IB08-X-002F

BULLETIN NUMBER:
IB08-X-002F
IMPORTANT SERVICE
INFORMATION FOR:
 SERVICE MANAGER
 SERVICE ADVISOR
 TECHNICIAN
 PARTS DEPARTMENT
 WARRANTY PERSONNEL
ISSUE DATE:
APRIL 2017
GROUP:
MISCELLANEOUS
CERTIFIED CLEAN IDLE LABEL
INTRODUCTION AND REPLACEMENT PROCEDURES
AFFECTED VEHICLES
 2009-2018MY Isuzu N-Series
 2009-2010MY GMC/ Chevrolet W-Series Medium Duty Vehicles
Equipped with 5.2L 4HK1-TC Diesel Engine with GVW Greater Than
14,000 Pounds
This bulletin supersedes information bulletin IB08-X-002E. This bulletin is being
revised to update the Model Years. Please discard previous bulletin IB08-X-002E.
INFORMATION
Isuzu diesel engines available in the above affected vehicles meet the California Air
Resource Board’s (CARB) optional idling emissions standard of 30 grams per hour of
oxides of nitrogen (NOx) with no increase in the emission of other regulated pollutants.
As a result these vehicles have been approved as “Certified Clean Idle” and are
“exempt” from the Engine Shutdown System (ESS) requirement pursuant to Section
1956.8 of Title 13, California Code of Regulations. As required by the ESS regulation,
for “Certified Clean Idle” vehicles, Isuzu has introduced a tamper resistance “Certified
Clean Idle” label located on the driver’s side door panel.
It is important that this label remain, permanently, on the vehicle to identify it as
“Certified Clean Idle”. CARB requires this label as evidence that, at the time of
manufacture, the engine installed met the applicable emission standards. Should the
label be found missing or damaged during an inspection, a citation and penalties may
be issued. If the vehicle is operated in California with a damaged or missing clean idle
label, Isuzu recommends vehicle operators follow the 5 minute ESS requirement by
manually turning off the engine. Following this ESS requirement will keep the vehicle
operation compliant until a replacement label can be installed.
“Clean Air Idle” labels are printed with a serial number and registered to an individual
VIN. As a result, a replacement label will also include a new serial number which must
be registered to the vehicle’s VIN by the manufacturer. The below information is
provided to assist in acquiring, replacing and registering a replacement label.
PARTS INFORMATION
Replacement Certified Clean Idle labels may only be acquired directly from Isuzu
Commercial Truck of America (ICTA) vehicle distribution. Contact vehicle distribution at
1-877-478-9828, Prompt 2, then 4.
SERVICE INFORMATION
Important: Authorized dealers shall not allow vehicle owners to affix replacement
labels – failure to comply with this may result in legal action.
Take the following steps to request the label and complete the replacement procedure.
1. Complete the order form provided in the bulletin and fax it directly to ICTA vehicle
distribution at: 714-938-0603. The order form must be filled out completely.
Incomplete forms will result in delay of approval for label replacement. The
vehicle/engine information necessary to complete the order form is available on
the vehicle in the following locations:
VIN – VIN plate in driver side door jamb
Mileage - odometer
Family Name - valve cover engine emission label
Engine S/N – engine block passenger side
2. Once replacement is approved distribution will mail a replacement label, VIN
assignment printout and proof of installation letter directly to the requesting
dealer.
3. Affix the label per the label installation instructions below. If a vehicle cannot
return for installation, return the label to ICTA vehicle distribution.
Important: “Clean Air Idle” labels are VIN specific. Do not affix label to any VIN
other than what is indicated by the assignment print out.
4. Complete, sign and return the proof of installation letter. This will complete the
registration of the label.
CLEAN AIR IDLE LABEL ORDER FORM CA. STATE CERTIFIED
IMPORTANT – PLEASE READ FIRST
Make a copy of this form; complete all information
and fax or mail to:
ISUZU COMMERCIAL TRUCK AMERICA, INC.
1400 S. Douglass Road, Suite 100
Anaheim, CA. 92806-6906
Attn: Commercial Vehicle Distribution
Fax Number: (714) 938-0603
*TO BE FILLED OUT BY DEALER*
VIN:
MILEAGE:
Engine S/N:
Engine Family:
REASON FOR REPLACEMENT:
CLEAN AIR IDLE LABEL MISSING. (EXPLANATION REQUIRED)
CLEAN AIR IDLE LABEL DAMAGED, FADED OR UNREADABLE
OTHER (EXPLANATION REQUIRED)
Explanation:
DEALER NUMBER:
DEALER NAME: _________________________________________
CONTACT PERSON: _____________________________________
ADDRESS:_________________________________________________________________
CITY: _______________STATE: ____ ZIP_________TEL: (_____)__________________
For assistance please contact the Distribution Dept at 1-877-478-9828, Prompt 2 then 4
PREPARATION
LABEL INSTALLATION
Notice: The parts, vehicle, and ambient
temperature must be between 60°F and
90°F for optimum installation.
1) Clean the entire driver’s side surface
area above the door badge (Figure 1),
where the label will be adhered on door.
Wipe the application area with a solution
of one part isopropyl alcohol diluted with
one part water. Immediately dry the
installation area using a clean dry, lint
free cloth.
Figure 1
Figure 2
IMPORTANT:
Verify vehicle VIN, engine serial number, and
label serial number matches with Vehicle
Assignment VIN Creation printout provided
by ICTA Distribution (Figure 2). Do not affix
the label if the information does not match.
INSTALLATION
1) Create a ¼” fold to top portion of the
backing (Figure 3).
2) Align the bottom portion of the label to
the top side and left edge of the door
badge, using it as a guide (Figure 4).
Note: Bottom of label should be
approximately 1” from top side of
door badge.
Figure 3
Figure 4
3) Once positioned, press the adhesive
portion of the premask to the door to set.
Leave an open corner to peel off later
(Figure 5).
4) Using squeegee, firmly press the label to
the door while removing backing (Figure
6).
Figure 5
Figure 6
5) Once backing is removed, peel premask
off from open corner left earlier (Figure
7).
Caution: DO NOT allow premask to
retouch Clean Air Idle label.
6) Ensure the label is adhered properly to
the door and there are no damages,
scratches and/or defects to the label.
Note: If label is damaged, contact
ICTA immediately to order
replacement.
Keep the printout titled Vehicle
Assignment VIN Creation provided in the
VIN package on file for future reference.
Figure 7
Completed
ENGINE VALVE COVER EMISSIONS LABEL
ENGINE SERIAL NUMBER