K434NAS2

TECHNICAL BULLETIN
K434NAS2
07 OCT 2016
© Jaguar Land Rover North America, LLC
NOTE: The information in Technical Bulletins is intended for use by trained, professional Technicians with the knowledge, tools,
and equipment required to do the job properly and safely. It informs these Technicians of conditions that may occur on some
vehicles, or provides information that could assist in proper vehicle service. The procedures should not be performed by
'do-it-yourselfers'. If you are not a Retailer, do not assume that a condition described affects your vehicle. Contact an authorized
Jaguar service facility to determine whether this bulletin applies to a specific vehicle.
Changes are highlighted in gray
SECTION: 303-00
Service Action: Malfunction Indicator Lamp (MIL) Illuminated With P025C-11
Stored
AFFECTED VEHICLE RANGE:
XE (X760)
Model Year:
2016-2017
VIN:
900116-963396
Assembly Plant: Solihull
XF (X260)
Model Year:
2016-2017
VIN:
Y00070-Y39830
Assembly Plant: Castle Bromwich
F-PACE (X761)
Model Year:
2017
VIN:
045068-077232
Assembly Plant: Solihull
V6 S/C 3.0L Petrol
V6 S/C 3.0L Petrol
V6 S/C 3.0L Petrol
MARKETS:
NAS
CONDITION SUMMARY:
Situation: An issue has been identified on a limited number of vehicles within the listed Affected Vehicle Range
which may experience a Malfunction Indicator Lamp (MIL) being illuminated. Diagnosis may identify P025C-11
Diagnostic Trouble Code (DTC) which indicates a short circuit to ground on the Powertrain Control Module (PCM)
and Fuel Pump Driver Module (FPDM) communication line.
Action: Retailers are required to HOLD affected new vehicles that are within your control and refrain from releasing
the vehicles for new vehicle sale pending completion of the Service Instruction detailed in this Technical Bulletin.
Unsold vehicles should have this performed as part of the Pre-Delivery Inspection (PDI) process but must have it
completed prior to vehicle handover to the customer.
Affected vehicles already in the hands of customers should be updated at the next available opportunity.
PARTS:
No parts required.
SPECIAL TOOLS:
NOTE: The active programming hyperlink has been removed from this publication. Once the technical problems
with this feature have been resolved for this publication when viewed on SDD, the hyperlink will be restored.
Jaguar Land Rover-approved Midtronics Battery Power Supply
Jaguar Land Rover-approved diagnostic tool with latest SDD software and Calibration File
WARRANTY:
NOTE: Check DDW to ensure that a vehicle is affected by this program prior to undertaking any rework action.
At the time of confirming a booking for vehicle repair, ensure that all outstanding Recalls and Service Actions are
identified to ensure the correct parts are available and adequate workshop time is allocated for repairs to be completed
at one visit.
Warranty claims must be submitted quoting Program Code K434 together with the relevant Option Code from the
table. SRO and parts information is included for information only. The Option Code(s) that allows for the drive in / drive
out allowance can only be claimed if the vehicle is brought back into the workshop for this action alone to be
undertaken.
This program is valid for a limited time only. Warranty claims with a repair date prior to the 30 September 2018
closure date must be submitted or payment within 30 calendar days of completion of the repair.
Repair procedures are under constant review and therefore times / prices are subject to change; those quoted here
must be taken as guidance only. Refer to TOPIx to obtain the latest repair time.
PROGRAM CODE OPTION CODE
K434
B
DESCRIPTION
SRO
Configure the PCM
86.99.26
TIME (HOURS) PARTS/SUNDRY CODE QTY./VALUE
0.20
-
-
K434
C
Configure the PCM
Drive in/drive out
86.99.26
0.20
0.20
-
-
10.10.10
Normal Warranty policies and procedures apply.
* - an allowance has been provided to cover the cost.
SERVICE INSTRUCTION:
CAUTION: A Jaguar Land Rover-approved Midtronics battery power supply must be connected to the vehicle
battery during diagnosis / module programming.
CAUTION: Ensure all ignition ON/OFF requests are carried out; failure to perform these steps may cause damage
to control modules in the vehicle.
NOTE: The Jaguar Land Rover-approved diagnostic tool must be loaded with SDD147.00 v.249 (or later).
NOTE: The active programming hyperlink has been removed from this publication. Once the technical problems
with this feature have been resolved for this publication when viewed on SDD, the hyperlink will be restored.
1. Connect the Jaguar Land Rover-approved Midtronics battery power supply to the vehicle battery.
2. Turn ignition ON (engine not running).
3. Connect the Jaguar Land Rover-approved diagnostic tool to the vehicle and begin a new session.
4. Follow the on-screen prompts, allowing the diagnostic tool to read the VIN and identify the vehicle and initiating
the data collect sequence.
5. Select Diagnosis from the Session Type screen.
6. Select the Selected Symptoms tab, and then select the following:
Powertrain - Engine system - Engine performance
7. Run and close Datalogger from the list of recommended candidates to expose the Extras tab.
8. Select the Extras tab.
9. From the Recommendations tab, select Run to perform the ' Configure existing module - Powertrain control
module ' option.
10. Follow all on-screen instructions to complete this task, ensuring all Diagnostic Trouble Codes (DTC) are
cleared.
11. When all tasks are complete, select the Session tab and then select the Close Session option.
12. Disconnect the diagnostic tool and battery power supply from the vehicle.