TSBENG147
Service Bulletin Details
Public Details for: TSBENG147
Tsb: data collection: extract california emissions data from ecu (dC1501) - this bulletin provides information related to extracting ?In use performance tracking? Emissions data from the engine control unit (ecu) of certain vehicles sold in
- 2015 -
Models from 2015
2015 KIA FORTE |
2015 KIA K900 |
2015 KIA OPTIMA |
2015 KIA OPTIMA HYBRID |
2015 KIA RIO |
2015 KIA SORENTO |
2015 KIA SOUL |
2015 KIA SPORTAGE |
GROUP Engine MODEL 2015MY Multiple Models (see table on Pg. 17) NUMBER 147 DATE July 2015 TECHNICAL SERVICE BULLETIN SUBJECT: DATA COLLECTION: EXTRACT CALIFORNIA EMISSIONS DATA FROM ECU (DC1501) This bulletin provides information related to extracting “in use performance tracking” emissions data from the Engine Control Unit (ECU) of certain vehicles sold in California. The California Air Resources Board (CARB) requires the emissions data from vehicles with a minimum of 3,000 accumulated miles without reprogramming or resetting. To facilitate collection of this data at the dealer level, GDS/KDS screenshots will allow the capture of relevant parameters. NOTICE IF THE VEHICLE MEETS THE CRITERIA BELOW, CALIFORNIA DEALERS MUST PERFORM THIS DATA COLLECTION ON VEHICLES WHENEVER AN AFFECTED VEHICLE IS IN THE SHOP FOR ANY MAINTENANCE OR REPAIR. THIS DATA COLLECTION DOES NOT APPLY TO VEHICLES OR DEALERS OPERATING OUTSIDE OF CALIFORNIA. For vehicles listed on DCS as requiring this procedure, follow the instructions in this bulletin after confirming that the following criteria are met: WebDCS shows this as an open Data Collection code DC1501A model) for the vehicle. U (depending on NOTICE Note that as sufficient data is collected, individual line items per model may be closed without updates to the TSB. Once a line item is closed on DCS, no further data collection is required. Data collections initiated after a line item is closed are subject to chargeback. Vehicle has more than 3000 miles on its odometer. Vehicle repair history does not show battery replacement/disconnection/reset or an ECU Update done in the last 3000 miles, because IUMPR (In Use Monitor Performance Ratio) data would have been cleared by such an event. Vehicle does not have a check engine light ON. File Under:Circulate To: x General Manager x Service Advisor(s) x Service Manager x Parts Manager x Technician(s) x Body Shop Manager Fleet Repair Page 2 of 18 SUBJECT: DATA COLLECTION: EXTRACT CALIFORNIA EMISSIONS DATA FROM ECU (DC1501) NOTICE If vehicle meets above criteria, collect data prior to any other campaign or repairrelated activities. GDS Service Procedure: (For KDS procedure, proceed to Page 7) 1. Open the engine compartment and locate the Vehicle Emission Control Information label. Write down the “Group” number for later entry into the form. 2. With the ignition key ON, insert the VCI into the DLC and turn on the GDS. Access the GDS vehicle identification number (VIN) screen and configure the vehicle using the VIN AUTO DETECT Function. NOTICE 3. GDS must be updated to version N-K-01-15-0000, or later, to properly collect data. GDS must be connected to the internet to submit data. Choose Engine and Click on OK. NOTICE Screens shown in this bulletin are for demonstration ONLY purposes and will vary depending on the vehicle. TSB: ENG 147 Multiple Models July 2015 Page 3 of 18 SUBJECT: DATA COLLECTION: EXTRACT CALIFORNIA EMISSIONS DATA FROM ECU (DC1501) 4. Select CARB Diagnosis tab. OBD-II under the 5. Click on IN USE Performance Ratio at the bottom left of the screen. NOTICE If all values indicate "Not Supported" or "0", check to make sure you have GDS software version N-K-01-15-0000 or later. If the software version is correct, and all values show "Not Supported" or "0", the vehicle will not qualify for this data collection, as it may have received a recent ECM Update or battery replacement/reset of the data values. 6. Click on Gasoline and then click the Expand button at the top right corner of the IN USE Performance Ratio window. Expand Button Select Gasoline TSB: ENG 147 Multiple Models July 2015 Page 4 of 18 SUBJECT: 7. DATA COLLECTION: EXTRACT CALIFORNIA EMISSIONS DATA FROM ECU (DC1501) Click Gasoline. Capture button. Then, click the NOTICE Make sure to capture the entire screen. If only part of the screen is displayed, first click the “Expand” button as described in step 6. 8. Select Entire GDS Area and click Send to file. The GDS will set up a destination folder and file name to save the captured screenshot. Change the file name to include the model/engine, the last 6 digits of the VIN and the date (mmddyyyy), as shown below. Example: XM33L_576681_06092015 (Model & Eng.) (VIN) (mmddyyyy) 9. After saving the Feedback button. file, click on NOTICE GDS must be connected to the internet to submit data. TSB: ENG 147 Multiple Models July 2015 Capture Button Page 5 of 18 SUBJECT: 10. DATA COLLECTION: EXTRACT CALIFORNIA EMISSIONS DATA FROM ECU (DC1501) Enter all the information requested in the form, including your name and email address. Additionally, enter the following information: • For System, enter Engine • For Subject, enter Data Collection • In the Description area, ○ Type Group: followed by the group number from the Vehicle Emission Control Information Label collected in step 1. ○ Add current odometer mileage. ○ Add RO#. 11. GROUP:XXXXXXXXXXX CURRENT ODOMETER MILEAGE: XXXXXX RO#: XXXXXXXXXXX To attach the data to the feedback form, click on the Browse button. NOTICE Ensure that you attach the correct files. Incorrect attachments render data submissions useless and are subject to a charge-back of the warranty claim. 12. GROUP:XXXXXXXXXXX CURRENT ODOMETER MILEAGE: XXXXXX RO#: XXXXXXXXXXX Use the path shown below to navigate to the destination folder and file created in step 8. Navigate to: Local Disk (C:) > gvciData > Record Click on the folder for the vehicle i.e.,"Sorento (XM)." Click on the folder containing the vehicle VIN, as shown. TSB: ENG 147 Multiple Models July 2015 Page 6 of 18 SUBJECT: 13. DATA COLLECTION: EXTRACT CALIFORNIA EMISSIONS DATA FROM ECU (DC1501) Select the correct file and click the Open button to attach it to the feedback form. NOTICE XM33L_576681_ 06092015 Ensure that you attach the correct files. Incorrect attachments render data submissions useless and are subject to a charge-back of the warranty claim. 14. When the file name appears in the attachment field, and all the information has been entered, click on the Submit button. NOTICE GROUP:XXXXXXXXXXX CURRENT ODOMETER MILEAGE: XXXXXX RO#: XXXXXXXXXXX GDS must be connected to the internet to submit data. XM33L_576681_06092015 TSB: ENG 147 Multiple Models July 2015 Page 7 of 18 SUBJECT: DATA COLLECTION: EXTRACT CALIFORNIA EMISSIONS DATA FROM ECU (DC1501) KDS Service Procedure: 1. Open the engine compartment and locate the Vehicle Emission Control Information label. Write down the “Group” number for later entry into the form. 2. With the ignition key ON, insert the VCI II into the DLC and swipe down on the Vehicle Selection area to identify the vehicle. NOTICE Screens shown in this bulletin are for demonstration ONLY purposes and will vary depending on the vehicle. 3. Select AUTO VIN and click OK. TSB: ENG 147 Multiple Models July 2015 Page 8 of 18 SUBJECT: DATA COLLECTION: EXTRACT CALIFORNIA EMISSIONS DATA FROM ECU (DC1501) 4. Once back on the Screen, select OBD-II. KDS Home 5. Select IN USE Performance Ratio > Gasoline. TSB: ENG 147 Multiple Models July 2015 Page 9 of 18 SUBJECT: DATA COLLECTION: EXTRACT CALIFORNIA EMISSIONS DATA FROM ECU (DC1501) 6. Select the Screen Capture button to save a screenshot of the data. 7. Select the Save button to save the screenshot. 8. The KDS will set up a destination folder and file name to save the screenshot. Change the file name to include the model/engine, the last 6 digits of the VIN and the date (mmddyyyy), as shown below. Example: XM33L_576681_06092015 (Model & Eng.) (VIN) (mmddyyyy) 9. Select OK to save the image. XM33L_576681_06092015 TSB: ENG 147 Multiple Models July 2015 Page 10 of 18 SUBJECT: DATA COLLECTION: EXTRACT CALIFORNIA EMISSIONS DATA FROM ECU (DC1501) Select the Return Arrow on the screen and select the HOME button to return to the KDS Home Screen. 10. NOTICE Steps 11~17 will need to be performed only once to properly set up KDS for this Data Collection procedure. If Chrome is already the default KDS browser, proceed to step 12. If access to the External Storage has already been added to the file manager, proceed to step 18. 11. First, set Chrome as the default Browser. If this step has been previously done, proceed to step 12. If not, access: Configuring Browser for Techline Cases on KGIS for more information. 12. Once Chrome is set as the default browser, navigate to the KDS Home Screen and select Feedback. NOTE: steps 12~17 will add access to Internal and External Storage to the file manager. TSB: ENG 147 Multiple Models July 2015 Page 11 of 18 SUBJECT: DATA COLLECTION: EXTRACT CALIFORNIA EMISSIONS DATA FROM ECU (DC1501) 13. Select one of the Choose File buttons at the bottom of the screen. 14. Select Documents. 15. Select the Settings button on the upper right hand corner. TSB: ENG 147 Multiple Models July 2015 Page 12 of 18 SUBJECT: DATA COLLECTION: EXTRACT CALIFORNIA EMISSIONS DATA FROM ECU (DC1501) 16. Check the box for Show advanced device opt. and Show file size, as shown. 17. Access to Internal and External Memory is now available on the left hand side of the file manager. External Internal 18. Return to the KDS Home Screen and select Feedback (Pg. 10, step 12). Enter all the information requested in the form, including your name and email address. Additionally, enter the following information. • For System, enter Engine • For Subject, enter Data Collection • In the Description area, ○ Type Group: followed by the group number from the Vehicle Emission Control Information Label collected in Pg. 7, step 1. ○ Add current odometer mileage. ○ Add RO#. NOTICE Make sure the email address is entered correctly or the Feedback form will fail to submit. TSB: ENG 147 Multiple Models July 2015 GROUP:XXXXXXXXXXX CURRENT ODOMETER MILEAGE: XXXXXX RO#: XXXXXXXXXXX Page 13 of 18 SUBJECT: DATA COLLECTION: EXTRACT CALIFORNIA EMISSIONS DATA FROM ECU (DC1501) 19. To attach the screenshots to the report, select Choose File. 20. Select Documents. 21. Select External Storage > Android. TSB: ENG 147 Multiple Models July 2015 Page 14 of 18 SUBJECT: DATA COLLECTION: EXTRACT CALIFORNIA EMISSIONS DATA FROM ECU (DC1501) 22. Select data. 23. Scroll down gitauto.GDSM. 24. Select files. and select TSB: ENG 147 Multiple Models July 2015 Page 15 of 18 SUBJECT: DATA COLLECTION: EXTRACT CALIFORNIA EMISSIONS DATA FROM ECU (DC1501) 25. Select mvcidata. 26. Select Record. 27. Select the vehicle model. Sorento (XMa) June 15 28. Select the VIN. 5XYKWDA7XEG437824 June 15 TSB: ENG 147 Multiple Models July 2015 Page 16 of 18 SUBJECT: 29. DATA COLLECTION: EXTRACT CALIFORNIA EMISSIONS DATA FROM ECU (DC1501) Select the Screenshot. 5XYKWDA7XEG437824 XM33L_576681_06092015 June 15 30. Select Submit. NOTICE Ensure that you attach the correct files. Incorrect attachments render data submissions useless and are subject to a charge-back of the warranty claim. TSB: ENG 147 Multiple Models July 2015 GROUP:XXXXXXXXXXX CURRENT ODOMETER MILEAGE: XXXXXX RO#: XXXXXXXXXXX 1.21MB Page 17 of 18 DATA COLLECTION: EXTRACT CALIFORNIA EMISSIONS DATA FROM ECU (DC1501) SUBJECT: AFFECTED PRODUCTION RANGE: Model Production Range Cadenza 3.3L ULEV, Forte 1.6L ULEV, Forte 1.8L SULEV, Forte 1.8L ULEV, Forte 2.0L SULEV, Forte 2.0L ULEV, K900 5.0L ULEV, Optima 2.0L ULEV, Optima 2.4L SULEV, Optima 2.4L ULEV, Optima HEV 2.4L ULEV, Rio 1.6L ULEV, Sedona 3.3L ULEV, Sorento 2.4L ULEV, Sorento 3.3L ULEV, Soul 1.6L ULEV, Soul 2.0L ULEV, Sportage 2.0L ULEV, Sportage 2.4L SULEV and Sportage 2.4L ULEV 2015MY 2015MY DATA COLLECTION WARRANTY CLAIM INFORMATION: NOTICE As sufficient data is collected, individual line items per model may be closed without updates to the TSB. Once a line item is closed on DCS, no further data collection is required. Data collections initiated after a line item is closed are subject to charge-back. Campaign ID Claim Type Causal P/N Qty. N Code C Code DC1501A DC1501B DC1501C DC1501D DC1501E DC1501F DC1501G DC1501H DC1501I DC1501J DC1501K DC1501L DC1501M V 100CA EM999 0 N99 C99 Repair Description Labor Op Code Extract ECU data: Cadenza 3.3 ULEV Extract ECU data: FORTE 1.6 ULEV Extract ECU data: FORTE 1.8 SULEV Extract ECU data: FORTE 1.8 ULEV Extract ECU data: FORTE 2.0 SULEV Extract ECU data: FORTE 2.0 ULEV Extract ECU data: K900 5.0 ULEV Extract ECU data: OPTIMA 2.0 ULEV Extract ECU data: OPTIMA 2.4 SULEV Extract ECU data: OPTIMA 2.4 ULEV Extract ECU data: OPTIMA HEV 2.4 ULEV Extract ECU data: RIO 1.6 ULEV Extract ECU data: SEDONA 3.3 ULEV Time Replacement P/N Qty. 0.3 M/H N/A 0 15VG33U1 15TD16U1 15TD18S1 15TD18U1 15TD20S1 15TD20U1 15KH50U1 15TF20U1 15TF24S1 15TF24U1 15HY24U1 15UB16U1 15YP33U1 TSB: ENG 147 Multiple Models July 2015 Page 18 of 18 SUBJECT: DATA COLLECTION: EXTRACT CALIFORNIA EMISSIONS DATA FROM ECU (DC1501) DC1501N DC1501O DC1501P DC1501Q DC1501R DC1501S DC1501T DC1501U Extract ECU data: SORENTO 2.4 SULEV Extract ECU data: SORENTO 2.4 ULEV Extract ECU data: SORENTO 3.3 ULEV Extract ECU data: SOUL 1.6 ULEV Extract ECU data: SOUL 2.0 ULEV Extract ECU data: SPORTAGE 2.0 ULEV Extract ECU data: SPORTAGE 2.4 SULEV Extract ECU data: SPORTAGE 2.4 ULEV 15XM24S1 15XM24U1 15XM33U1 15PS16U1 15PS20U1 15SL20U1 15SL24S1 15SL24U1 To ensure proper claim processing, enter VIN in DCS and allow the system to auto populate claim fields. NOTICE VIN inquiry data for this repair is provided for tracking purposes only. Kia retailers should reference DC1501 when accessing the WebDCS system. TSB: ENG 147 Multiple Models July 2015