruction_Sheet 4 htm[2014-10-15 10:45:12 AM]
,
'
@
2X
Jj
Article_Detail_Instruction_Sheet 4 htm[2014-10-15 10:45:12 AM]
Right hand side shown
NOTE: Hold together when removing final screw [3].
Article_Detail_Instruction_Sheet 4 htm[2014-10-15 10:45:12 AM]
@ 3X . . 10 : 2 N•m
Repeat procedure on left hand side.
Article_Detail_Instruction_Sheet 4 htm[2014-10-15 10:45:12 AM]
@ 4X•4.5±0.5 N•m
,
,...a
\
@
2X
Article_Detail_Instruction_Sheet 4 htm[2014-10-15 10:45:12 AM]
\
@
4 X .....
2.5 ± 0 .2 N•m
Article_Detail_Instruction_Sheet 4 htm[2014-10-15 10:45:12 AM]