JTB00436NAS1

Page 1 of 4
TECHNICAL BULLETIN
JTB00436NAS1
07 AUG 2015
© Jaguar Land Rover North America, LLC
NOTE: The information in Technical Bulletins is intended for use by trained, professional Technicians with the knowledge,
tools, and equipment required to do the job properly and safely. It informs these Technicians of conditions that may occur on
some vehicles, or provides information that could assist in proper vehicle service. The procedures should not be performed by
'do-it-yourselfers'. If you are not a Retailer, do not assume that a condition described affects your vehicle. Contact an
authorized Jaguar service facility to determine whether this bulletin applies to a specific vehicle.
SECTION: 310-00
DMTL Pump Water/Ice Ingress
AFFECTED VEHICLE RANGE:
XJ Range (X351)
Model Year:
2010 Onwards
VIN:
V00001 Onwards
Manufacturing Plant: Castle Bromwich
Engine: V6 S/C 3.0L Petrol
V8 5.0L Petrol
V8 S/C 5.0L Petrol
MARKETS:
USA
CONDITION SUMMARY:
Situation: The engine Malfunction Indicator Lamp (MIL) may be illuminated. Upon diagnosis, the technician
may find one or more of the following Diagnostic Trouble Codes (DTC) stored in the Engine Control Module
(ECM): P043E-00, P0442-00, P0447-00, P0496-00, P2401-00, P2402-00, P2403-00, P2404-00, P2406-00,
P2407-00, P240A-00, P240C-00, and/or P240C-85.
Cause: This may be caused by water/ice, caused by spray from the road tires, becoming trapped within the
Diagnostic Module Tank Leakage (DMTL) pump filter.
Action: Should a customer express this concern, follow the Service Instruction below.
PARTS:
C2D40532
Evaporative emission canister
Quantity: 1
C2D30506
Fuel tank filler pipe
Quantity: 1
C2D49253
Protective Foam
Quantity: 1
TOOLS:
SDD with latest DVD and Calibration File
Jaguar Land Rover-approved Midtronics battery power supply
WARRANTY:
NOTE: Repair procedures are under constant review, and therefore times are subject to
change; those quoted here must be taken as guidance only. Always refer to TOPIx to obtain the
latest repair time.
NOTE: DDW requires the use of causal part numbers. Labor only claims must show the causal
part number with a quantity of zero.
DESCRIPTION
SRO
TIME
(HOURS)
CONDITION
CODE
CAUSAL
PART
Fuel tank filler pipe - Renew - 3.0L SC V6
19.55.33
1.5
42
C2C39518
http://topix.jaguar.jlrint.com/topix/service/document/564528
8/20/2015
Page 2 of 4
Evaporative emission canister - Renew 3.0L SC V6
17.15.13
2.6
42
C2C39518
Evaporative emission canister - Renew 5.0L NA/SC V8
17.15.13
1.9
42
C2C39518
Fuel tank filler pipe - Renew - 5.0L NA/SC
V8
19.55.33
1.3
42
C2C39518
Install the protective foam
05.10.10
0.1
42
C2C39518
NOTE: Normal Warranty procedures apply.
SERVICE INSTRUCTION:
1.
NOTE: one or both of the following must be verified.
Prior to replacing any components, verify one or both of the following:
• Diagnostic Module Tank Leakage (DMTL) pump failure
• Blocked 'Atmospheric vent pipe - DMTL pump to filter' due to debris breaching the 'DMTL (diagnostic
module - tank leakage) filter'
2. Install a new fuel tank filler pipe, (see TOPIx Workshop Manual section 310-01) follow Steps 1-11.
3. Install a new evaporative emission canister, (see TOPIx Workshop Manual section 303-13).
4. Install the protective foam in the area shown.
5. Make sure the protective foam is installed in the
correct area.
http://topix.jaguar.jlrint.com/topix/service/document/564528
8/20/2015
Page 3 of 4
6.
NOTE: the cable tie is supplied
installed through the protective foam.
Secure the protective foam to the metal pipe
with the supplied cable tie.
7. Install the rear wheel arch liner.
• Torque: 3Nm
8. Install the rear wheel.
• Torque: 128Nm
http://topix.jaguar.jlrint.com/topix/service/document/564528
8/20/2015
Page 4 of 4
CAUTION: a Jaguar Land Rover-approved Midtronics battery power supply must be connected to
the vehicle battery during SDD diagnosis / module programming.
CAUTION: ensure all ignition 'ON' / ignition 'OFF' requests are carried out; failure to perform these
steps may cause damage to control modules in the vehicle.
9. Connect the Jaguar Land Rover-approved Midtronics battery power supply to the vehicle battery.
10. Turn ignition 'ON' (engine not running).
11. Connect the Symptom Driven Diagnostics (SDD) system to the vehicle and begin a new session.
12. Follow the on-screen prompts, allowing SDD to read the VIN and identify the vehicle and initiating the data
collect sequence.
13. Read and clear the DTCs.
14. Follow all on-screen instructions to complete this task, ensuring all DTCs are cleared.
15. Exit the current session.
16. Disconnect the SDD and the battery power supply from the vehicle.
http://topix.jaguar.jlrint.com/topix/service/document/564528
8/20/2015