A15-067
Service Bulletin Details
Public Details for: A15-067
"service bulletin - american honda consolidated some models from the previous airbag inflator campaigns into this current bulletin based on information from nhtsa. Do an in vin status inquiry and, if indicated, repair the vehicle. In certa
- 2007 - 2006 - 2005 - 2004 - 2003 - 2002 - 2001 -
Models from 2007
2007 HONDA ACCORD |
Models from 2006
2006 HONDA ACCORD |
Models from 2005
2005 HONDA ACCORD |
2005 HONDA CIVIC |
2005 HONDA CIVIC HYBRID |
Models from 2004
2004 HONDA ACCORD |
2004 HONDA CIVIC |
2004 HONDA CIVIC HYBRID |
2004 HONDA CIVIC NGV |
2004 HONDA CR-V |
Models from 2003
2003 HONDA ACCORD |
2003 HONDA CIVIC |
2003 HONDA CIVIC HYBRID |
2003 HONDA CIVIC NGV |
2003 HONDA CR-V |
2003 HONDA ELEMENT |
2003 HONDA ODYSSEY |
2003 HONDA PILOT |
Models from 2001
2001 HONDA CIVIC |
2001 HONDA CIVIC NGV |
(g)HONDA Service Bulletin December 19, 2015 15-067 02517 Version 2 Safety Recall: Front Passenger's Airbag lnflator Can Be Over-Pressurized Supersedes 15-067, dated October 1, 2015, to revise the information highlighted in yellow Replaces 13-034, Safety Recall: Front Passenger's Airbag lnf/ator Can Be Over-Pressurized Replaces 14-040, Safety Recall: Front Passenger's Airbag lnf/ator Can Be Over-Pressurized Replaces 15-041, Safety Recall: Front Passenger's Airbag lnf/ator Can Be Over-Pressurized REVISION SUMMARY • 2004 CR-V models were added to this safety recall. • A new video about counterfeit airbags was added to the REPAIR PROCEDURE. AFFECTED VEHICLES Year Model 2003-07 Accord 2001-05 Civic 2001-04 Civic GX 2003-05 Civic Hybrid 2002-04 CR-V 2003 Element 2002-03 Odyssey 2003 Pilot Trim ALL ALL ALL ALL ALL ALL ALL ALL VIN Range Check the iN VIN status for eligibility Check the iN VIN status for eligibility Check the iN VIN status for eligibility Check the iN VIN status for eligibility Check the iN VIN status for eligibility Check the iN VIN status for eligibility Check the iN VIN status for eligibility Check the iN VIN status for eligibility BACKGROUND American Honda consolidated some models from the previous airbag inflator campaigns into this current bulletin based on information from NHTSA. Do an iN VIN status inquiry and, if indicated, repair the vehicle. In certain vehicles, the front passenger airbag inflator could produce excessive internal pressure during airbag deployment. If an affected airbag deploys, the increased internal pressure may cause the inflator casing to rupture. Metal fragments could be propelled upward toward the windshield, or downward toward the front passenger's foot well, possibly causing an injury to vehicle occupants. NOTE: If the VIN status inquiry indicates that the vehicle is subject to any open safety recalls, including a driver's airbag inflator campaign/recall, make sure to also complete those recall repairs before returning the vehicle to the customer. If you are unable to complete any open recall, advise the customer of the recall status and when the recall may be completed. New and different inflators are available. You may receive a different part number than ordered, and the inflator may physically look different from previous replacement parts. As a result, there may be different installation instructions. Make sure you review this service bulletin for installation instructions and details about model applicability. PARTS INFORMATION and REPAIR PROCEDURE were updated to reflect these new parts. A new inflator has been added to the video included in this bulletin. On June 18, 2015, there was a change in the return process for driver and front passenger inflators. Refer to the PIB A15-0002, lnflator Kit Return Process for more information. CUSTOMER INFORMATION: The information in this bulletin is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely maintain your vehicle. These procedures should not be attempted by "do-it-yourselfers," and you should not assume this bulletin applies to your vehicle, or that your vehicle has the condition described. To determine whether this information applies, contact an authorized Honda automobile dealer. © 2015 American Honda Motor Co., Inc. - All Rights Reserved Page 1 of 20 On September 16, 2015, new processes for handling airbag inflators were introduced. Refer to the Ordering and Managing Replacement lnflators for more information on ordering and handling airbag inflators at your dealership. You can find the instructions in two places: • On SIS, select Search By Vehicle, then Technical Library. Enter keyword INFLATOR and select Job Aids. Select Ordering and Managing Replacement lnflators from the list. • From the iN, select Service, Warranty, then Claims Reference Guide. Under HOT TIPS/TOPICS, select Ordering and Managing Replacement lnflators. CUSTOMER NOTIFICATION Owners of affected vehicles will be sent a notification of this campaign. Do an iN VIN status inquiry to make sure the vehicle is shown as eligible. Some vehicles affected by this campaign may be in your used vehicle inventory. These vehicles must be repaired before they are sold. Should your dealership sell an unrepaired vehicle that subsequently causes injury or damage because of the recalled item, the dealership will be solely responsible to the damaged party, and will be required to defend and indemnify American Honda for any resulting claims. To see if a vehicle in inventory is affected by this recall, do a VIN status inquiry before selling it. CORRECTIVE ACTION Replace the passenger's airbag inflator, then return the original, undeployed inflator as directed. PARTS INFORMATION Part Name Part Number Ordered You may receive any of the following Quantity 2003 Accord Front Passenger's Airbag lnflator Kit 04 785-SDA-307 04 785-SDA-307 1 04 790-SDA-308 2004-07 Accord Front Passenger's Airbag lnflator Kit 04 785-SDA-306 04 785-SDA-306 04 790-SDA-305 1 2001-05 Civic (includes GX and Hybrid) Front Passenger's Airbag lnflator Kit 04 785-S5A-307 04 785-S5A-307 1 2002-04 CR-V Front Passenger's Airbag lnflator Kit 04 785-S9A-307 04 790-S5A-308 04 785-S9A-307 1 04 790-S9A-308 2003 Element Passenger (Front) Airbag lnflator Kit 04 785-SCV-307 04 785-SCV-307 1 04 790-SCV-308 2002 Odyssey Front Passenger's Airbag lnflator Kit 04 785-S0X-307 04 785-S0X-307 04 790-S0X-308 1 2003 Odyssey Passenger (Front) Airbag lnflator Kit 04 785-S0X-306 04 785-S0X-306 04 790-S0X-305 1 2003 Pilot Passenger (Front) Airbag lnflator Kit 04 785-S9V-307 04 785-S9V-307 04 790-S9V-308 1 NOTE: • The inflator kit box must be used to return the recalled inflator to its supplier. Be careful not to damage the inflator kit box. • If the recalled, undeployed inflator is not returned, the warranty claim for that vehicle will be charged back to your dealership. • To return the undeployed inflators, follow the shipping instructions outlined in PIB A15-0002, lnflator Kit Return Process. • Parts staff can scan the part number and serial number from the outside of the box into the warranty claim by using the Controlled Part Serial No. screen and scanning the applicable information. Refer to the Job Aid Ordering and Managing Replacement lnflators for more information. Page 2 of 20 WARRANTY CLAIM INFORMATION NOTE: • Process claims as quickly as possible so that resources can be properly allocated. • Enter the part number of the inflator that you received into the warranty claim, not the part number that you ordered. For more information, refer to step 6 of REPAIR PROCEDURE. • To avoid non-payment of warranty claims, the serial number on the box of the new airbag inflator must be entered in the warranty claim. For more information, refer to step 6 of REPAIR PROCEDURE. • To avoid a warranty claim being charged back to your dealership, you must return the original undeployed inflator to its supplier. Follow the shipping instructions outlined in PIB A 15-0002, lnflator Kit Return Process. • The serial number is encoded into the bar code printed on the label inside of the box and on a label attached to the outside of the box. If your dealership uses a scanner, you can scan the serial number from either place into the claim. • The part number is encoded into a barcode attached to the outside of the box. If your dealership uses a scanner, you can scan the part number into the claim. • If you confuse the serial number and part number when entering the claim information, your claim will automatically be rejected. • For more information about scanning and filing airbag inflator recall claims, refer to Ordering and Managing Replacement lnflators. From the iN, select Service, Warranty, then Claims Reference Guide. Under HOT TIPS/TOPICS, select Ordering and Managing Replacement lnflators. Replacing the front passenger's airbag inflator Year/ Model Operation Number 2003 Accord 7541B6 2004-07 Accord 7541B6 2001-05 Civic 2001-04 Civic GX Replacement Part number Flat Rate Time Defect Code Symptom Code Template ID Failed Part Number 04 785-SDA-307 0.7 hr 5SK00 JU400 15-067A 06780-SDN-A90ZA 04 790-SDA-308 0.7 hr 5SK00 JU400 15-067B 06780-SDN-A90ZA 04 785-SDA-306 0.7 hr 5SK00 JU400 15-067C 06780-SDN-A90ZA 04 790-SDA-305 0.7 hr 5SK00 JU400 15-067D 06780-SDN-A90ZA 04 785-S5A-307 0.7 hr 5SK00 JU500 15-067E 06780-S5A-A80ZA 04 790-S5A-308 0.7 hr 5SK00 JU500 15-067F 06780-S5A-A80ZA 7541B6 2003-05 Civic Hybrid 2002-04 CR-V 7521F7 04 785-S9A-307 0.7 hr 5SK00 JU600 15-067G 06780-S9A-A80ZA 7521F7 04 790-S9A-308 0.7 hr 5SK00 JU600 15-067H 06780-S9A-A80ZA 2003 7541A9 04785-SCV-307 0.8 hr 5SK00 JU700 15-067K 06780-SCV-AS0ZA 7541A9 04790-SCV-308 0.8 hr 5SK00 JU700 15-067L 06780-SCV-AS0ZA 7541A0 04 785-S0X-307 0.7 hr 5JK00 JU800 15-067M 06780-S0X-A 1OZA 7541A0 04 790-S0X-308 0.7 hr 5JK00 JU800 15-067N 06780-S0X-A 1OZA 7541A0 04 785-S0X-306 0.7 hr 5JK00 JU800 15-0670 06780-S0X-A 1OZA 7541A0 04 790-S0X-305 0.7 hr 5JK00 JU800 15-067P 06780-S0X-A 1OZA 7541A0 04 785-S9V-307 0.8 hr 5JK00 JU900 15-067Q 06780-S9V-A80ZA 7541A0 04 790-S9V-308 0.8 hr 5JK00 JU900 15-067R 06780-S9V-A80ZA Element 2002 Odyssey 2003 Odyssey 2003 Pilot Skill Level: Repair Technician Page 3 of 20 REPAIR PROCEDURE NOTE: • If the VIN status inquiry indicates that the vehicle is subject to any open safety recalls, including a driver's airbag inflator campaign/recall, make sure to also complete those recall repairs before returning the vehicle to the customer. If you are unable to complete any open recall, advise the customer of the recall status and when the recall could be completed. • Make sure you have the anti-theft code for the audio and navigation system (if applicable), then write down the frequencies for the audio unit's preset buttons. • Be careful not to damage any parts when replacing the inflator, and follow the procedure exactly. • If, before removing the airbag, you suspect that it may be the incorrect airbag for the vehicle or a counterfeit, do not remove the airbag. Contact your DPSM for assistance. • Make sure you have reviewed the SRS Precautions and Procedures in the service repair information before doing the REPAIR PROCEDURE. 1. Turn the ignition switch to the ON (II) position and check if the SRS indicator comes on for about 6 seconds, then turns off. • • If the indicator comes on, then turns off after about 6 seconds, go to step 2. If the indicator does not come on, or if it stays on, contact your DPSM for assistance. 2. Disconnect the battery negative cable and wait at least 3 minutes before continuing. 3. Remove the front passenger's airbag. Refer to the service repair information. 4. Place the airbag, face-down, on a clean shop towel. NOTE: • • The orientation of the airbag is critical because if the inflator is installed incorrectly, the harness will be too short when you reinstall the airbag. The brackets between the various models are similar but may differ from the example shown. Page 4 of 20 5. Visually inspect the airbag and the inflator for any unusual writing or markings. "IDENTIFYING COUNTERFIT AIRBAGS" VIDEO • • If there is nothing unusual about the airbag or the inflator, go to step 6. If there are any unusual markings, like an incorrect label or a model year written in marker, the airbag and inflator may not be the correct airbag and/or inflator for the vehicle or it may be a counterfeit part. For more information about counterfeit airbags, you can refer to safercar.gov, enter keywords MANAGING COUNTERFEIT, and select Recommended Dealer Guidance for Managing Counterfeit Air Bags from the list. If you suspect that the airbag or inflator is counterfeit, do not continue this procedure. Contact your DPSM for assistance. NON-STANDARD SAFETY LABEL HAND ENGRAVING ----~ GREASE PENCIL OR PAINT MARKINGS NO LABELS ON INFLATOR Page 5 of 20 6. Peel the label located inside the inflator box from its backing and attach it to the RO. For the warranty claim to be paid, the replacement inflator part number that you received must be included in the warranty claim. NOTE: • The replacement part number is printed on the top part of the label and the serial number is printed on the bottom. Make sure you attach the label to the RO and give it to the warranty clerk. • There may also be a colored sticker located in the kit; ignore it because it is not used. • Not all inflator kits have a label included. In those cases, write the serial number and part number from the side of the inflator box on the RO. The part number always starts with 04 7. PASSENGER INFLATOR PARTS BOX INFLATOR HARNESS SELF-ADHESIVE LABEL 7. INSTALLATION PARTS INFLATOR Remove the harness from both ends of the inflator brackets. Disconnect and remove the harness clip if applicable . Page 6 of 20 8. Short the red wires. NOTE: You must cut and short the wires as indicated to prevent accidental deployment. • Cut the red wires as shown. • Cut about 2 inches of the corrugated tube, then pull out the two red wires. • Strip away about 1 inch of the wire insulation, then twist the wires together. I • Tape the twisted ends with electrical tape. Page 7 of 20 9. Cut off the connector and short the yellow wires. NOTE: You must cut and short the wires as indicated to prevent accidental deployment. • Cut all four wires to remove the connector. • Cut about 2 inches of the corrugated tube , then pull out the yellow wires. Twist the ends together. • Tape the twisted ends with electrical tape. 10. Remove the four inflator nuts. INFLATOR NUTS Page 8 of 20 11 . Remove the inflator bracket. NOTE: You can only remove one of the brackets, as the other is welded to the airbag housing. 12. Remove the inflator by pushing it out. Page 9 of 20 13. Install the new inflator. Click on the image below for a short video about the different variations of the driver's and front passenger's replacement inflators involved with the recalls related to inflators. While both the driver's and front passengers inflators are shown in the video, this is informational only. Replace inflators only as directed by the iN VIN status inquiry. Check your part number against the ones listed for each installation procedure. Use the correct installation procedure for the part you received. Part Number 04 785-SDA-307 04 785-SSA-307 04 785-SDA-306 04 785-S9A-307 04 785-SCV-307 04 785-S0X-307 04 785-S0X-306 04 785-S9V-307 One connector looks like a "D" whereas the other connector is a circle. Make sure you insert the "D" shaped terminal into the airbag first. NOTE: There is a yellow band marking on the circle side. • D-SHAPED TERMINAL A white sticker covers the terminal. Page 10 of 20 • Slide the inflator in until the "D" aligns with the tab on the inflator bracket. There should be no space or gap between the inflator and bracket. Page 11 of 20 Check your part number against the ones listed for each installation procedure. Use the correct installation procedure for the part you received. Part Number 04 790-SDA-308 04 790-SSA-308 04 790-SCV-308 04 790-S9A-308 04 790-S0X-308 04 790-S9V-308 • One side of the inflator has a longer collar, a longer tab, a plastic cutout, and a small flat spot on the connector. The other side of the inflator has a shorter collar, a shorter tab, and a red dot. Make sure you insert the end with the longer collar into the airbag first. CUTOUT NEW INFLATOR RED DOT Page 12 of 20 • Slide the inflator in until the plastic cutout and the small flat spot align with the tab on the bracket. There should be no space or gap between the inflator and bracket. FIXED BRACKET END No gap CUTOUT Page 13 of 20 • Install the bracket included in the kit onto the airbag module. There should be a red dot visible on the end of the plastic connector. There should be no space or gap between the inflator and bracket. ADJUSTABLE BRACKET Page 14 of 20 Check your part number against the ones listed for each installation procedure. Use the correct installation procedure for the part you received. Part Number 04 790-SDA-305 04 790-S0X-305 • collars on this inflator are orange, not white. One side of the inflator has a longer collar, a tab, a plastic cutout, and a small flat spot on the connector. The other side of the inflator has a shorter collar, no tab, and a red dot. Make sure you insert the end with the longer collar into the airbag first. NEW INFLATOR ~ - ,-c_______ LONG COLLAR / ~ " RED DOT Page 15 of 20 • Slide the inflator in until the plastic cutout and the small flat spot align with the tab on the bracket. There should be no space or gap between the inflator and bracket. FIXED BRACKET END No gap CUTOUT TAB ON FIXED BRACKET Page 16 of 20 • Install the bracket included in the kit onto the airbag module. There should be a red dot visible on the end of the plastic connector. There should be no space or gap between the inflator and bracket. ADJUSTABLE BRACKET END No gap Page 17 of 20 14. Install the new 5 mm locknuts and torque them in sequence to 3.9 N•m (34 lb-in). Be sure there are no gaps between the inflator ends and the inflator brackets. 15. Remove the stickers covering the terminals on both sides of the new inflator. STICKER COVERING TERMINAL Page 18 of 20 16. Install the new inflator harness. • Make sure the airbag and harness are aligned as shown. NOTE: Make sure you have the orientation correct as shown below. If you connect the harness incorrectly, the harness cannot be removed, and you will not be able to reinstall the airbag because the harness will be too short. On the replacement inflators with plastic collars, connect the red wire connector to the connector with the red dot. On the replacement inflators without plastic collars, connect the red wire connector to the connector nearest the yellow band. RED WIRE CONNECTOR • Connect the two connectors. Align the "T" shape in the inflator harness connector with the T-shaped inflator connector, then press the connector into place. f;'\ Match up the "T" shape as shown . ~ The connectors are directional. INFLATOR HARNESS CONNECTOR ® Press the connector into place until it clicks. I?\ Wiggle the connector to \V make sure it's secure. I • After you hear each connector click, wiggle it to make sure it is secure. NOTE: If the connector is not properly aligned, it will come out. Page 19 of 20 17. Connect the harness to the inflator brackets. • • Insert the side without the shrink wrap tubing first. Insert the harness at the third "valley" in the corrugated tube. Insert the side of the harness with the shrink wrap tubing into the inflator bracket. Make sure the harness is securely inserted and that it does not sag. 18. Reinstall the passenger's airbag into the vehicle and torque the new locknuts to 9.8 N•m (7 .2 lb-ft). Refer to the service repair information. 19. Reconnect the battery negative cable and enter the anti-theft code for the audio and navigation system (if applicable), then enter the audio presets. 20. Turn the ignition to the ON (II) position and make sure the SRS indicator comes on for about 6 seconds, then turns off. 21. Do the idle learn procedure (2001-05 Civic). • • Make sure all electrical items (A/C, audio unit, defogger, lights, etc.) are turned off, then start the engine. Let the engine reach its normal operating temperature (the cooling fans cycle twice; the coolant temperature is about 194 ° F). • • Let the engine idle for at least 5 minutes with the throttle fully closed and with all electrical items turned off. If the cooling fans cycle on while doing an idle learn, add the time the cooling fans are on to the 5 minute idle learn time. 22. Put the original inflator into the box the new one came in. Make sure there is no other hardware in the box because if the package rattles, it will not be accepted by the courier. 23. Follow the shipping instructions outlined in PIB A 15-0002 to return the undeployed inflator. 24. Give your warranty clerk the RO that includes the replacement inflator serial number and replacement part number. For the warranty claim to be paid, the replacement inflator part number must be included in the warranty claim. END Page 20 of 20